BS EN 60684-3-121 to 124-2002 Specification for flexible insulating sleeving Specification requirements for individual types of sleeving Specifications for individual types of slee.pdf

《BS EN 60684-3-121 to 124-2002 Specification for flexible insulating sleeving Specification requirements for individual types of sleeving Specifications for individual types of slee.pdf》由会员分享，可在线阅读，更多相关《BS EN 60684-3-121 to 124-2002 Specification for flexible insulating sleeving Specification requirements for individual types of sleeving Specifications for individual types of slee.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60684-3-121 to 124:2001 IEC 60684-3-121 to 124:2001 Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheets 121 to 124: Extruded silicone sleeving The European Standard EN 60684-3-121 to 124:2001 has the status of a British Standard ICS 29.0

2、35.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 60684-3-121 to 124:2001 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strate

3、gy Committee on 2 April 2002 BSI 2 April 2002 ISBN 0 580 39255 4 National foreword This British Standard is the official English language version of EN 60684-3-121 to 124:2001. It is identical with IEC 60684-3-121 to 124:2001. It supersedes BS 6893-3-121 and 122:1995 and BS EN 60684-3-123 and 124:19

4、95 which are withdrawn. The UK participation in its preparation was entrusted by Technical Committee GEL/15, Insulating materials, to Subcommittee GEL/15/3/5, Sleevings, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary

5、. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-refe

6、rences The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Cata

7、logue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the te

8、xt; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front co

9、ver, an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 60684-3-121 to 124 NORME EUROPENNE EUROPISCHE NO

10、RM October 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any

11、 means reserved worldwide for CENELEC members. Ref. No. EN 60684-3-121 to 124:2001 E ICS 29.035.20 Supersedes HD 523.3.121 Part 2 : Methods of test (IEC 60684-2); Part 3 : Specification requirements for individual types of sleeving (IEC 60684-3). This standard contains four of the sheets comprising

12、part 3 as follows: Sheet 121: Extruded silicone sleeving General purpose, flame retarded Sheet 122: Extruded silicone sleeving General purpose, flame retarded, low volatile content Sheet 123: Extruded silicone sleeving General purpose Sheet 124: Extruded silicone sleeving General purpose, low volati

13、le content. Page3 EN606843121to124:2001FLEXIBLE INSULATING SLEEVING Part 3: Specifications for individual types of sleeving Sheets 121 to 124: Extruded silicone sleeving 1 Scope These sheets of IEC 60684-3 gives the requirements for four types of non-heatshrinkable sleeving, extruded from silicone e

14、lastomer. These sleevings are normally available with internal diameter up to 25 mm and in a range of wall thicknesses between 0,1 mm and 2,0 mm. National standards may select a restricted list of preferred combinations of internal diameter and wall thickness. These sleevings are normally available

15、in the following opaque colours: black, brown, red, orange, yellow, green, blue, violet, grey, white and pink. They are also available in a translucent form. Sizes or colours other than those specifically listed in this standard may be available as custom items. These items shall be considered to co

16、mply with this standard if they comply with the other property requirements listed in table 2. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IEC 60684. For dated references, subsequent amendmen

17、ts to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IEC 60684 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of

18、the normative document referred to applies. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 60684-1:1980, Specification for flexible insulating sleeving Part 1: Definitions and general requirements IEC 60684-2:1997, Specification for flexible insulating slee

19、ving Part 2: Methods of test IEC 60757:1983, Code for designation of colours Page4 EN606843121to124:20013 Designation The sleeving shall be identified by the following designation: Sleeving IEC 60684 3 121- 2,5 / 0,5 GN Description IEC publication Number Part Sheet Size (nominal bore and wall thickn

20、ess, in millimetres) Colour Any abbreviation used for colour shall comply with IEC 60757, where applicable. Non-standard colours shall be written out in full. The abbreviation for translucent shall be “TL” 4 Requirements In addition to the general requirements given in IEC 60684-1, the sleeving shal

