BS EN 13126-16-2008 Building hardware - Requirements and test methods for windows and doors height windows - Hardware for Lift&Slide windows and doors《建筑五金件 窗和门上窗的要求和试验方法 上下移动和推拉式门.pdf

《BS EN 13126-16-2008 Building hardware - Requirements and test methods for windows and doors height windows - Hardware for Lift&Slide windows and doors《建筑五金件 窗和门上窗的要求和试验方法 上下移动和推拉式门.pdf》由会员分享，可在线阅读，更多相关《BS EN 13126-16-2008 Building hardware - Requirements and test methods for windows and doors height windows - Hardware for Lift&Slide windows and doors《建筑五金件 窗和门上窗的要求和试验方法 上下移动和推拉式门.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 13126-16:2008Building hardware Requirements and test methods for windows and doors height windows Part 16: Hardware for Lift active sash shall function correctly. NOTE After the sliding operation crash-test all adjustment possibilities may be used to operate the sash. BS EN 131

2、26-16:2008EN 13126-16:2008 (E) 9 5.2.3 Minimum closing device resistance 5.2.3.1 Hardware without tilt function The closing device shall withstand a torque Thr, which is the threefold torque Thas calculated and recorded in accordance with 5.2.1. For example: length of the handle = 220 mm operative l

3、ength (key 4, Figure 1) = 220 mm 20 mm = 200 mm torque Th = operative length X force F = 200 mm X 100 N = 20 Nm torque Thr= 3 X Th = 3 X 20 Nm = 60 Nm NOTE Hardware with tilt function without positive control should also conform to this requirement. Upon completion of the test in accordance with 7.5

4、.1, the closing device shall operate. 5.2.3.2 Hardware with tilt function and with positive control The hardware shall withstand a torque Thr, which is the threefold torque Thas calculated and recorded in accordance with 5.2.1. For example: length of the handle = 220 mm operative length (key 4, Figu

5、re 1) = 220 mm 20 mm = 200 mm torque Th = operative length X force F = 200 mm X 100 N = 20 Nm torque Thr= 3 X Th = 3 X 20 Nm = 60 Nm Upon completion of the test in accordance with 7.5.2.1 and 7.5.2.2, the closing device shall operate. 5.2.4 Resistance to additional loading After the additional loadi

6、ng test in accordance with 7.6 the active sash shall not drop and shall still be constrained by its fixings. NOTE It is not necessary for the sash to operate during and after the additional loading test. 5.2.5 Static endurance test at ambient temperature An additional endurance test at ambient tempe

7、rature in accordance with 7.7 is required. Before and upon completion of the endurance test in accordance with 7.7, no roll shall deviate by more than 0,5 % of its initial diameter. 6 Test equipment 6.1 General The specimen shall be installed in a test rig for testing as specified in Figure A.1 in a

8、ccordance with the manufacturers fixing instructions. All tolerances shall be %30+unless otherwise specified. BS EN 13126-16:2008EN 13126-16:2008 (E) 10 6.2 Specimen Hardware sets for Lift maximum sash dimensions (in accordance with the manufacturers product documentation) number and location of loc

9、king points. The specimen to be tested shall correspond in function, shape and material for which the hardware is intended. The dimensions of the specimen shall conform to 4.10. The hardware tested should be in accordance with the manufacturers recommendations for size and mass of the test specimen.

10、 7 Test procedure 7.1 Samples Four samples shall be tested in accordance with this part of this European Standard: sample A1 durability test sample A2 static endurance test at ambient temperature sample B corrosion test sample C retained for reference control NOTE 1 Alternatively sample A1 and A2 ma

11、y be the same. NOTE 2 Sample B should only be necessary if no test report can be supplied by the manufacturer regarding the testing of the hardware component or set in accordance with EN 1670. NOTE 3 Sample C should be retained by the test institute for the duration of the validity of the test repor

12、t. 7.2 Procedure Use sample A1. Inspect the rolls for surface imperfections. Inspect and ensure that the installed hardware set is in accordance with the manufacturers instructions. Install the hardware for Lift the procedure is as follows: initial position of the active sash is the locked closed po

13、sition. hardware is moved jerk and jolt-free into an operating position, in which the tilted position is reached. In this position the sash remains for 1 s so that it can settle. hardware is brought back to the initial position; this is the locked closed position. Then the hardware remains in this i

14、nitial position for 1 s and can settle before the next test cycle is started. NOTE The velocity with which the hardware is operated results from the predetermined rate of 200 cycle/h, the indicated interval times and the jerk and jolt-free initiation of all movements. 7.3.1.1.2 Tilt cycles on hardwa

