BS EN 147000-1995 Harmonized system of quality assessment for electronic components - Generic specification - Sockets for use with electrical relays of assessed quality《电子元器件质量评定协调.pdf

《BS EN 147000-1995 Harmonized system of quality assessment for electronic components - Generic specification - Sockets for use with electrical relays of assessed quality《电子元器件质量评定协调.pdf》由会员分享，可在线阅读，更多相关《BS EN 147000-1995 Harmonized system of quality assessment for electronic components - Generic specification - Sockets for use with electrical relays of assessed quality《电子元器件质量评定协调.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 147000:1995 Harmonized system of quality assessment for electronic components Generic specification: Sockets for use with electrical relays of assessed quality The European Standard EN147000:1993 has the status of a BritishStandardBSEN 147000:1995 This BritishStandard, having

2、been prepared under the directionof the Electrotechnical Sector Board,was published undertheauthority of the StandardsBoard and comes intoeffect on 15January1995 BSI01-2000 The following BSI references relate to the work on this standard: Committee reference ECL/1 Special announcement in BSI News Au

3、gust1994 ISBN 0 580 23499 1 Cooperating organizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, comprises the national committees of the following countries: Austria Italy Belgium Luxembourg Denmark Netherlands

4、 Finland Norway France Portugal Germany Spain Greece Sweden Iceland Switzerland Ireland United Kingdom Amendments issued since publication Amd. No. Date CommentsBSEN 147000:1995 BSI 01-2000 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN147000

5、5 National annex NA (informative) Committees responsible 22 National annex NB (informative) Cross-references 22BSEN 147000:1995 ii BSI 01-2000 National foreword This BritishStandard has been prepared under the direction of the Electrotechnical Sector Board and is the English language version of EN14

6、7000:1993 Generic specification: Sockets for use with electrical relays of assessed quality, published by the European Committee for Electrotechnical Standardization (CENELEC) Electronic Components Committee (CECC). The BritishStandard which implements the CECC Rules of Procedure is BS9000-2:1991 Ge

7、neral requirements for a system for electronic components of assessed quality Part2. Specification for the national implementation of the CECC system. The foreword of EN147000 makes reference to the “date of withdrawal”, dow, of the conflicting national standard. In this case there is no existing co

8、nflicting national standard. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of p

9、ages This document comprises a front cover, an inside front cover, pagesi andii, the EN title page, pages2 to22, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the i

10、nside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN147000 December1993 UDC Descriptors: Quality, electronic components, sockets English version Generic specification: Sockets for use with electrical relays of assessed quality Spcification gnrique: Supports pour relais sous assuran

11、ce de la qualit Fachgrundspezifikation: Gtebesttigte Fassungen Fr die Verwendung mit elektischen Schaltrelais This European Standard was approved by the CENELEC Electronic Components Committee (CECC) on10August1992. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which

12、stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European St

13、andard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the nat

14、ional electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. The membership of the CECC is identical, with the exception of the national electrotechn

15、ical committees of Greece, Iceland and Luxembourg. CECC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1993 Copyright reserved to CENELEC

16、 members Ref. No. EN147000:1993 EEN 147000:1993 BSI 01-2000 2 Foreword The CENELEC Electronic Components Committee (CECC) is composed of those member countries of the European Committee for Electrotechnical Standardization (CENELEC) who wish to take part in a harmonized System for electronic compone

17、nts of assessed quality. The object of the System is to facilitate international trade by the harmonization of the specifications and quality assessment procedures for electronic components, and by the granting of an internationally recognized Mark, or Certificate, of Conformity. The components prod

18、uced under the System are thereby acceptable in all member countries without further testing. This specification was prepared by CECC WG16 Relays. The text of the draft based on document CECC (Secretariat)2780 was submitted to the formal vote; together with the voting report, circulated as document

19、CECC(Secretariat)3140, it was approved by CECC as EN147000 on10August1992. The following dates were fixed: Contents Page Foreword 2 1 Scope 5 2 General 5 2.1 Order of precedence 5 2.2 Related documents 5 2.3 Units, symbols and terminology 6 2.4 Preferred values 6 2.5 Marking 6 3 Terms and definition

