BS EN 10132-4-2000 Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Spring steels and other applications《热处理用冷轧窄钢条 技术交付条件 弹簧钢和其它应用钢》.pdf

《BS EN 10132-4-2000 Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Spring steels and other applications《热处理用冷轧窄钢条 技术交付条件 弹簧钢和其它应用钢》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10132-4-2000 Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Spring steels and other applications《热处理用冷轧窄钢条 技术交付条件 弹簧钢和其它应用钢》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 10132-4:2000 The Eu

2、ropean Standard EN 10132-4:2000 has the status of a British Standard ICS 77.140.25 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Cold rolled narrow steel strip for heat treatment Technical delivery conditions Part 4: Spring steels and other applicationsThis British Standard,

3、 having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 May 2000 BSI 05-2000 ISBN 0 580 35853 4 BS EN 10132-4:2000 Amendments issued since publication Amd. No. Date Comments National forew

4、ord This British Standard is the official English language version of EN 10132-4:2000. Together with BS EN 10132-1, it supersedes BS 5770 Parts 1,2, and 3:1981. The UK participation in its preparation was entrusted to Technical Committee ISE/31, Wrought steels, which has the responsibility to: aid e

5、nquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented

6、on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Ind

7、ex”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself c

8、onfer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 14, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.EUROPEAN STAN

9、DARD NORME EUROPENNE EUROPISCHE NORM EN 10132-4 February 2000 ICS 77.140.10; 77.140.25; 77.140.50 English version Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 4: Spring steels and other applications Feuillards lamins froid pour traitement thermique - Condi

10、tions techniques de livraison - Partie 4: Aciers ressorts et autres applications Kaltband aus Stahl fr eine Wrmebehandlung - Technische Lieferbedingungen - Teil 4: Federsthle und andere Anwendungen This European Standard was approved by CEN on 3 January 2000. CEN members are bound to comply with the

11、 CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or

12、 to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versi

13、ons. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN D

14、E NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10132-4:2000 EPage 2 EN 10132-4:2000 BSI 05-2000 Contents Page Foreword 3

15、1 Scope 4 2 Normative references 4 3 Terms and definitions 4 4 Classification and designation 4 4.1 Classification 4 4.2 Designation 4 5 Information to be supplied by the purchaser 4 6 Manufacturing process 5 7 Requirements 5 7.1 General 5 7.2 Method of delivery 5 7.3 Delivery condition 5 7.4 Chemic

16、al composition 5 7.5 Mechanical properties 5 7.6 Structure 6 7.7 Surface finish 6 7.8 Dimensions and tolerances on dimensions and shape 6 8 Inspection 6 9 Sampling 7 10 Test methods 7 11 Labelling, packaging and protection 7 12 Retests 7 Annex A (informative): Technical information on steels for spr

17、ings 11 and other applications Annex B (informative): List of corresponding former national designations 14Page 3 EN 10132-4:2000 BSI 05-2000 Foreword This European Standard has been prepared by Technical Committee ECISS/TC 23, Steels for heat treatment, alloy steels and free-cutting steels - Qualit

18、ies and dimensions, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2000, and conflicting national standards shall be withdrawn at the latest by Aug

19、ust 2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, N

20、orway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. The European Standard EN 10132, Cold rolled narrow steel strip for heat-treatment - Technical delivery conditions, is subdivided as follows: Part 1: General; Part 2: Case hardening steels; Part 3: Steels for quenching and tempering;

21、 Part 4: Spring steels and other special applications.Page 4 EN 10132-4:2000 BSI 05-2000 1 Scope 1.1 This part of EN 10132 applies to: non-alloy and alloy cold rolled narrow steel strip thicknesses up to 6 mm; non-alloy and alloy cold rolled narrow steel strip in the quenched and tempered condition

22、in thicknesses between 0,30 mm and 3,00 mm for springs and for other special applications. 1.2 This EN 10132-4 is complemented by EN 10132-1. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are c

23、ited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edit

24、ion of the publication referred to applies. EN 10020, Definition and classification of grades of steel. EN 10132-1, Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 1: General. EN ISO 6508-1, Metallic materials - Rockwell hardness test - Part 1: Test method (s

25、cales A, B, C, D, E, F, G, H, K, N, T) (ISO 6508-1:1999). 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 10132-1 apply. 4 Classification and designation 4.1 Classification All steels covered by this European Standard are classified according to EN 10

26、020. Steel grades C55S, C60S, C67S, C75S, C85S, C90S, C100S and C125S are non-alloy special steels, steel grades 48Si7, 56Si7, 51CrV4, 80CrV2, 75Ni8, 125Cr2 and 102Cr6 are alloy special steels. 4.2 Designation See EN 10132-1. 5 Information to be supplied by the purchaser See EN 10132-1.Page 5 EN 101