15、re without positive control Tilt cycles for hardware with tilt function and without positive control shall be at a rate (rate) of 200 cycles/h; the procedure shall be as follows: initial position of the active sash is the locked closed position. BS EN 13126-16:2008EN 13126-16:2008 (E) 12 hardware is

16、 moved into an operating position, in which the tilted position can be enabled. active sash is moved jerk and jolt-free into the tilting position from the closed position. The sash shall freefall into the tilt position; (for example the pneumatic cylinder is decoupled or the valves open before the f

17、inal tilt position). 5 mm before the final tilt position, the velocity shall be 0,5 m/s ( 10 %). In the tilt position the active sash is held by the scissors-stay arm(s). The sash remains for 1 s in this position to allow it to settle. active sash is brought back to the initial position, whereby the

18、 locked closed position is reached again; the initiation of movement shall be jerk and jolt-free. The hardware then remains in the initial position for 1 s before the next test cycle is started. NOTE Unless otherwise stated, the velocity with which the hardware is operated results from the predeterm

19、ined rate of 200 cycle/h, the indicated interval times and the jerk and jolt-free initiation of all movements. 7.3.1.2 Lifting cycles Lifting cycles shall be at a rate of 200 cycles/h; the procedure shall be as follows: active sash shall be in the locked closed position. lifting action is started vi

20、a the hardware in a jerk and jolt-free manner, whereby the active sash is brought into the sliding position. The sash remains in this position for 1 s, so that it can settle. active sash is moved in the sliding position in the direction of the opening position in such a manner that it comes to a hal

21、t 3 mm before the locking position. The sash remains in this position for 1 s, so that it can settle. active sash is brought back to the initial position via the hardware, in doing so the locked closed position is reached again; the initiation of movement shall be jerk and jolt-free. The hardware th

22、en remains in the initial position for 1 s, before the next test cycle is started. NOTE 1 Unless otherwise stated, the velocity with which the hardware is operated results from the predetermined rate of 200 cycle/h, the indicated interval times and the jerk and jolt-free initiation of all movements.

23、 NOTE 2 Hardware systems, where the sash itself is not lifted but a gasket mechanism is moved, should be tested with the gasket mechanism moved. BS EN 13126-16:2008EN 13126-16:2008 (E) 13 7.3.1.3 Sliding cycles Sliding cycles shall be at a rate of 200 cycles/h; the procedure shall be as follows: ini

24、tial position of the active sash is in the closed position. movement range results from the sash width of the testing-element minus 200 mm (for example: a sash width of 1 200 mm results in a movement range of 1 000 mm). active sash is moved along a predetermined movement range while in the sliding p

25、osition, and remains there for 1 s at the end of the movement range. Both the acceleration from the initial sliding position, as well as braking at the end of the movement range shall be in a jerk and jolt-free manner. active sash is brought back to the initial position, whereby the closed position

26、is reached again; the initiation of movement shall be jerk and jolt-free. The sash shall freefall into the locked position; (for example: the pneumatic cylinder is decoupled 100 mm before the final tilt position / or the valves open). The hardware then remains in the initial position for 1 s, allowi

27、ng it to settle before the next test cycle is started. NOTE The velocity with which the hardware is operated results from the predetermined rate of 200 cycle/h, the indicated interval times and the jerk and jolt-free initiation of all movements. 7.3.1.4 Total cycles (lifting and sliding cycles) 7.3.

28、1.4.1 General Lifting cycles in accordance with 7.3.1.2 and sliding cycles in accordance with 7.3.1.3 may be combined to result in total cycles. No individual steps should be repeated during the total cycles. 7.3.1.4.2 Description of the Total cycles (lifting and sliding) Total cycles shall be at a

29、rate of 100 cycles/h. The procedure shall be as follows: initial position of the active sash is the locked closed position. lifting action shall be initiated by the hardware, whereby the active sash is brought into the locking position in a jerk and jolt-free manner. In this position the sash remain

30、s for 1 s so that it can settle. movement range results from the sash width of the testing-element minus 200 mm (for example: a sash width of 1200 mm results in a movement range of 1000 mm). active sash is moved along a predetermined movement range in the sliding position, and remains there for 1 s

31、at the end of the movement range. Both the acceleration from the initial sliding position, as well as braking at the end of the movement range shall be in a jerk and jolt-free manner. active sash is moved back in the direction of the closed position so that it comes to a halt 3 mm before the closed

32、position in a jerk and jolt-free manner. The initiation of movement shall also be in a jerk and jolt-free manner. active sash is brought back to the initial position via the hardware, whereby the locked closed position is reached again; the initiation of movement shall be jerk and jolt-free. The har

33、dware then remains in the initial position for 1 s, before the next test cycle is started. NOTE The velocity with which the hardware is operated results from the predetermined rate of 100 cycle/h, the indicated interval times and the jerk and jolt-free initiation of all movements. BS EN 13126-16:200

