BS EN 12150-1-2015 Glass in building Thermally toughened soda lime silicate safety glass Definition and description《建筑物用玻璃 热钢化钠钙安全玻璃 定义和说明》.pdf

《BS EN 12150-1-2015 Glass in building Thermally toughened soda lime silicate safety glass Definition and description《建筑物用玻璃 热钢化钠钙安全玻璃 定义和说明》.pdf》由会员分享，可在线阅读，更多相关《BS EN 12150-1-2015 Glass in building Thermally toughened soda lime silicate safety glass Definition and description《建筑物用玻璃 热钢化钠钙安全玻璃 定义和说明》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 12150-1:2015Glass in building Thermallytoughened soda lime silicatesafety glassPart 1: Definition and descriptionBS EN 12150-1:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12150-1:2015.It supersedes BS EN 12150-1:2000 which

2、 is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/520/1, Basic and transformed glass products.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovi

3、sions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 77022 7ICS 81.040.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published

4、under the authority of theStandards Policy and Strategy Committee on 30 September 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 12150-1:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12150-1 September 2015 ICS 81.040.20 Supersedes EN 12150-1:2000Engli

5、sh Version Glass in building - Thermally toughened soda lime silicate safety glass - Part 1: Definition and description Verre dans la construction - Verre de silicate sodo-calcique de scurit tremp thermiquement - Partie 1: Dfinition et description Glas im Bauwesen - Thermisch vorgespanntes Kalknatro

6、n-Einscheiben-Sicherheitsglas - Teil 1: Definition und Beschreibung This European Standard was approved by CEN on 8 August 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standar

7、d without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any

8、other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republ

9、ic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN C

10、OMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12150-1:2015 EBS EN 12

11、150-1:2015EN 12150-1:2015 (E) 2 Contents Page European foreword . 4 Introduction 5 1 Scope 6 2 Normative references 6 3 Terms and definitions . 6 4 Glass products 8 5 Fracture characteristics 8 6 Dimensions and tolerances . 9 6.1 Nominal thickness and thickness tolerances 9 6.2 Width and length (siz

12、es) . 9 6.2.1 General 9 6.2.2 Maximum and minimum sizes . 10 6.2.3 Tolerances and squareness 10 6.2.4 Edge deformation produced by the vertical process 11 6.3 Flatness 11 6.3.1 General . 11 6.3.2 Measurement of overall bow . 13 6.3.3 Measurement of wave and roller wave 14 6.3.4 Measurement of edge l

13、ift (for horizontally toughened glass only) 15 6.3.5 Measurement of perimeter deformation of glass produced by air cushion toughening process . 16 6.3.6 Measurement of local distortion (for vertically toughened glass only) . 17 6.3.7 Limitation on overall bow, roller waves and edge lift for horizont

14、ally toughened glass . 17 6.3.8 Limitation on overall bow, wave and perimeter deformation for toughened glass manufactured by air cushion process. 18 6.3.9 Limitation on overall bow and local distortion for vertically toughened glass. 19 6.3.10 Other distortions 19 7 Edge and/or surface work, holes,

15、 notches and cut-outs 20 7.1 Warning . 20 7.2 Edge working of glass for toughening . 20 7.3 Profiled edges 21 7.4 Round holes 21 7.4.1 General . 21 7.4.2 Diameter of holes . 21 7.4.3 Limitations on position of holes . 21 7.4.4 Tolerances on hole diameters . 22 7.4.5 Tolerances on position of holes 2

16、3 7.5 Holes/others 23 7.6 Notches and cut-outs . 24 7.7 Shaped panes . 24 8 Fragmentation test 24 BS EN 12150-1:2015EN 12150-1:2015 (E) 3 8.1 General . 24 8.2 Dimensions and number of test specimens 24 8.3 Test procedure 24 8.4 Assessment of fragmentation . 25 8.5 Minimum values from the particle co

