BS EN 14319-1-2013 Thermal insulating products for building equipment and industrial installations In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate foam (PIR)n.pdf

《BS EN 14319-1-2013 Thermal insulating products for building equipment and industrial installations In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate foam (PIR)n.pdf》由会员分享，可在线阅读，更多相关《BS EN 14319-1-2013 Thermal insulating products for building equipment and industrial installations In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate foam (PIR)n.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 14319-1:2013Thermal insulating products for building equipment and industrial installations In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate foam (PIR

2、) productsPart 1: Specification for the rigid foam dispensed system before installationBS EN 14319-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 14319-1:2013. The UK participation in its preparation was entrusted to T e c h n i c a l Committee PRI/72, R

3、igid cellular materials.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013

4、. Published by BSI Standards Limited 2013.ISBN 978 0 580 53439 3 ICS 91.100.60 Compliance with a British Standard cannot confer immunityfrom legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013.Amendments issued s

5、ince publicationDate T e x t a f f e c t e dBS EN 14319-1:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14319-1 January 2013 ICS 91.100.60 English Version Thermal insulating products for building equipment and industrial installations - In-situ formed dispensed rigid polyurethane (PUR) an

6、d polyisocyanurate foam (PIR) products - Part 1: Specification for the rigid foam dispensed system before installation Produits disolation thermique destins aux applications du btiment et aux installations industrielles - Produits en mousse rigide de polyurthanne (PUR) et de polyisocyanurate (PIR) i

7、njecte, forms en place - Partie 1: Spcifications relatives aux systmes dinjection du polyurthanne et du polyisocyanurate rigide avant mise en uvre Wrmedmmstoffe fr die technische Gebudeausrstung und fr betriebstechnische Anlagen in der Industrie - An der Verwendungsstelle hergestellter Wrmedmmstoff

8、aus Polyurethan (PUR)- und Polyisocyanurat (PIR)-Gieschaum - Teil 1: Spezifikation fr das Schaumsystem vor dem Einbau This European Standard was approved by CEN on 24 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving th

9、is European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official

10、versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Aust

11、ria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swede

12、n, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Me

13、mbers. Ref. No. EN 14319-1:2013: EBS EN 14319-1:2013EN 14319-1:2013 (E) 2 Contents Page Foreword . 4 1 Scope 5 2 Normative references . 5 3 Terms, definitions, symbols and abbreviations 6 3.1 Terms and definitions 6 3.2 Symbols and abbreviations . 8 4 Requirements . 9 4.1 General . 9 4.2 For all app

14、lications . 10 4.3 For specific applications 12 5 Test methods 15 5.1 Sampling . 15 5.2 Conditioning . 15 5.3 Testing 15 6 Designation code . 18 7 Evaluation of conformity 18 7.1 General . 18 7.2 Initial type testing . 19 7.3 Factory production control 19 8 Marking, labelling and technical informati

15、on 19 8.1 Marking and labelling . 19 8.2 Technical information 19 Annex A (normative) Determination of substrate adhesion strength perpendicular to faces . 21 A.1 Principle 21 A.2 Apparatus . 21 A.3 Test specimen 21 A.4 Test specimen preparation procedure 21 A.5 Test procedure . 21 A.6 Report . 21 A

16、nnex B (normative) Initial type testing (ITT) and Factory production control (FPC) . 23 Annex C (normative) Determination of the aged values of thermal resistance and thermal conductivity 25 C.1 General . 25 C.2 Sampling and test specimen preparation . 26 C.3 Determination of the initial value of th

17、ermal conductivity . 26 C.4 Determination of the accelerated aged value of thermal conductivity 27 C.5 Fixed increment procedure 29 C.6 “Safe values” curve of aged thermal conductivity values versus temperature 32 Annex D (normative) Determination of the reaction profile and free-rise density 33 D.1

18、 Introduction 33 D.2 Principle 33 D.3 Apparatus . 33 D.4 Procedure . 33 D.5 Free-rise density 34 Annex E (normative) Test sample preparation method for the specimens for the thermal conductivity test . 35 E.1 Principle 35 BS EN 14319-1:2013EN 14319-1:2013 (E) 3 E.2 Procedure . 35 Annex F (normative)

19、 Determination of the reference density . 36 F.1 Principle 36 F.2 Procedure . 36 F.3 Measurement of the reference density 36 Annex G (normative) Test sample preparation method for the test specimens other than for determining thermal conductivity 37 G.1 Principle 37 G.2 Procedure . 37 Annex H (norma

20、tive) Reaction to fire of the product . 38 H.1 Scope 38 H.2 Product and installation parameters . 38 H.3 Mounting and fixing . 39 H.4 Field of application . 41 Annex I (normative) Reaction to fire of the products in standardised assemblies simulating end-use applications . 43 I.1 Scope 43 I.2 Produc

21、t and installation parameters . 43 I.3 Mounting and fixing . 44 I.4 Field of application . 47 Annex ZA (informative) Clause of this European Standard addressing the provisions of the EU Construction Products Directive . 50 ZA.1 Scope and relevant characteristics . 50 ZA.2 Procedure for attestation o

