BS EN 13473-1-2001 Reinforcement - Specifications for multi-axial multi-ply fabrics - Designation《加筋 多轴向多股织物规范 标识》.pdf

《BS EN 13473-1-2001 Reinforcement - Specifications for multi-axial multi-ply fabrics - Designation《加筋 多轴向多股织物规范 标识》.pdf》由会员分享，可在线阅读，更多相关《BS EN 13473-1-2001 Reinforcement - Specifications for multi-axial multi-ply fabrics - Designation《加筋 多轴向多股织物规范 标识》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 13473-1:2001Reinforcement Specifications for multi-axial multi-ply fabrics Part 1: Designation The European Standard 13473-1:2001 has the status of a British Standard ICS 59.100.99; 83.120 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 13473-1:2001

2、 This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 August 2001 BSI 07-2001 ISBN 0 580 37760 1 National foreword This British Standard is the off

3、icial English language version of EN 13473-1:2001. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: A list of organizations represented on this committee can be obtained on requ

4、est to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of t

5、he BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. ai

6、d enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document co

7、mprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM E

8、N 13473-1 June 2001 ICS 59.100.99; 83.120 English version Reinforcement Specifications for multi-axial multi-ply fabrics Part 1: Designation Renfort Spcifications pour les tissus multi-axiaux multicouches Partie 1: Dsignation Verstrkungen Spezifikation fr Multiaxialgelege Teil 1: Bezeichnung This Eu

9、ropean Standard was approved by CEN on 10 May 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references con

10、cerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own

11、language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden

12、, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

13、Ref. No. EN 13473-1:2001 EPage 2 EN 13473-1:2001 BSI 07-2001 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions 4 4 Designation . 6 4.1 General . 6 4.2 Data-Block 1 7 4.3 Data-Block 2 7 4.4 Data-Block 3 8 5 Coding examples 8 5.1 Example 1 . 8 5.2 Example 2 . 8 5.3 Ex

14、ample 3 . 9Page 3 EN 13473-1:2001 BSI 07-2001 Foreword This European Standard has been prepared by Technical Committee CEN/TC 249, Plastics, the Secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or

15、 by endorsement, at the latest by December 2001, and conflicting national standards shall be withdrawn at the latest by December 2001. This standard is one part of EN 13473, Reinforcement Specification for multi-axial multi-ply fabrics, which is constructed as follows: Part 1: Designation; Part 2: M

16、ethods of test and general requirements; Part 3: Specific requirements. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, German

17、y, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Page 4 EN 13473-1:2001 BSI 07-2001 1 Scope This part 1 of EN 13473 establishes a method of designation for multi-axial multi-ply fabrics that shall be used for specificati

18、ons for the reinforcement of materials. The method of designation defines the structure of the multi-axial multi-ply construction and the binding system. This designation system applies to multi-axial multi-ply fabrics made of reinforcement yarns, tows, rovings, fibre fleeces, films, foams or other

19、materials which are intended to provide reinforcement in composite materials and which is bound to a multi-ply construction. The designation of a multi-axial multi-ply fabric is structured in a product of multi-axial multi-ply fabrics. It is not intended that this hierarchy takes into account all th

20、e attributes of individual multi-axial multi-ply fabrics. Therefore multi-axial multi-ply fabrics having the same designation do not necessarily give the same performance. This part 1 of EN 13473 does not give engineering data, performance data or data that may be required to specify multi-axial mul

21、ti-ply fabrics for a particular application or method of processing. If such additional properties are required they have to be determined in accordance with the test methods specified in EN 13473-2. 2 Normative references This European Standard incorporates by dated or undated reference, provisions

22、 from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by ame

23、ndment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 13473-2, Reinforcement Specifications for multi-axial multi-ply fabrics Part 2: Methods of test and general requirements. ISO/DIS 1268-1:1997, Fibre-reinforced plastics Met

24、hods of producing test plates Part 1: General conditions. ISO 472, Plastics Vocabulary. ISO 1043-2, Plastics Symbols Part 2: Fillers and reinforcing materials. ISO 4921, Knitting Basic concepts Vocabulary. 3 Terms and definitions For the purposes of this European Standard, the terms and definitions

25、given in ISO 472, EN 13473-2 and the following apply. 3.1 multi-axial multi-ply (not woven) fabric textile structure constructed out of one or more laid parallel non-crimped not-woven thread plies with the possibility of different orientations, different thread densities of the single thread plies a

26、nd possible integration of fibre fleeces, films, foams or other materials, fixed by loop systems or by chemical binding systems. The threads can be oriented parallel or alternating crosswise. These products can be produced on machines with insertion devices (parallel-weft or cross-weft) and warp kni

27、tting machines or chemical binding systemsPage 5 EN 13473-1:2001 BSI 07-2001 3.2 ply construction textile structure constructed out of one or more laid parallel non-crimped thread plies, which is differently oriented, with different thread densities of the single thread plies and in which integratio

28、n of fibre fleeces, films, foams or other materials is possible. The orientation of the single thread plies is related to the production direction of 0. The description of the orientation of the thread plies is derived from ISO/DIS 1268-1:1997 using the angle orientation (90 maximum angle) which is

29、defined as follows: The thread plies oriented in the range between 0,90 are described as “+” or “-”-direction in relation to 0. The orientation is defined as “+”, if the threads are oriented in quadrant “+”, respectively “-”, if the threads are laid in quadrant “-” (see Figure 1). Key 1 y 90 2 z dir

30、ection of staple 3 x 0 direction of production Figure 1 Definition orientation of thread-direction 3.2.1 -thread thread oriented in the range between 0, 90 3.2.2 0-thread thread oriented in 0 3.2.3 cover ply additional textile or non-textile material, which is located on the surface of the ply const

