BS EN 1929-4-2005 Basket trolleys - Requirements and tests for basket trolleys with additional goods carrying facility(ies) with or without a child carrying facility intended to be.pdf

《BS EN 1929-4-2005 Basket trolleys - Requirements and tests for basket trolleys with additional goods carrying facility(ies) with or without a child carrying facility intended to be.pdf》由会员分享，可在线阅读，更多相关《BS EN 1929-4-2005 Basket trolleys - Requirements and tests for basket trolleys with additional goods carrying facility(ies) with or without a child carrying facility intended to be.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58child carrying facility, intended to be used on passenger conveyorsThe European Standard EN 1929-4:

2、2005 has the status of a British StandardICS 97.130.30Basket trolleys Part 4: Requirements and tests for basket trolleys with additional goods carrying facility(ies), with or without a BRITISH STANDARDBS EN 1929-4:2005BS EN 1929-4:2005This British Standard was published under the authority of the St

3、andards Policy and Strategy Committee on 13 October 2005 BSI 13 October 2005ISBN 0 580 46557 8standard, BS EN 1929-1, 4.2.1.4 should be observed in this respect.Additional goods carrying facilities In its present form this standard permits the contents of some of the additional goods carrying facili

4、ties to be insecure and likely to fall onto the floor. Manufacturers and users of this standard should be aware that this could be hazardous to health and safety. Manufacturers should take steps to ensure that their designs hold contents securely. This could be achieved by ensuring that there are ap

5、propriate vertical sides of suitable height on the additional goods carrying facilities. Designs ought to ensure that no goods could be kicked out by a child sitting in the child seat.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesTh

6、e British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standar

7、ds Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an

8、inside front cover, the EN title page, pages 2 to 9 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsLeg room The UK committee would like to draw the users attention to BS EN 1929

9、-1, 4.2.1.4, which specifies adequate space for the trolley users stride. In this UK interests informed; monitor related international and European developments and promulgate them in the UK.National forewordThis British Standard is the official English language version of EN 1929-4:2005.The UK part

10、icipation in its preparation was entrusted to Technical Committee CW/51, Shopping trolleys, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep EUROPE

11、AN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1929-4April 2005ICS 97.130.30English versionBasket trolleys - Part 4: Requirements and tests for baskettrolleys with additional goods carrying facility(ies), with or withouta child carrying facility, intended to be used on passengerconveyorsChariots dachat

12、 corbeille - Partie 4 : Prescriptions etessais pour les chariots dachat corbeille et dispositif(s)supplmentaire(s) de dpose de marchandises, avec ousans sige pour enfant, destins tre utiliss sur trottoirsroulantsEinkaufswagen - Teil 4: Anforderungen und Prfungen frEinkaufswagen mit zustzlichen Abste

13、lleinrichtungen frWaren, mit oder ohne Kindersitz, geeignet fr denGebrauch auf PersonenfahrsteigenThis European Standard was approved by CEN on 14 February 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard t

14、he status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German)

15、. A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark,

16、Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KO

17、MITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1929-4:2005: EEN 1929-4:2005 (E) 2 Contents Page Foreword3 1 Scope 5 2 Normative references 5 3 Terms and def

18、initions .5 4 Safety 5 5 Inspections and tests 6 6 Signboards, use instructions and marking.6 7 Tests7 Bibliography 9 EN 1929-4:2005 (E) 3 Foreword This document (EN 1929-4:2005) has been prepared by Technical Committee CEN/TC 291 “Self service shopping trolleys”, the secretariat of which is held by

19、 BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2005, and conflicting national standards shall be withdrawn at the latest by October 2005. According to the CEN/CENELEC Internal Regul

20、ations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, No

21、rway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 1929-4:2005 (E) 4 Introduction This document is a part of a series of standards currently under preparation by CEN/TC 291. The parts of this series are: EN 1929-1 Basket trolleys Part 1: Requirements and te

