BS EN 1734-1997 Rubber- or plastics- coated fabrics - Determination of resistance to water penetration - Low-pressure method《橡胶或塑料涂覆织物 耐水渗透性测定 低压法》.pdf

《BS EN 1734-1997 Rubber- or plastics- coated fabrics - Determination of resistance to water penetration - Low-pressure method《橡胶或塑料涂覆织物 耐水渗透性测定 低压法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1734-1997 Rubber- or plastics- coated fabrics - Determination of resistance to water penetration - Low-pressure method《橡胶或塑料涂覆织物 耐水渗透性测定 低压法》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1734 : 1997 The Eur

2、opean Standard EN 1734 : 1996 has the status of a British Standard ICS 59.080.40 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Rubber- or plastics- coated fabrics Determination of resistance to water penetration Low-pressure methodBS EN 1734 : 1997 This British Standard, hav

3、ing been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 May 1997 BSI 1997 The following BSI references relate to the work on this standard: Committee reference TCI/78 Draft for comment

4、 95/121356 DC ISBN 0 580 27192 7 Amendments issued since publication Amd. No. Date Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee TCI/78, Coated fabrics, upon which the following bodies were represented: Br

5、itish Plastics Federation British Rubber Manufacturers Association Ltd. British Textile Technology Group Furniture Industry Research Association Home Office Made-up Textiles Association Ministry of Defence RAPRA Technology Ltd. SATRA Footwear Technology Centre Society of British Aerospace Companies

6、Ltd. Society of Motor Manufacturers and Traders Limited The Textile InstituteBS EN 1734 : 1997 BSI 1997 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Method 1 Scope 3 2 Normative references 3 3 Principle 3 4 Apparatus 3 5 Test specimens 3 6 Procedure 4 7 E

7、xpression of results 4 8 Test report 4ii BSI 1997 BS EN 1734 : 1997 National foreword This British Standard has been prepared by Technical Committee TCI/78, and is the English language version of EN 1734 : 1996 Rubber- or plastics-coated fabrics Determination of resistance to water penetration Low-p

8、ressure method, published by the European Committee for Standardization (CEN). No current British Standard is superseded. Cross-references Publication referred to Corresponding British Standard EN ISO 2231 : 1995 BS EN ISO 2231 : 1995 Testing coated fabrics Part 2. Method 4. Pre-conditioning and con

9、ditioning of coated fabrics for testing purposes EN 22286 : 1993 BS EN 22286 : 1994 Methods for the determination of length and width of a roll, net mass and mean mass per unit area of a piece, cut, roll or sample and the determination of thickness for coated fabrics Additional information Attention

10、 is drawn to the fact that other means of assessing the hydrostatic resistance properties of coated fabrics are given in BS 3424 : Part 26 : 1990 and ISO 1420 : 1987. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprise

11、s a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4 , an inside back cover and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 199

12、6 Copyright reserved to CEN members Ref. No. EN 1734 : 1996 E EUROPEAN STANDARD EN 1734 NORME EUROPE ENNE EUROPA ISCHE NORM November 1996 ICS 59.080.40 Descriptors: coated fabrics, fabrics coated with rubber, fabrics coated with plastics, watertightness, fluid-tightness tests, pressure tests, hydros

13、tatic tests English version Rubber- or plastics-coated fabrics Determination of resistance to water penetration Low-pressure method Supports textiles reve tus de caoutchouc ou de plastique De termination de la re sistance a l a pe ne tration de leau Me thode a basse pression Mit Gumi- oder kunststof

14、fbeschichtete Textilien Bestimmung der Wasserdichtheit Verfahren bei geringem Druck This European Standard was approved by CEN on 1996-09-28. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nat

15、ional standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in a

16、ny other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ice

17、land, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 1734 : 1996 BSI 1997 Foreword This European Standard has been prepared by Technical Committee CEN/TC 248, Textiles and textile products, the secretariat of which is held by BSI. T

18、his European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1997, and conflicting national standards shall be withdrawn at the latest by May 1997. According to the CEN/CENELEC Internal Regulations, the nat

19、ional standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Page 3 EN 1734 :