20、s 6 3.1 Terms relating to sockets 6 3.2 Terms relating to contacts 7 3.3 Electrical properties of contacts 8 3.4 Terms relating to tools and accessories 8 4 Quality assessment procedures 9 4.1 Primary stage of manufacture 9 4.2 Structurally similar components 9 4.3 Qualification approval procedures

21、9 4.4 Quality conformance inspection 9 4.5 Division into groups 9 4.6 Resubmission of rejected lots 9 4.7 Certified test records 9 4.8 Delivery of sockets submitted to tests 9 4.9 Delayed delivery 10 4.10 Supplementary procedure for deliveries 10 4.11 Unchecked parameters 10 4.12 Release for deliver

22、y before completion of Group B tests 10 5 Test and measurement procedures 10 5.1 General 10 5.2 Alternative test methods 10 5.3 Precision of measurement 10 5.4 Requirements in detail specifications 10 5.5 Standard conditions for testing 10 5.6 Visual inspection and check of dimensions 11 5.7 Weighin

23、g 11 5.8 Insertion and withdrawal force 12 5.9 Mounting and fixture 12 5.10 Retention force of the socket contact 12 latest date of announcement of the EN at national level (doa) 1993-02-11 latest date of publication of an identical national standard (dop) 1993-08-11 latest date of declaration of na

24、tional standards obsolescence 1993-08-11 latest date of withdrawal of conflicting national standards (dow) 2003-02-11EN 147000:1993 BSI 01-2000 3 Page 5.11 Contact retention into insulator body 12 5.12 Replacement of removable contacts 13 5.13 Wiring of crimping contacts 13 5.14 Dielectric strength

25、test 14 5.15 Insulation resistance test 14 5.16 Contact circuit resistance 14 5.17 Shock 15 5.18 Bump 15 5.19 Vibration 16 5.20 Climatic sequence 16 5.21 Rapid change of temperature 17 5.22 Salt spray 18 5.23 Soldering 18 5.24 Resistance to cleaning solvents 18 5.25 Fluid contamination 19 5.26 Flamm

26、ability test 20 5.27 Thermal endurance 20 5.28 Mechanical endurance 20 5.29 Electrical overload 21 Table 1 8 Table 2 194 blankEN 147000:1993 BSI 01-2000 5 1 Scope This specification covers the general requirements for sockets used with plug in electrical relays of assessed quality. 2 General 2.1 Ord

27、er of precedence In the event of any conflict between documents, the order of precedence shall be: 1) the detail specification 2) the sectional specification 3) the generic specification 4) The Internal Regulations of the FEN e.V., or any other international documents (for example of the IEC) to whi

28、ch reference is made. The same order of precedence shall apply to equivalent national documents. 2.2 Related documents Reference to the following documents is made in this specification. ISO1000(1981) SI units and recommendations for the use of their multiples and of certain other units. IEC27-1 (19

29、71) Letter symbols to be used in electrical technology. General. (Amendment4, 1983) IEC50 International Electrotechnical Vocabulary. IEC60 High voltage test techniques. IEC68-1(1988) Environmental testing. Part1: General and guidance. (Amendment1, 1992) IEC617 Graphical symbols for diagrams. IEC947-

30、1(1988) Degrees of protection of enclosures for low-voltage switchgear and controlgear. IEC255 Electrical relays. IEC410(1973) Sampling plans and procedures for inspection by attributes. (SeeCECC00007, 1973) IEC443(1974) Stabilised supply apparatus for measurement. CECC00109(1974)Certified test reco

31、rds. CECC00114 Quality assessment procedures/Part II (1992): Qualification approval of electronic components. SECRETARIATS NOTE: At the date of publication of this specification the publication state of IEC60 and IEC255 is: IEC60-1(1988) General definitions and test requirements. IEC60-2(1973) Test

32、procedures. IEC60-3(1976) Measuring devices. IEC60-4(1977) Application guide for measuring devices. IEC255-0-20 (1974) Contact performance of electrical relays. IEC255-1-00 (1975) All-or-nothing electrical relays. IEC255-3 (1989) Single input energizing quantity measuring relays with non-specified t

33、ime or with independent specified time. IEC255-5 (1977) Insulation tests for electrical relays. IEC255-6 (1978) Measuring relays with more than one input energizing quantity. IEC255-7 (1991) Test and measurement procedures for electromechanical all-or nothing relays.EN 147000:1993 6 BSI 01-2000 2.3

