BS EN 13365-2002 Transportable gas cylinders - Cylinder bundles for permanent and liquefied gases (excluding acetylene) - Inspection at time of filling《可运输气瓶 永久的和液化的气体(乙炔除外)的钢瓶组件 灌.pdf

《BS EN 13365-2002 Transportable gas cylinders - Cylinder bundles for permanent and liquefied gases (excluding acetylene) - Inspection at time of filling《可运输气瓶 永久的和液化的气体(乙炔除外)的钢瓶组件 灌.pdf》由会员分享，可在线阅读，更多相关《BS EN 13365-2002 Transportable gas cylinders - Cylinder bundles for permanent and liquefied gases (excluding acetylene) - Inspection at time of filling《可运输气瓶 永久的和液化的气体(乙炔除外)的钢瓶组件 灌.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN13365:2002 Incorporating Amendment No. 1 Transportable gas cylinders Cylinder bundles for permanent and liquefied gases (excluding acetylene) Inspection at time of filling The European Standard EN 13365:2002, with the incorporation of amendment A1:2005, has the status of a Brit

2、ish Standard ICS 23.020.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Amd. No. Date Comments 16059 22 December 2005 See national foreword BS EN 13365:2002 National foreword This British Standard is the official English language version of EN 13365:2002, including amendmen

3、t A1:2005. The start and finish of text introduced or altered by CEN amendment is indicated in the text by tags !“. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“. The UK participation in its preparation was

4、 entrusted by Technical Committee PVE/3, Gas containers, to Subcommittee PVE/3/7, Gas cylinder (receptacle) operations, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals

5、 for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement internation

6、al or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to

7、 include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, page

8、s 2 to 8, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication This British Standard was published under the authority of the Standards Policy and Strategy Committee on 18 April 2002

9、BSI 22 December 2005 ISBN 0 580 39505 7 EUROPEAN STANDARD NORME EUROPENNE EN 13365 March 2002 + A1EUROPISCHE NORM September 2005 ICS 23.020.30 English version Transportable gas cylinders - Cylinder bundles for permanent and liquefied gases (excluding acetylene) - Inspection at time of filling (inclu

10、des amendment A1:2005) Bouteilles gaz transportables - Cadres de bouteilles pour gaz permanents et liqufis (sauf lactylne) - Inspection au moment du remplissage (inclut lamendement A1:2005) Ortsbewegliche Gasflaschen - Flaschenbndel fr permanente und verflssigte Gase (auer Acetylen) - Prfung zum Zei

11、tpunkt des Fllens (enthlt nderung A1:2005) This European Standard was approved by CEN on 30 December 2001. Amendment A1 was approved by CEN on 22 July 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the

12、status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A

13、 version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Es

14、tonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMI T EUROP EN D E NORMALI S ATI O N EURO

15、P I S CHES KOMI TEE F R NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13365:2002 + A1:2005 E EN 13365:2002 (E) Contents page Foreword3 Introduction .4 1 Scope 5

16、2 Normative references 5 3 Terms and definitions .5 4 Inspection at time of filling 6 Bibliography 8 2 EN 13365:2002 (E) 3 Foreword This document EN 13365:2002 has been prepared by Technical Committee CEN/TC 23 “Transportable gas cylinders“, the secretariat of which is held by BSI. This European Sta

17、ndard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2002, and conflicting national standards shall be withdrawn at the latest by September 2002. According to the CEN/CENELEC Internal Regulations, the nationa

18、l standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdo

19、m. Foreword to amendment A1 This European Standard (EN 13365:2002/A1:2005) has been prepared by Technical Committee CEN/TC 23 “Transportable gas cylinders”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an i

20、dentical text or by endorsement, at the latest by March 2006, and conflicting national standards shall be withdrawn at the latest by March 2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Sta

21、ndard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 13365:2002 (E) 4 I

22、ntroduction Transportable gas cylinder bundles require inspection at time of filling, both before and after the filling process, in order to ensure that all components are suitable for the intended filling conditions and are free of serious defects and contamination that can affect the integrity of

23、the bundle. EN 13365:2002 (E) 5 1 Scope This European Standard specifies the requirements for inspection before, during and after the time of filling for cylinder bundles, also referred to as bundles. This standard does not apply to acetylene bundles which are covered in EN 12755. This standard does

24、 not cover bundles when they are a part of a battery vehicle. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed here

25、after. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 1802, Tra

26、nsportable gas cylinders Periodic inspection and testing of seamless aluminium alloy gas cylinders. EN 1968, Transportable gas cylinders Periodic inspection and testing of seamless steel gas cylinders. prEN 13769, Transportable gas cylinders Cylinder bundles Design, manufacture, identification and t