27、32-4:2000 BSI 05-2000 6 Manufacturing process See EN 10132-1. 7 Requirements 7.1 General See EN 10132-1. 7.2 Method of delivery See EN 10132-1. 7.3 Delivery condition Cold rolled narrow steel strip covered by EN 10132-4 shall be supplied in one of the following delivery conditions: annealed or annea

28、led and skin passed (+A or +LC); cold rolled (+CR); quenched and tempered (+QT). NOTE The delivery condition - annealed to achieve spheroidized carbides (+AC) - may be agreed. In such cases, limits on spheroidization and mechanical properties may also be agreed at the time of enquiry and order. 7.4

29、Chemical composition 7.4.1 Cast analysis The chemical composition shall be in accordance with the values specified in Table 1 for the cast analysis. 7.4.2 Product analysis In cases where a product analysis is requested, the admissible deviations from the values specified for the cast analysis are in

30、dicated in Table 2. 7.5 Mechanical properties 7.5.1 Tensile properties and hardness The mechanical properties of the strip shall be in accordance with the values given in Table 3. For thicknesses outside this range, mechanical properties shall be agreed between the customer and the supplier. NOTE 1

31、For those customers who specify Rockwell hardness rather than Vickers hardness or tensile strength, a table is given in A.1, showing Rockwell hardness values for information.Page 6 EN 10132-4:2000 BSI 05-2000 NOTE 2 The steels may be quenched in oil or isothermally heat treated. For information, the

32、 minimum hardness values given in Table A.2 show the minimum values after quenching, without tempering. NOTE 3 For spring applications, the preferred hardness range (HV) for steels according to Table 3 in the quenched and tempered condition are given in Table A.3 for information. 7.5.2 Bend test Req

33、uirements for the bend test for steels in the annealed condition (+A) may be agreed at the time of enquiry and order. 7.6 Structure 7.6.1 Grain size See EN 10132-1. 7.6.2 Non-metallic inclusions See EN 10132-1. 7.6.3 Decarburization For silicon alloyed steels, decarburization shall not exceed 3 % of

34、 the material thickness per side, for non-silicon alloyed steels, decarburization shall not exceed 2 % of the material thickness per side when measured at a distance of 5 mm from the strip edge (see also EN 10132-1). 7.7 Surface finish The surface finish of cold rolled narrow steel strip shall be br

35、ight as produced by rolling and annealing in a controlled atmosphere. The surface finishes of quenched and tempered cold rolled strip are as follows: grey/blue oxide finish: unpolished; brigth tempered: unpolished; polished: obtained by fine grinding, abrasive brushing or other processes; polished a

36、nd coloured: blue or yellow colour obtained by oxidization by heat treatment. 7.8 Dimensions and tolerances on dimensions and shape See EN 10132-1. 8 Inspection See EN 10132-1.Page 7 EN 10132-4:2000 BSI 05-2000 9 Sampling See EN 10132-1. 10 Test methods See EN 10132-1. 11 Labelling, packaging and pr

37、otection See EN 10132-1. 12 Retests See EN 10132-1.Page 8 EN 10132-4:2000 BSI 05-2000 Table 1 - Chemical composition of steels for springs and other special applications a(cast analysis) Steel designation % by mass name number C Si Mn P max. S max. Cr Mo max. V Ni C55S 1.1204 0,52 to 0,60 0,15 to 0,

38、35 0,60 to 0,90 0,025 0,025 max. 0,40 0,10 - max. 0,40 C60S 1.1211 0,57 to 0,65 0,15 to 0,35 0,60 to 0,90 0,025 0,025 max. 0,40 0,10 - max. 0,40 C67S 1.1231 0,65 to 0,73 0,15 to 0,35 0,60 to 0,90 0,025 0,025 max. 0,40 0,10 - max. 0,40 C75S 1.1248 0,70 to 0,80 0,15 to 0,35 0,60 to 0,90 0,025 0,025 ma

39、x. 0,40 0,10 - max. 0,40 C85S 1.1269 0,80 to 0,90 0,15 to 0,35 0,40 to 0,70 0,025 0,025 max. 0,40 0,10 - max. 0,40 C90S 1.1217 0,85 to 0,95 0,15 to 0,35 0,40 to 0,70 0,025 0,025 max. 0,40 0,10 - max. 0,40 C100S 1.1274 0,95 to 1,05 0,15 to 0,35 0,30 to 0,60 0,025 0,025 max. 0,40 0,10 - max. 0,40 C125

40、S 1.1224 1,20 to 1,30 0,15 to 0,35 0,30 to 0,60 0,025 0,025 max. 0,40 0,10 - max. 0,40 48Si7 1.5021 0,45 to 0,52 1,60 to 2,00 0,50 to 0,80 0,025 0,025 max. 0,40 0,10 - max. 0,40 56Si7 1.5026 0,52 to 0,60 1,60 to 2,00 0,60 to 0,90 0,025 0,025 max. 0,40 0,10 - max. 0,40 51CrV4 1.8159 0,47 to 0,55 max.