22、sts for basket trolleys with or without a child carrying facility EN 1929-2 Basket trolleys Part 2: Requirements, tests and inspection for basket trolleys with or without a child carrying facility, intended to be used on passenger conveyors EN 1929-3 Basket trolleys Part 3: Requirements and tests fo

23、r basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility EN 1929-4 Basket trolleys Part 4: Requirements and tests for basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility, intended to be used on passe

24、nger conveyors prEN 1929-6: Basket trolleys Part 6: Requirements, tests and inspection for basket trolleys with base trays for Do It Yourself markets intended to be used on passenger conveyors EN 1929-7: Basket trolleys Part 7: Requirements and tests for basket trolleys with baby and child carrying

25、facilities EN 1929-4:2005 (E) 5 1 Scope This document specifies requirements for the construction, performance, testing and safety specifications for general purpose self-service basket trolleys, with additional goods carrying facility(ies), with or without a child carrying facility, intended to be

26、used on passenger conveyors, accompanied by a user. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

27、 any amendments) applies. EN 115, Safety rules for the construction and installation of escalators and passenger conveyors EN 1929-1:1998, Basket trolleys Part 1: Requirements and tests for basket trolleys with or without a child carrying facility EN 1929-2:2004, Basket trolleys Part 2: Requirements

28、, tests and inspection for basket trolleys with or without a child carrying facility, intended to be used on passenger conveyors EN 1929-3:2005, Basket trolleys Part 3: Requirements and tests for basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility

29、3 Terms and definitions For the purposes of this document the terms and definitions given in EN 1929-2:2004 and EN 1929-3:2005 and the following apply. 3.1 basket trolley with goods carrying facility(ies) intended to be used on passenger conveyors manually driven trolley with goods carrying facility

30、(ies), suitable for use on a passenger conveyor 4 Safety 4.1 Generalities Trolleys covered by this document are intended to be used on passenger conveyors conforming with EN 115 and shall comply with EN 1929-3, with the exception of subclause 4.1 only for the diameter of the wheels (in Table 1 parag

31、raph line 4.2.2 rolling quality of EN 1929-1:1998, where the diameter of the wheels shall be not less than 120 mm), subclause 5.5, Clause 6. 4.2 Total loading mass When used on a passenger conveyor, the total loading mass of the trolley shall not exceed 160 kg. 4.3 Space between the trolley and pass

32、enger conveyor The difference between the overall width of the trolley and the nominal width of the passenger conveyor shall be not less than 400 mm. EN 1929-4:2005 (E) 6 4.4 Maintaining the trolley on the passenger conveyor The trolley shall be equipped with a device that maintains it in a stopped

33、position in the absence of any outside intervention. The diameter of the wheels shall not be less than 120 mm. 4.5 Stability The trolley shall not overturn, when tested in accordance with: 7.1.2, up to and including 16 in the ascending and descending direction; 7.1.3, up to and including 10 in the s

34、ideways direction. 4.6 Stability when exiting the passenger conveyor The trolley shall not overturn in the descending direction when encountering the comb at the exit of the passenger conveyor. This requirement is considered to be met when the trolley conforms to test 7.3. 5 Inspections and tests Se

35、e 5 of EN 1929-2:2004. 6 Signboards, use instructions and marking 6.1 Signboards and use instructions See 6.1 of EN 1929-2:2004. 6.2 Marking Trolleys shall have a pictogram conforming to Figure 2 in paragraph 6.1 of EN 1929-2:2004 of dimensions not less than 20 mm x 20 mm and permanently affixed to

36、the handle. The maximum basket load shall be clearly visible to the user. An identification plate including the following indications shall be visibly and permanently affixed to each trolley: manufacturers name or trade mark; address of the manufacturer; commercial name of the trolley and indicated

37、volume (in accordance with 4.4 of EN 1929-1:1998); calculated volume in litres (in accordance with 3.10 of EN 1929-1:1998); maximum load in kilograms (in accordance with 3.11 of EN 1929-1:1998 and 4.2 of this document); load of every goods carrying facility in kilograms (see 3.7 of EN 1929-3:2005);