17、unt . 26 8.6 Selection of the longest particle 27 8.7 Maximum length of longest particle 27 9 Other physical characteristics . 27 9.1 Optical distortion 27 9.1.1 Thermally toughened soda lime silicate safety glass produced by vertical toughening 27 9.1.2 Thermally toughened soda lime silicate safety

18、 glass produced by horizontal toughening 27 9.2 Anisotropy (iridescence) . 27 9.3 Thermal durability . 27 9.4 Mechanical strength 28 9.5 Classification of performance under accidental human impact 28 10 Marking 28 Annex A (informative) Curved thermally toughened soda lime silicate safety glass 30 An

19、nex B (informative) Alternative method for the measurement of roller wave distortion . 31 B.1 Apparatus 31 B.2 Method 31 B.3 Limitations 32 B.4 Alternative use of apparatus 32 Annex C (informative) Examples of particle count 33 Annex D (informative) Risk of spontaneous breakage of toughened glass du

20、e to nickel sulfide inclusion 36 Bibliography . 37 BS EN 12150-1:2015EN 12150-1:2015 (E) 4 European foreword This document (EN 12150-1:2015) has been prepared by Technical Committee CEN/TC 129 “Glass in building”, the secretariat of which is held by NBN. This European Standard shall be given the sta

21、tus of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall be withdrawn at the latest by March 2016. Attention is drawn to the possibility that some of the elements of this document may be the subjec

22、t of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12150-1:2000. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. EN 12150, Gla

23、ss in building Thermally toughened soda lime silicate safety glass, consists of the following parts: Part 1: Definitions and description; Part 2: Evaluation of conformity/Product standard. This European Standard differs from EN 12150-1:2000 as follows: a) some figures have been revised and some new

24、figures have been added; b) new terms and definitions have been included in Clause 3, e.g. air cushion process (3.6), edge lift (3.9) and roller wave distortion (3.13); c) further nominal thicknesses have been included in Table 1; d) Subclause 6.2.3 “Tolerances and squareness” has been completely re

25、vised; the squareness of rectangular glass panes is now expressed by the difference between its diagonals; e) Clauses 6 and 7 have been completely revised (including the air cushion manufacturing process); f) the normative annex “Determination of U value” has been deleted; g) a new informative annex

26、 dealing with an alternative method for the measurement of roller wave distortion has been added. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyp

27、rus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the Unite

28、d Kingdom. BS EN 12150-1:2015EN 12150-1:2015 (E) 5 Introduction Thermally toughened soda lime silicate safety glass has a safer breakage behaviour when compared with annealed glass. When it should be used to offer protection under accidental human impact, thermally toughened soda lime silicate safet

29、y glass also should be classified according to EN 12600. NOTE CEN/TC 129/WG 8 is producing standards for the determination of the design strength of glass and is preparing a design method. BS EN 12150-1:2015EN 12150-1:2015 (E) 6 1 Scope This European Standard specifies tolerances, flatness, edgework

30、, fragmentation and physical and mechanical characteristics of monolithic flat thermally toughened soda lime silicate safety glass for use in buildings. Information on curved thermally toughened soda lime silicate safety glass is given in Annex A, but this product does not form part of this European

31、 Standard. Other requirements, not specified in this European Standard, can apply to thermally toughened soda lime silicate safety glass which is incorporated into assemblies, e.g. laminated glass or insulating glass units, or undergo an additional treatment, e.g. coating. The additional requirement

32、s are specified in the appropriate glass product standard. Thermally toughened soda lime silicate safety glass, in this case, does not lose its bending strength characteristics and its resistance to temperature differentials. Surface finished glasses (e.g. sandblasted, acid etched) after toughening

33、are not covered by this European Standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of t

34、he referenced document (including any amendments) applies. EN 572-1, Glass in building Basic soda lime silicate glass products Part 1: Definitions and general physical and mechanical properties EN 572-2, Glass in building Basic soda lime silicate glass products Part 2: Float glass EN 572-4, Glass in