41、 0,40 0,70 to 1,10 0,025 0,025 0,90 to 1,20 0,10 0,10 to 0,25 max. 0,40 80CrV2 1.2235 0,75 to 0,85 0,15 to 0,35 0,30 to 0,50 0,025 0,025 0,40 to 0,60 0,10 0,15 to 0,25 max. 0,40 75Ni8 1.5634 0,72 to 0,78 0,15 to 0,35 0,30 to 0,50 0,025 0,025 0,15 0,10 - 1,80 to 2,10 125Cr2 1.2002 1,20 to 1,30 0.15 t

42、o 0,35 0,25 to 0,40 0,025 0,025 0,40 to 0,60 0,10 - max. 0,40 102Cr6 1.2067 0,95 to 1,10 0,15 to 0,35 0,20 to 0,40 0,025 0,025 1,35 to 1,60 0,10 - max. 0,40 a Elements not quoted in this table shall not be intentionally added to the steel without the agreement of the purchaser, other than for the pu

43、rpose of finishing the heat. All reasonable precautions shall be taken to prevent the addition, from scrap or other material used in manufacture, of such elements which affect the hardenability, mechanical properties and application.Page 9 EN 10132-4:2000 BSI 05-2000 Table 2 - Permissible deviations

44、 between the product analysis and the limiting values given in Table 1 for the cast analysis Element Permissible maximum content in the cast analysis % by mass Permissible deviation a % by mass C 0,50 0,50 1,00 1,00 1,30 0,02 0,03 0,04 Si 1,00 1,00 2,00 +0,03 0,10 Mn 1,00 1,00 1,10 0,04 0,05 P 0,025

45、 +0,005 S 0,025 +0,005 Cr 0,40 0,40 1,60 +0,03 0,04 Mo 0,10 +0,02 V 0,25 0,03 Ni 0,40 0,40 2,10 +0,03 0,05 a means that in one cast the deviation may occur over the upper value or under the lower value of the specified range in Table 1, but not both at the same time.Page 10 EN 10132-4:2000 BSI 05-20

46、00 Table 3 - Mechanical properties and hardness requirements a, b delivery condition Steel designation annealed (+A) or annealed and skin passed (+LC) cold rolled c(+CR) quenched and tempered (+QT) d name number R p0,2 e N/mm max. R m e N/mm max. A 80 e % min. HV e max. R m e N/mm max. HV e max. R m

47、 e N/mm HV e C55S 1.1204 480 600 17 185 1 070 300 1 100 to 1 700 340 to 520 C60S 1.1211 495 620 17 195 1 100 305 1 150 to 1 750 345 to 530 C67S 1.1231 510 640 16 200 1 140 315 1 200 to 1 900 370 to 580 C75S 1.1248 510 640 15 200 1 170 320 1 200 to 1 900 370 to 580 C85S 1.1269 535 670 15 210 1 190 32

48、5 1 200 to 2 000 370 to 600 C90S 1.1217 545 680 14 215 1 200 325 1 200 to 2 100 370 to 600 C100S 1.1274 550 690 13 220 1 200 325 1 200 to 2 100 370 to 630 C125S 1.1224 600 740 11 230 1 200 325 1 200 to 2 100 370 to 630 48Si7 1.5021 580 720 13 225 - - 1 200 to 1 700 370 to 520 56Si7 1.5026 600 740 12

49、 230 - - 1 200 to 1 700 370 to 520 51CrV4 1.8159 550 700 13 220 - - 1 200 to 1 800 370 to 550 80CrV2 1.2235 580 720 12 225 - - 1 200 to 1 800 370 to 550 75Ni8 1.5634 540 680 13 210 - - 1 200 to 1 800 370 to 550 125Cr2 1.2002 590 750 11 235 - - 1 300 to 2 100 405 to 630 102Cr6 1.2067 590 750 11 235 - - 1 300 to 2 100 405 to 630 a The customer may specify hardness or tensile values but not both. If neither is specified then tensile values shall apply. b Values apply to thicknesses 0,30 mm