BS EN 4007-2005 Aerospace series - Aluminium alloy AL-P6082-T6 or T62 - Sheet and strip - 0 4 mm a 6 mm《铝合金AL-P6082-T6或T62 薄板和带材 0 4 mm≤a≤6 mm》.pdf

《BS EN 4007-2005 Aerospace series - Aluminium alloy AL-P6082-T6 or T62 - Sheet and strip - 0 4 mm a 6 mm《铝合金AL-P6082-T6或T62 薄板和带材 0 4 mm≤a≤6 mm》.pdf》由会员分享，可在线阅读，更多相关《BS EN 4007-2005 Aerospace series - Aluminium alloy AL-P6082-T6 or T62 - Sheet and strip - 0 4 mm a 6 mm《铝合金AL-P6082-T6或T62 薄板和带材 0 4 mm≤a≤6 mm》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIESBS EN 4007:2005Aluminium alloy AL-P6082-T6 or T62 Sheet and strip 0,4 mm ka k6 mmICS 49.025.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g6

2、0g53g44g42g43g55g3g47g36g58IncorporatingcorrigendumNovember 2010 National forewordThis British Standard is the UK implementation of EN 4007:2005. It supersedes BS L 113:1971 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee ACE/61, Metallic materials for

3、 aerospace purposes, to Subcommittee ACE/61/-/24, Light alloys.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicati

4、on.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 4007:2005This British Standard waspublished under the authorityof the Standards Policy andStrategy Committeeon 4 October 2005 BSI 2010Amendments/corrigenda issued since publicationDate Comments 30 November 2010

5、 Addition of supersession details to national foreword.ISBN 978 0 580 72943 0EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4007 June 2005 ICS 49.025.20 English version Aerospace series - Aluminium alloy AL-P6082-T6 or T62 - Sheet and strip - 0,4 mm a 6 mm Srie arospatiale - Alliage daluminium

6、 AL-P6082-T6 ou T62 - Tles et bandes - 0,4 mm a 6 mm Luft- und Raumfahrt - Aluminiumlegierung AL-P6082-T6 oder T62 - Bleche und Bnder - 0,4 mm a 6 mm This European Standard was approved by CEN on 22 April 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

7、 the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists

8、 in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodie

9、s of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR

10、STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4007:2005: E2 Foreword This document (EN 4007

11、:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of th

12、e member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2005, and conflicting national standards shall be withdrawn at the latest by

13、 December 2005. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standa

14、rds organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slo

15、vakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 4007:2005EN 4007:2005 (E)3 Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This standard has been

16、prepared in accordance with EN 4500-2. 1 Scope This standard specifies the requirements relating to: Aluminium alloy AL-P6082- T6 or T62 Sheet and strip 0,4 mm a 6 mm for aerospace application. 2 Normative references The following referenced documents are indispensable for the application of this do

17、cument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 4258, Aerospace series Metallic materials General organization of standardization Links between types of EN standards and their u

18、se. EN 4400-2, Aerospace series Aluminium and aluminium alloy wrought products Technical specification Part 2: Sheet and strip. 1)EN 4500-2, Aerospace series Metallic materials Rules for drafting and presentation of material standards Part 2: Specific rules for aluminium, aluminium alloys and magnes

19、ium alloys. 1) 1) Published as AECMA Prestandard at the date of publication of this standard. BS EN 4007:2005EN 4007:2005 (E)4 1 Material designation Aluminium alloy AL-P6082- Others Element Si Fe Cu Mn Mg Cr Zn Ti Each Total Al min. 0,7 0,40 0,6 2 Chemical composition % max. 1,3 0,50 0,10 1,0 1,2 0

20、,25 0,20 0,10 0,05 0,15 Base 3 Method of melting 4.1 Form Sheet and strip 4.2 Method of production Rolled 4.3 Limit dimension(s) mm 0,4 a 6 5 Technical specification EN 4400-2 Delivery condition O H111 T4 T6 6.1 Heat treatment 525 C 540 C / WQ 40 C + = ambient / t 5 d 525 C 540 C / WQ 40 C + 160 C 1

21、80 C / 8 h t 16 h 6.2 Delivery condition code A F K U Use condition T62 T6 T67 Heat treatment Delivery condition + 525 C 540 C / WQ 40 C + 160 C 180 C / 8 h t 16 h Delivery condition + 160 C 180 C / 8 h t 16 h Delivery condition Characteristics 8.1 Test sample(s) See EN 4400-2. 8.2 Test piece(s) See

22、 EN 4400-2. 8.3 Heat treatment Delivery condition: O or H111 Use condition: T6 or T62 9 Dimensions concerned mm 0,4 a 3,0 3,0 a 6 0,4 a 0,8 0,8 a 6 10 Thickness of cladding on each face % 11 Direction of test piece LT LT LT LT 12 Temperature C Ambient Ambient Ambient Ambient13 Proof stress Rp0,2MPa

23、85 85 260 260 14 Strength RmMPa 150 150 310 310 15 Elongation A % A50mm 16 A50mm 18 A50mm 8 A50mm 9 16 T Reduction of area Z % 17 Hardness 18 Shear strength RcMPa 19 Bending k 1; = 180 1; = 180 20 Impact strength 21 Temperature C 22 Time h 23 Stress aMPa 24 Elongation a % 25 Rupture stress RMPa 26 C

24、 Elongation at rupture A % 27 Notes (see line 98) BS EN 4007:2005EN 4007:2005 (E)5 44 External defects See EN 4400-2. 82 Batch uniformity See EN 4400-2. 5 T4 T6 60 (Typical value) 100 (Typical value) 16 per product 20 per product 7 Hardness HB 24 per batch 30 per batch 95 Marking inspection See EN 4

25、400-2. 96 Dimensional inspection See EN 4400-2. 98 Notes 99 Typical use BS EN 4007:2005EN 4007:2005 (E)6 100 Product qualification See EN 4400-2. Qualification programme to be agreed between manufacturer and purchaser. BS EN 4007:2005EN 4007:2005 (E)blankBSI GroupHeadquarters 389 Chiswick High Road,

26、 London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standardsBSI - British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Roya

27、l Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inac

28、curacy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS whic

29、h ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using

30、a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of inform

31、ation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (

32、0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: I

33、nformation regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/ CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the interna

34、tional standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This d

35、oes not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager. Tel: +44 (0)20 8996 7070 Email: BS EN 4007:2005