31、ruction 3.2.4 inlay ply additional textile or non-textile material, which is located between the single plies of the ply constructionPage 6 EN 13473-1:2001 BSI 07-2001 3.3 binding system fixing mechanism of the ply construction including cover and/or inlay by loop or chemical binding systems 3.3.1 l

32、oop according to ISO 4921 3.3.2 chemical binding fixing by chemical means of adhesive binder 4 Designation 4.1 General The designation for multi-axial multi-ply fabrics is based on the following standardized pattern. This standardized pattern is a modification of the frame text given in ISO 1043-2,

33、adapted to the designation of the multi-axial multi-ply fabrics. Table 1 Designation system Designation Identity-Block Individual-Item-Block International Standard Data-Block 1 Data-Block 2 Data-Block 3 Example EN 13473-1, . . . The design consists out of an Identity-Block comprising the European St

34、andard Numbers and an Individual- Item-Block. For unambiguous coding the Individual-Item-Block is subdivided into 3 Data-Blocks. To ensure legibility: the Individual-Item-Block shall be separated from the Identity-Block by a “comma (,)”; the 3 Data-Blocks of the Individual-Item-Block are framed by “

35、rectangular brackets (.)”; if a Data-Block is not used, this shall be indicated by empty “rectangular brackets ()”. The three Data-Blocks are comprising the following information: Data-Block 1: Identification of the ply construction ; Data-Block 2: Identification of the binding system ; Data-Block 3

36、: Identification of the multi-axial multi-ply fabric manufacturer.Page 7 EN 13473-1:2001 BSI 07-2001 4.2 Data-Block 1 This Data-Block describes the ply construction. The description of the single plies are separated by a “double slash (/)”, starting with the first ply due to the production successio

37、n (see Figure 1). Each single ply description consists out of 3 positions. The three positions of the single ply description are separated by a “comma (,)”. In position 1 of the ply description the material types and grades used in this ply are identified by code letters according to Table 2. In the

38、 case of combinations of different materials (hybrid materials), the different materials and grades have to be identified by their abbreviation with each constituent separated by a “slash (/)”. For each constituent the abbreviation shall be followed by a number equal to the percentage content by wei

39、ght rounded to the nearest 1 %. The materials need to appear in descending order of their content by weight in the single ply. Table 2 Abbreviation for materials types Code Letter Material Type AA r a m i d e C Carbon GG l a s s K Ceramic PA Polyamide PE Polyethylen PES PET Polyester/ Polyethylenter

40、ephtalat PP Polypropylene NOTE Supplements of further material types are possible. The material grades have to be aditionally specified in each case. In position 2 of the ply description the mass per unit area of the single ply is identified by a number equal to the mass in grams per square metre. P

41、osition 3 is indicating the orientation of the thread plies in case of the use of reinforcement fibres or the material description in case of the use of cover or inlay plies (see ISO 1043-2). For alternating crosswise oriented thread plies the two different orientations of the threads in one single

42、layer are described by the two thread orientations divided by a single “slash (/)”. 4.3 Data-Block 2 In this Data-Block the binding system is defined and described by 3 Positions. Positions 1, 2 and 3 are separated by a “comma (,)”. In position 1 of the binding description the material types and gra

43、des used are identified by abbreviation according to Table 2. In the case of combinations of different materials (hybrid materials), the different materials and grades shall be identified by their abbreviation with each constituent separated by a “slash (/)”. For each constituent the abbreviation sh

44、all be followed by a number equal to the percentage content by weight rounded to the nearest 1 %. The materials shall appear in descending order of their content by weight. In position 2 of the binding description the mass per unit area of the binding is identified by a number equal to the mass in g

45、rams per square metre. In position 3 of this Data-Block the binding type is identified by letters according to Table 3.Page 8 EN 13473-1:2001 BSI 07-2001 Table 3 Code letter for the type of the binding system Code letter Type of binding system L Loop system C Chemical binding system 4.4 Data-Block 3

46、 This Data-Block contents the code of the multi-axial multi-ply fabric manufacturer. 5 Coding examples 5.1 Example 1 A multi-axial multi-ply fabric is made of: E-glass reinforcement yarn; 3 plies: -45/+45/0; parallel weft; weight per 45-ply: 235 g/m 2 ; weight per 0-ply: 425 g/m 2 ; loop system, PES

47、, 12 g/m 2 ; manufacturers code X. The designation for this multi-axial multi-ply fabric is: EN 13473, G, 235, -45/G, 235, +45/G, 425, 0 PES, 12, L X 5.2 Example 2 A multi-axial multi-ply fabric is made of: 5 plies: ply 1: PE-film, 30 g/m 2 /ply 2: +55, aramide/carbon hybrid, 50/50-weight distributi

48、on, 180 g/m 2 /ply 3: 90, E-glass, 220 g/m 2 /ply 4: 30, aramid/carbon hybrid, 20/80-distribution, 210 g/m 2 /ply 5: chopped fibres, E-glass, 225 g/m 2 ; parallel weft; loop system, PES, 15 g/m 2 ; manufacturers code X. The designation of this multi-axial multi-ply fabric is: EN 13473, PE, 30, Z/A50

49、/C50, 180, +55/G, 220, 90/C80/A20, 210, -30/G, 225, F PES,15,L X. NOTE Codes like Z and F according to ISO 1043-2.Page 9 EN 13473-1:2001 BSI 07-2001 5.3 Example 3 A multi-axial multi-ply fabric is made of: E-glass reinforcement yarn; 2 plies: ply 1: 45 (cross-weft) / ply 2: +45 (cross-weft); for the cross-weft an angle deviation of 4 (depending on the processing parameter) is assumed;