22、f conformity of in-situ formed dispensed rigid polyurethane (PUR) and rigid polyisocyanurate foam (PIR) products 52 ZA.3 CE Marking and labelling . 55 Bibliography 57 BS EN 14319-1:2013EN 14319-1:2013 (E) 4 Foreword This document (EN 14319-1:2013) has been prepared by Technical Committee CEN/TC 88 “

23、Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2013, and conflicting national standards shall be withdraw

24、n at the latest by July 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to

25、 CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This European Standard consists of two parts which form a pack

26、age. The first part is the harmonised part satisfying the mandate and the CPD and is the basis for the CE marking covering the products, which are placed on the market. The second part, which is the non-harmonised part, covers the specification for the installed products. Both parts need to be used

27、for the application of the insulation products in the end-use applications covered by EN 14319. This European Standard is one of a series for expanded perlite, exfoliated vermiculite and polyurethane/polyisocyanurate in-situ formed insulation products used in building equipment and industrial instal

28、lations, but this standard may be used in other areas where appropriate. The reduction in energy used and emissions produced during the installed life of insulation products exceeds by far the energy used and emissions made during the production and disposal processes. EN 14319-1, Thermal insulating

29、 products for building equipment and industrial installations In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products consists of the following parts: Part 1: Specification for the rigid foam spray system before installation (the present document) Part 2: Specificati

30、on for the installed insulation products According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yu

31、goslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14319-1:2013EN 14319-1:2013 (E) 5 1 Scop

32、e This European Standard specifies requirements for in-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products for the insulation of building equipment and industrial installations, for example industrial storage vessels, pipes and ducts used for the supply of fuels,

33、oil, other liquids, hot and cold water, air and other gases. Depending on the type of foam products complying with this standard, they may have service temperature ranges which lie within the limits of 200 C. This Part 1 of this European Standard is a specification for the rigid foam system before i

34、nstallation. Part 1 of this European Standard describes the product characteristics and it includes procedures for testing, marking and labelling and the rules for evaluation of conformity. This European Standard does not specify the required levels of all properties to be achieved by a product to d

35、emonstrate fitness for purpose in a particular end-use application. The required levels are to be found in regulations or non-conflicting standards. This European Standard does not cover factory made rigid polyurethane or polyisocyanurate foam insulation products or in-situ products intended to be u

36、sed for the insulation of buildings. This European Standard does not specify performance requirements for direct airborne sound insulation and acoustic absorption applications. NOTE Foam products are either called flexible or rigid. The flexible products are used in upholstery and mattresses and are

37、 characterised by their ability to deflect, support and recover to their original thickness continually during their in-use phase. Those that are not flexible are termed rigid and do not possess these flexible characteristics. They are mostly used for thermal insulation purposes and vary widely in t

38、heir compression strength values. Once the cell structure is crushed in a rigid foam, it does not recover its thickness fully. Some of these rigid foams are very low in density with very low compression strengths and are sometimes described “commercially” as “soft foams” or “semi-rigid” foams. This

39、note has been included to clarify that all foams with such descriptions are covered by this standards used of the term rigid foam. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated ref

40、erences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 312, Particleboards Specifications EN 508-1, Roofing products from metal sheet Specification for self-supporting products of steel, aluminium or stain

41、less steel sheet Part 1: Steel EN 520, Gypsum plasterboards Definitions, requirements and test methods EN 823, Thermal insulating products for building applications Determination of thickness EN 826:1996, Thermal insulating products for building applications Determination of compression behaviour EN

42、 1602, Thermal insulating products for building applications Determination of the apparent density EN 1604, Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions BS EN 14319-1:2013EN 14319-1:2013 (E) 6 EN 1606

43、, Thermal insulating products for building applications Determination of compressive creep EN 12086:1997, Thermal insulating products for building applications Determination of water vapour transmission properties EN 12667:2001, Thermal performance of building materials and products Determination of

44、 thermal resistance by means of guarded hot plate and heat flow meter methods Products of high and medium thermal resistance EN 12939, Thermal performance of building materials and products Determination of thermal resistance by means of guarded hot plate and heat flow meter methods Thick products o

45、f high and medium thermal resistance EN 13172:2012, Thermal insulation products Evaluation of conformity EN 13238, Reaction to fire tests for building products Conditioning procedures and general rules for selection of substrates EN 13468, Thermal insulating products for building equipment and indus

46、trial installations Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using test data from reaction to fire tests EN 13823:2010, Reaction to fire te

47、sts for building products Building products excluding floorings exposed to the thermal attack by a single burning item EN 14308:2009, Thermal insulation products for building equipment and industrial installations Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products Sp

48、ecification EN 14706, Thermal insulating products for building equipment and industrial installations Determination of maximum service temperature EN ISO 1182, Reaction to fire tests for products Non-combustibility test (ISO 1182) EN ISO 1716, Reaction to fire tests for products Determination of the

49、 gross heat of combustion (calorific value) (ISO 1716) EN ISO 9229:2007, Thermal insulation Vocabulary (ISO 9229:2007) EN ISO 11925-2:2010, Reaction to fire tests Ignitability of products subjected to direct impingement of flame Single-flame source test (ISO 11925-2:2010) EN ISO 13787, Thermal insulation products for building equipment and industrial installations Determination of declared thermal conductivity (ISO 13787) ISO 4590, Rigid cellular plastics Determination of the volume percentag