21、l comply with the requirements in tables 1, 2 and 3. 5 Product qualification Product qualification shall normally be based on results from 8 mm internal diameter black sleeving. Colour fastness to light shall be qualified for all colours. Page5 EN606843121to124:2001Table 1 Nominal internal diameter

22、Nominal internal diameter mm Tolerance on internal diameter mm 0,3 +0,10 0,05 0,5 0,8 +0,15 0,10 1,0 1,5 2,0 +0,20 0,15 2,5 3 4 5 0,20 6 8 10 12 0,25 16 20 25 0,50 NOTE 1 Measurements shall be made to the nearest 0,05 mm. NOTE 2 See table 3 for wall thicknesses. Page6 EN606843121to124:2001Table 2 Pr

23、operty requirements Property IEC 60684-2 Clause or subclause Units Max. or min. Requirements Remarks Dimensions 3 mm Tables 1 and 3 Volatile content (sheets 122 and 124 only) 12 % Max. 1,0 Bending after heating 13 There shall be no cracking. The original colour shall still be clearly recognisable. T

24、est temperature: 200 C 5 K. The mandrel diameter shall be twice the external diameter of the sleeve Bending at low temperature 14 There shall be no cracking. Test temperature 60 C or lower. For nominal internal diameters of 8 mm, and below use a mandrel 18 to 20 times the nominal wall thickness. For

25、 nominal internal diameters of above 8 mm, use strips and a mandrel of 8 to 10 times the nominal wall thickness Tensile strength 19.1 and 19.2 MPa Min. 5,5 Jaw separation: (500 25) mm/min Elongation at break 19.1 and 19.2 % Min. 200 Jaw separation: (500 25) mm/min Breakdown voltage 21 kV Min. See ta

26、ble 3 Volume resistivity at room temperature after damp heat 23.4.2 23.4.4 M Min. 1 10 11 1 10 10 Flame propagation (sheets 121 and 122 only) 26 Method A s Max. 60 In addition the indicator flag shall not be burned away. The cotton shall not be ignited. Electrolytic corrosion 31 Max. Negative pole 1

27、, 4 Positive pole A/B Visual method Thermal endurance 37 Min. 180 The end point shall be 50 % of the initial value of tensile strength Page7 EN606843121to124:2001Table 3 Requirements for wall thickness and breakdown voltage The breakdown voltage shall be determined by any of the methods given in 21.

28、2, 21.3, 21.4 and 21.5 of IEC 60684-2. The central value shall comply with the minimum value in the table below. The rate of application of the voltage shall be either 500 V/s or such that the required value is reached within 10 s to 20 s. Wall thickness mm Breakdown voltage (min.) kV Nominal Tolera

29、nce Room temperature 180 C 3 K 0,1* +0,10 0 1,3 1,0 0,2 0,4 0,5 0,7 1,0 +0,15 0,05 2,4 4,7 5,5 8,0 10,7 1,8 3,5 4,0 6,0 8,0 1,5 2,0 0,20 16,0 20,0 12,0 15,0 * This wall thickness is normally only available for sleevings of nominal internal diameter up to and including 1 mm. _ Page8 EN606843121to124:

30、2001Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text

31、 and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies

32、 (including amendments). NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60684-1 1980 Specification for flexible insulating sleeving Part 1: Definitions and general requirements EN

33、 60684-1 1995 IEC 60684-2 1997 Part 2: Methods of test EN 60684-2 1997 IEC 60757 1983 Code for designation of colours HD 457 S1 1985 Page9 EN606843121to124:2001BS EN 60684-3-121 to 124:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national bod

34、y responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the lates

35、t amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which ca

36、n be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreig

37、n standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI impleme

38、ntation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic info

39、rmation services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts o

40、n the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi

41、- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Pate

42、nts Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary

43、 details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.