27、esting. prEN ISO 11623, Transportable gas cylinders Periodic inspection and testing of composite gas cylinders (ISO/FDIS 11623:2000). 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 cylinder bundle (bundle) transportable assembly, wh

28、ich is designed for being routinely lifted and which consists of a frame and two or more cylinders each of capacity up to 150 litres connected to a manifold by cylinder valves or fittings such that the cylinders are filled, transported and emptied without disassembly 3.2 frame structural and non str

29、uctural members of a bundle which combine all other components together, whilst providing protection for the bundles cylinders, valves and manifold and which enable the bundle to be transported 3.3 cylinder valve valve which is fitted into a cylinder and to which a manifold is connected 3.4 cylinder

30、 fitting device with no gas shut-off capability which serves as a method for connecting the manifold of a bundle to its individual cylinders when cylinder valves are not fitted to the cylinders 3.5 manifold system for connecting the cylinder valves or cylinder fittings to the main outlet valve(s) or

31、 outlet connection(s) of the bundle EN 13365:2002 (E) 6 3.6 main outlet valve valve which is fitted to the manifold of the bundle isolating it from the outlet connection(s) 3.7 liquefied gas gas which has a critical temperature of 20 oC or above 3.8 maximum permissible filling weight the product of

32、the minimum guaranteed water capacity of the cylinders of the cylinder bundle and the filling ratio of the gas contained 4 Inspection at time of filling 4.1 Inspection prior to filling Before filling a bundle it shall be verified by visual examination that: the bundle is permitted to be filled in th

33、e country of the filling station; the bundle has an unexpired periodic inspection date; the bundle is compatible with the nature of the gas and filling pressure or filling weight; the frame is free from damage which may affect its mechanical integrity; the restraining systems that prevent the cylind

34、ers from moving are secure and the cylinders have not moved whilst in service; any lifting attachments and/or fork lift slots are free from damage, that may affect the integrity of the bundle; the manifold and pipework are securely attached to the frame and are undamaged; flexible hoses, where fitte

35、d, are free from damage to any reinforcement braiding; the visible surfaces of the cylinders are free from any signs of dents, cuts, gouges, fire damage or any other signs of damage. Rejection criteria shall be applied in accordance with EN 1968, EN 1802 or prEN ISO 11623, as appropriate. Where any

36、cylinder is damaged the cylinder bundle shall not be filled but shall be identified and shall be removed from service for corrective action. In the case of fire damage the bundle shall be disassembled and all cylinders shall be inspected and any suspect cylinders shall be revalidated or rejected; th

37、e bundle does not show any signs of having been immersed in water or other liquids (e.g. cylinders covered in mud or seaweed) or any signs of tampering (e.g. loosened bolts, missing panels); the cylinder valves if fitted are all in the open position; the main outlet valve is free from contamination

38、and is undamaged and is the correct thread for the gas to be filled; where appropriate any safety devices such as relief valves or bursting discs are in place and have not been damaged; the necessary data specified in prEN 13769 is permanently marked or labelled on the bundle; in the case of liquefi

39、ed gases the tare weight and maximum permissible filling weight are legible. Additionally a check of the main outlet valve shall be carried out to ensure that the valve operates properly. EN 13365:2002 (E) 7 Before filling it shall be verified that the bundle is free from any internal contamination

40、which may affect its integrity by ensuring that the bundle has a positive residual pressure and, for liquefied gases, by checking the weight against the tare weight of the bundle. 4.2 Inspection during filling During filling of the bundle it shall be verified that no apparent leaks exist. Particular

41、 attention shall be paid to bundles containing toxic, flammable or pyrophoric gases. ! For bundles for liquefied gases equipped with closable cylinder valves, in order to ensure that no individual cylinder within the bundle or the bundle as a whole is overfilled, either all cylinders of a bundle sha

42、ll be dismantled and only each cylinder may be individually filled at a time, or each cylinder in a bundle shall be equipped with a filling control device to ensure that they are not overfilled.“ 4.3 Inspection after filling Upon completion of the filling of the bundle it shall be verified that: ! t

43、he bundle and no single cylinder with a closable cylinder valve has been overfilled.“ For bundles filled by pressure the pressure shall be corrected against the reference temperature. For bundles filled by weight, the weight of the full bundle shall be checked against the maximum permissible weight

44、by the use of a scale suitable for the weight of the bundle; the cylinder bundle has been correctly labelled; the main outlet valve is not leaking; no apparent leaks exist from the bundle; cylinder valves that need to be closed for transport in accordance with transport regulations, have been closed

45、. EN 13365:2002 (E) 8 Bibliography EN 12755, Transportable gas cylinders Filling conditions for acetylene bundles. blank BS EN 13365:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It pr

46、esents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of

47、BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20

48、 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Cust

49、omer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library