34、Units, symbols and terminology Units, graphical symbols, letter symbols and terminology shall, whenever possible, be taken from the following documents: ISO1000, SI units and recommendations for the use of their multiples and of certain other units. IEC27-1, Letter symbols to be used in electrical t

35、echnology, Part1: General. IEC50, International Electrotechnical Vocabulary. IEC617, Graphical symbols for diagrams. 2.4 Preferred values The stated values in the detail specification shall be chosen, as far as possible, from the preferred values of the relevant part of IEC255. 2.5 Marking The secti

36、onal or detail specification shall indicate the identification criteria and other information to be shown on the socket and/or packing. The letter or colour code shall be described in full or reference made to the appropriate specifications. The order of priority for marking small sockets shall be s

37、pecified. The marking shall, as a minimum, consist of: the trade mark or the manufacturers name; the type and variants code; the manufacturing data code; the CECC logo. 3 Terms and definitions The following paragraphs contain specific additional terminology applicable to sockets for plug-in electrom

38、echanical relays and shall be included into each national harmonized specification. 3.1 Terms relating to sockets 3.1.1 front side side where the relay is plugged 3.1.2 rear side side used for the wiring 3.1.3 contact conducting part of the socket used for electrical connection between the terminal

39、of the relay and the wiring electrical continuity is obtained by mechanical pressure between one part of the contact and the terminals of the relay 3.1.4 insulator body part of the socket which maintains contacts in position and ensures insulation between them 3.1.5 mounting hardware accessories att

40、ached or not to the socket and used for: mounting firmly on panel or other bearing devices; secure firmly the relay after mounting. 3.1.6 polarising device device which disables incorrect connectingEN 147000:1993 BSI 01-2000 7 3.1.7 sealing barrier device which makes sure tightness of the wiring 3.1

41、.8 sealing plug device used in place of non-wired contacts to obtain tightness on the rear side 3.2 Terms relating to contacts 3.2.1 pin contact conducting part of the relay used for connection with the socket 3.2.2 socket contact conducting part of the socket used for connection with the relay 3.2.

42、3 removable contact contact maintained inside the insulator body by suitable device, and removable from the front or the rear side by use of a tool 3.2.4 fixed contact non-removable contact 3.2.5 barrel part of the socket contact in which a pin contact is inserted 3.2.6 wire barrel part of the conta

43、ct used for connection to the wiring 3.2.7 crimp contact contact for which the wiring is obtained by crimping the wire barrel 3.2.8 solderable contact contact for which the wiring is obtained by soldering of the wire barrel to the terminal pin 3.2.9 solder pin contact contact for which connection to

44、 the wiring is obtained by soldering the pin to a printed circuit 3.2.10 pin contact for wrapping contact for which connection to the wiring is obtained by wrapping the wire around the pin 3.2.11 screw contact contact for which connection to the wiring is obtained by locking the wire on the contact

45、by use of a screw 3.2.12 contact size the contact size is expressed by an AWG number (American Wire Gauge) unless otherwise specified the same number expresses the gauge for the socket and the pin contact reduced wire barrel contacts may be used and are specified in detail specifications. Their desi

46、gnation is expressed by the size of the barrel followed by the size of the wire barrelEN 147000:1993 8 BSI 01-2000 Ex.: Gauge16socket contact barrel with gauge18wire barrel (reduced size). Table 1 shows nominal section of the wire, expressed in AWG and mm 2 , as well as the crimping pulling strength

47、. Table 1 3.3 Electrical properties of contacts 3.3.1 contact current current which flows through the contact 3.3.2 maximum continuous service current the highest value which can be withstood permanently by a contact 3.4 Terms relating to tools and accessories 3.4.1 mounting gauge metal panel used t

48、o check the mounting dimensions of the socket and some of the electrical characteristics 3.4.2 dummy relay it is made up of a can with fixture, welded on a header equipped only with terminals, polarizing devices, silicon gaskets can or header are issued from standard manufacturing parts. All the fin

49、ishing is identical to the real relay (can and contacts plating, etc.) 3.4.3 wired dummy relay identical to the former except following conditions: it is filled with hard insulating material which gives it the mass and center of gravity close to those of the real relay; male contacts are connected by two with a wire, of the same size as that used for contact-wiring, as specified in the detail specification. 3.4.4 male contact for test (for contact resistance test) relay terminal of the same material and finishing as the sta