34、8EN 13126-16:2008 (E) 14 7.3.2 Acceptance criteria 7.3.2.1 Handle operation tolerance Check that the specimen functions correctly in accordance with 5.2.1, whereby the calculated torque Th shall not be exceeded. NOTE In general, torques are measured during normal hardware operation. During the durab

35、ility tests, higher torques may be necessary due to the higher operating velocity 7.3.2.2 Further acceptance criteria The active sash shall function correctly NOTE In general, these two acceptance criteria (7.3.2.1 and 7.3.2.2) should be checked after each 5 000 cycles, and upon completion of the ti

36、lting cycles in accordance with 7.3.1.1, the lifting cycles in accordance with 7.3.1.2 and the sliding cycles in accordance with 7.3.1.3. or the total cycles in accordance with 7.3.1.4. 7.4 Sliding operation crash-tests 7.4.1 Procedure into the closed position Use sample A1. The active sash mass sha

37、ll be reduced to 50 % of the maximum test mass. Move the active sash away from the opening position towards the closed position, whereby the acceleration shall be in a jerk and jolt-free manner. 100 mm before reaching the closed position, the active sash shall have a velocity of 0,8 m/s. After havin

38、g reached the closed position, the active sash is allowed to settle. Test the sash 3 times. NOTE 1 After having reached the closed position, the sash can be in the sliding, tilted or closed position while settling. NOTE 2 If the hardware is equipped with a brake mechanism, the velocity of the active

39、 sash while moving the 100 mm up to the closed position may be reduced during cycling. NOTE 3 If the active sash reaches the tilted position instead of the closed position, it should be tested in accordance with the previous procedure. In this case the closed position should be replaced by the tilte

40、d position. 7.4.2 Procedure into the opening position Use sample A1. This procedure shall use an active sash test mass of 50 % of the maximum test mass. The active sash is moved away from the closed position towards the opening position, whereby the acceleration shall be in a jerk and jolt-free mann

41、er to 100 mm before reaching the opening position. The active sash shall have a velocity of 0,8 m/s. The sash shall collide with the buffer stop at a speed of 0,8 m/s (see Figure A.2). After the active sash collides with the buffer stop, the active sash is allowed to settle. Test the sash 3 times. N

42、OTE If the hardware is equipped with a brake mechanism, the velocity of the active sash while moving the 100 mm up to the opening position may be reduced during cycling. BS EN 13126-16:2008EN 13126-16:2008 (E) 15 7.4.3 Acceptance criteria Upon completion of the test in accordance with 7.4.1 and 7.4.

43、2, the hardware shall conform to 5.2.2 and the following: active sash shall not drop and shall still be constrained by its fixings; active sash shall function correctly. NOTE After the sliding operation tests all adjustment possibilities may be used to operate the sash. 7.5 Minimum closing device re

44、sistance test 7.5.1 Hardware without tilt-function The locking mechanism (espagnolette, window handle, handle-lever, gear) shall be inserted in a testing-rig that blocks the locking mechanism transmission. For example in the case of an espagnolette, the face-plate and runner-bead shall be blocked us

45、ing a clamping-device. Exert the torque Thr, calculated and recorded in accordance with 5.2.3.1, on the locking mechanism and maintain it for 10 s 20+s. Upon completion of this exerted torque, the closing device shall operate in accordance with 5.2.3.1. NOTE 1 If handles are used that can only trans

46、mit a certain limited torque (i.e. equipped with breaking point, spindle twists etc.), they should be tested at the maximum operational torque for which they have been designed. NOTE 2 The results of the tests should be submitted by the hardware manufacturer by a self declaration with supporting doc

47、umentation to the test house. 7.5.2 Hardware with tilt-function with positive control 7.5.2.1 Procedure - in the tilted position Use sample A1. The active sash is blocked on top in the tilt position in accordance with Figure A.3, so that the active sash cannot freefall back into the locking position

48、. Apply the torque Thr,calculated and documented in accordance with 5.2.3.2, to the espagnolette and maintain it for 10 s 20+. Upon completion of this force and removal of the blocking, the hardware shall function correctly in accordance with 5.2.3.2. NOTE If handles are used that can only transmit

49、a certain limited torque (i.e. equipped with breaking point, spindle twists etc.), they should be tested at the maximum operational torque for which they have been designed. 7.5.2.2 Procedure - in the closed position Use sample A1. The active sash is blocked on top in the locked position in accordance with Figure A.4, so that the active sash cannot freefall back into the tilted position. Apply the torque Thrcalculated and documented in accordance with 5.2.3.2 to the espagnolette and maintain it for 10 s 20+. Upo