BS EN 2591-420-2006 Aerospace series - Elements of electrical and optical connection - Test methods - Part 420 Mechanical strength of rear accessories《电气和光学连接元件 试验方法 后部附件的机械强度》.pdf

《BS EN 2591-420-2006 Aerospace series - Elements of electrical and optical connection - Test methods - Part 420 Mechanical strength of rear accessories《电气和光学连接元件 试验方法 后部附件的机械强度》.pdf》由会员分享，可在线阅读，更多相关《BS EN 2591-420-2006 Aerospace series - Elements of electrical and optical connection - Test methods - Part 420 Mechanical strength of rear accessories《电气和光学连接元件 试验方法 后部附件的机械强度》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58optical connection Test methods Part 420: Mechanical strength of rear accessoriesThe European Stand

2、ard EN 2591-420:2006 has the status of a British StandardICS 49.060Aerospace series Elements of electrical and BRITISH STANDARDBS EN 2591-420:2006BS EN 2591-420:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2006 BSI 2006ISBN

3、0 580 49435 7Amendments issued since publicationAmd. No. Date CommentsThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. National

4、forewordThis British Standard was published by BSI. It is the UK implementation of EN 2591-420:2006. It supersedes BS EN 2591-420:2001 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Su

5、bcommittee ACE/6/-/3, Aerospace Connectors.A list of organizations represented on ACE/6/-/3 can be obtained on request to its secretary.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2591-420July 2006ICS 49.060 Supersedes EN 2591-420:2001 English VersionAerospace series - Elements of electrical a

6、nd optical connection- Test methods - Part 420: Mechanical strength of rearaccessoriesSrie arospatiale - Organes de connexion lectrique etoptique - Mthodes dessais - Partie 420 : Tenuemcanique des accessoires arrireLuft- und Raumfahrt - Elektrische und optischeVerbindungselemente - Prfverfahren - Te

7、il 420:Mechanische Festigkeit der rckseitigen ZubehrteileThis European Standard was approved by CEN on 27 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any

8、 alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by tr

9、anslationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hu

10、ngary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre:

11、rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2591-420:2006: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Preparation of specimens.4 4 Apparatus .4 5 Method 4 6 Requiremen

12、ts.7 EN 2591-420:20063 Foreword This European Standard (EN 2591-420:2006) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received t

13、he approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2007, a

14、nd conflicting national standards shall be withdrawn at the latest by January 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Th

15、is document supersedes EN 2591-420:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hun

16、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2591-420:2006 4 1 Scope This standard specifies a method of determining the mechanical strength of rear acces

17、sories used on elements of electrical and optical connection subjected to bending, tensile and torsional forces. It shall be used together with EN 2591-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only th

18、e edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General. EN 2591-101, Aerospace series Elements of electrical and opti

19、cal connection Test methods Part 101: Visual examination. 3 Preparation of specimens Unless specified in the technical specification, the following details shall be stated: mounting and locking of specimens; for phase A, bending moment; for phase B, tensile force; for phase C, torsional moment; for

20、phase D, tightening torque; requirements. 4 Apparatus Equipment for applying and measuring the bending, tensile, torsional forces and torques. Fixture simulating the rear part of a connector. 5 Method The mounted specimens shall be subjected to the following test sequence unless otherwise stated. Du

21、mmy shells may be used. EN 2591-420:20065 a) Phase A: bending test With the specimens placed horizontally in the test fixture, bending moments shall be applied successively to the end of the accessory, see Figures 1, 2 and 3. The forces F1and F2and F3shall be increased at a rate not exceeding 20 N/s

22、 until the specified value is reached and maintained for 1 min. Figure 1 Bending moment (straight accessory) Figure 2 Bending moment (90 accessory) Figure 3 Bending moment (90 accessory) F3EN 2591-420:2006 6 b) Phase B: tensile test With the specimens placed horizontally in the test fixture, tensile

23、 force F shall be applied to the end of the accessory, see Figure 4 or Figure 5. It shall be increased at a rate not exceeding 20 N/s until the specified value is reached and maintained for 1 min. Figure 4 Tensile force (straight accessory) Figure 5 Tensile force (90 accessory) c) Phase C: torsion t

24、est With the specimens placed horizontally in the test fixture, the torsional moment C shall be applied to the end of the accessory, see Figure 6 or Figure 7. This torsional moment shall be increased at a rate not exceeding 0,1 Nm/s until the specified value is reached and maintained for one minute.

25、 Figure 6 Torsional moment (straight accessory) Figure 7 Torsional moment (90 accessory) EN 2591-420:20067 d) Phase D: torsion test on the mating thread With the specimens placed in the test fixture, a torque shall be applied to the coupling nut at a rate of 1 0,1 Nm/s until the specified value is r

26、eached and maintained for one minute. 6 Requirements At the end of phase D, prior to removal, there shall be no play between the accessory and the test fixture. The untightening torque shall comply with the specified value. After removal, the specimens shall be examined visually according to EN 2591

27、-101. No deformation shall be observed. EN 2591-420:2006 BS EN BSI389 Chiswick High RoadLondonW4 4AL2591-420:2006BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international

28、level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be g

29、rateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual

30、updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email:

31、 ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provide

32、s a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +4

33、4 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996

34、 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI

35、 also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying,

36、 recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.