35、 building Basic soda lime silicate glass products Part 4: Drawn sheet glass EN 572-5, Glass in building Basic soda lime silicate glass products Part 5: Patterned glass EN 572-8, Glass in building Basic soda lime silicate glass products Part 8: Supplied and final cut sizes EN 1096-1, Glass in buildin

36、g Coated glass - Part 1: Definitions and classification EN 1288-3, Glass in building Determination of the bending strength of glass Part 3: Test with specimen supported at two points (four point bending) EN 14428, Shower enclosures Functional requirements and test methods 3 Terms and definitions For

37、 the purposes of this document, the following terms and definitions apply. 3.1 thermally toughened soda lime silicate safety glass thermally toughened safety glass glass within which a permanent surface compressive stress, additionally to the basic mechanical strength, has been induced by a controll

38、ed heating and cooling process in order to give it greatly increased resistance to mechanical and thermal stress and prescribed fragmentation characteristics BS EN 12150-1:2015EN 12150-1:2015 (E) 7 Note 1 to entry: The mechanical properties, i.e. thermal durability and mechanical strength, and safet

39、y properties, i.e. fragmentation characteristics, are generated by the level of surface compression. These properties are not size dependent. 3.2 flat thermally toughened soda lime silicate safety glass thermally toughened soda lime silicate safety glass which has not been deliberately given a speci

40、fic profile during manufacture 3.3 curved thermally toughened soda lime silicate safety glass thermally toughened soda lime silicate safety glass which has been deliberately given a specific profile during manufacture Note 1 to entry: See Annex A. 3.4 enamelled thermally toughened soda lime silicate

41、 safety glass thermally toughened soda lime silicate safety glass which has a ceramic frit fired into the surface during the toughening process Note 1 to entry: After toughening the ceramic frit becomes an integral part of the glass. Note 2 to entry: In the UK, this glass is also known as opaque the

42、rmally toughened soda lime silicate safety glass. Note 3 to entry: The application of the ceramic frit may be by a continuous process or discontinuous application, e.g. screen printing. The enamelled surface could be partially or wholly. 3.5 horizontal process process in which the glass is supported

43、 on horizontal rollers 3.6 air cushion process process in which the glass is supported by an air cushion with or without additional rollers Note 1 to entry: In this process the glass will be between horizontal and 45 of horizontal. 3.7 vertical process process in which the glass is suspended by tong

44、s 3.8 edge deformation deformation of the edge cause by the tong marks for vertically toughened glass 3.9 edge lift distortion produced in horizontal toughened glass, at the leading and trailing edge of the plate 3.10 perimeter deformation distortion around the edge of toughened glass manufactured b

45、y air cushion process BS EN 12150-1:2015EN 12150-1:2015 (E) 8 3.11 local distortion local deformation of vertically toughened glass underneath the tong marks 3.12 overall bow deformation of the whole pane of toughened glass caused by the heating and cooling process 3.13 roller wave distortion distor

46、tion produced in horizontally toughened glass as a result of the glass during toughening process being in contact with the rollers 3.14 wave distortion distortion produced in air cushioned toughened glass as a result of the glass toughening process 4 Glass products Thermally toughened soda lime sili

47、cate safety glass is made from a monolithic glass generally corresponding to one of the following standards: soda lime silicate glass according to EN 572-1; float glass according to EN 572-2; drawn sheet glass according to EN 572-4; patterned glass according to EN 572-5; supplied and final cut sizes

48、 according to EN 572-8; coated glass according to EN 1096-1. Glass of nominal thicknesses other than those covered in the above standards is possible. 5 Fracture characteristics The fracture characteristics of thermally toughened soda lime silicate safety glass are directly related to the amount of

49、surface compression. These properties are not size dependent. When the thermally toughened soda lime silicate safety glass is manufactured with the correct degree of surface compression then in the event of breakage thermally toughened soda lime silicate safety glass fractures into numerous small pieces, the edges of which are generally blunt. NOTE 1 The degree of surface compression required is dependent upon glass type and thickness. NOTE 2 The fracture characteristics of glass are unaffected by temperatures between 50 C and +