38、month and year of manufacture; number and date of this document. The maximum load of the child carrying facility for type D trolley, i.e. 15 kg (see 4.9 of EN 1929-1:1998) shall be clearly displayed on the trolley. EN 1929-4:2005 (E) 7 7 Tests 7.1 Stability tests 7.1.1 General Stability tests shall

39、be carried out with the additional load(s) simulating the goods carrying facility(ies) (see 4.2.4.2 of EN 1929-3:2005), as described in Table 1: on type C trolleys with the basket empty, on type D trolleys with the basket empty and with a load simulating a child in the child carrying facility as des

40、cribed in 5.4 of EN 1929-1:1998. Table 1 Loading of goods carrying facility(ies) for the stability tests Goods carrying facility Lateral stability Longitudinal stability forward Longitudinal stability backward Below the basket (see Figure 1, position a in 3.1 of EN 1929-3:2005) Empty Empty Empty Beh

41、ind the basket (see Figure 1, position b in 3.1 of EN 1929-3:2005) Empty Empty Loaded as described in 4.2.4.2 of EN 1929-3:2005 In connection with the back rest (see Figure 1, position c in 3.1 of EN 1929-3:2005) Loaded as described in 4.2.4.2 of EN 1929-3:2005 Empty Loaded as described in 4.2.4.2 o

42、f EN 1929-3:2005 At the front of the basket (see Figure 1, position d in 3.1 of EN 1929-3:2005) Loaded as described in 4.2.4.2 of EN 1929-3:2005 Loaded as described in 4.2.4.2 of EN 1929-3:2005 Empty Above the bottom of the basket (see Figure 1, position e in 3.1 of EN 1929-3:2005) Loaded as describ

43、ed in 4.2.4.2 of EN 1929-3:2005 Loaded as described in 4.2.4.2 of EN 1929-3:2005 Empty EN 1929-4:2005 (E) 8 7.1.2 Longitudinal stability test The test device shall consist of a tilting platform equipped with a 20 mm high strip placed parallel to the axis of inclination and acting as a limit stop for

44、 the trolley wheels. The test shall be carried out at room temperature. Place the swivelling castors in the least stable position. Tilt the trolley on the test apparatus, in the ascending and descending direction to an angle of 16. If the trolley does not overturn at an angle up to and including 16,

45、 then it shall be deemed to conform to this document. 7.1.3 Lateral stability test The test device shall consist of a tilting platform equipped with a 20 mm high strip placed parallel to the axis of inclination and acting as a limit stop for the trolley wheels. The test shall be carried out at room

46、temperature. Place the swivelling castors in the least stable position. Tilt the trolley on the test apparatus, to either side, to an angle of 10. If the trolley does not overturn at an angle up to and including 10, then it shall be deemed to conform to this document. 7.2 Test for maintaining trolle

47、ys on passenger conveyors See 7.2 of EN 1929-2:2004. 7.3 Toppling test when exiting from the passenger conveyor For trolleys with goods carrying facility at the front of the basket (see Figure 1, position d in 3.1 of EN 1929-3:2005), load only the goods carrying facility as described in 4.2.4.2 of E

48、N 1929-3:2005. For trolleys without goods carrying facility at the front of the basket (see Figure 1, positions a, b, c, e in 3.1 of EN 1929-3:2005), place only a 400 mm x 300 mm x 300 mm cuboid with a homogenous mass of 24 kg in the basket of the trolley, in the most unfavourable position, i.e. the

49、 centre of gravity being as near as possible to the front face of the trolley. The test apparatus shall consist of a tilting platform equipped with a 20 mm high strip placed parallel to the axis of inclination and acting as a limit stop for the trolley wheels. The test shall be carried out at room temperature. Place the trolley on the test platform with the swivelling castors directed towards the rear of the trolley. Tilt the trolley facing i