20、1996 BSI 1997 1 Scope This standard specifies a method for the determination of the resistance of rubber- or plastics-coated fabrics to water penetration (hydrostatic resistance) when subjected to a specific hydrostatic pressure over a fixed period of time. Two test specimen sizes are given; one is

21、circular, the other square. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subseq

22、uent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN ISO 2231 Rubber- or plastics-coated fabrics Standard atmospheres fo

23、r conditioning and testing (ISO 2231 : 1989) EN 22286 Rubber- or plastics-coated fabrics Determination of roll characteristics (ISO 2286 : 1986) 3 Principle A test specimen of coated fabric is subjected to an increasing pressure of water on one face, under standard conditions, until a predetermined

24、pressure specified in the coated fabric specification is obtained. The required pressure is maintained for a specified time or until penetration occurs, whichever is the sooner. 4 Apparatus 4.1 General The apparatus consists of a well, fitted with a clamp to fasten the test specimen over the well. T

25、he well has a nozzle on its lower part, allowing it to be connected to a water inlet pipe so as to fill it at room temperature. A restraining mesh is fitted over the test specimen. This mesh comprises wires of 1 mm up to 1,2 mm diameter to form squares of not greater than 30 mm side. 4.2 Means of me

26、asuring water pressure Either a manometer connected to the testing head, allowing water pressure up to 19,6 kPa (200 cmH 2 O) to be read to an accuracy of 1%, or a pressure gauge, graduated in centimetres head of water, or in kilopascals with a maximum reading of at least 100 kPa (946 cmH 2 O), is u

27、sed as the means of measuring the water pressure applied to the test specimen. 4.3 Test specimen area The open part of the well (4.1) over which the test specimen is clamped shall be either a square having a side of 100 mm (100 cm 2 ) or a circle of 113 mm diameter (100 cm 2 ). If necessary, soft ru

28、bber sealing gaskets can be employed between the coated fabric test specimen and the surfaces of the clamps in order to reduce the risk of damage to the test specimen by the clamps, and to facilitate the testing of seams. In this respect, rubber having a hardness of approximately 40 IRHD (Internatio

29、nal Rubber Hardness Degree) and approximately 1 cm thick or 1 cm in diameter has been found useful. Alternatively, a closed-cell, cross-linked polyethylene foam having a density of 45 kg/m 3 to 55 kg/m 3 and approximately 1 cm thick has also been used. 5 Test specimens 5.1 Conditioning Immediately p

30、rior to testing, condition the test specimens for at least 16 h in an appropriate atmosphere in accordance with EN ISO 2231. 5.2 Sampling Test specimens shall be taken from an area with no functional or visible defects and shall be located in the usable width of the coated fabric as defined in EN 22

31、286. 5.3 Number of test specimens Unless otherwise specified in the material specification, five test specimens shall be tested for each series of tests. 5.4 Shape and dimensions 5.4.1 Square Each test specimen shall be a square with sides measuring approximately 200 mm. 5.4.2 Circular Each test spe

32、cimen shall have a diameter of 130 mm to 200 mm.Page 4 EN 1734 : 1996 BSI 1997 6 Procedure 6.1 Test method With the vessel connected to the water inlet pipe, open the inlet valve and allow the water to run until it overflows. Check that the vessel is horizontal by ensuring that the water is uniforml

33、y flush with all four edges. The open part of the well may be circular. Ensure that the inlet pipe is totally purged of air, and also that the level of water in the vessel corresponds to the zero on the manometer tube. Place the test specimen on the vessel with the face to be tested, moistened prior

34、 to the test, in contact with the water, without trapping any air under the test specimen. Fit the retaining mesh (see 4.1). Secure the test specimen and the mesh firmly on the vessel using the clamp, taking care to ensure that the edges of the clamp are completely parallel with those of the vessel.

35、 6.2 Application of pressure Open the inlet valve so that the pressure gradually increases in the vessel at an approximate rate of 1 m per 3 min. The pressure shall be verified using either a manometer or a pressure gauge (see 4.2). Once the required pressure has been reached, control the inlet valv

36、e, if necessary, and maintain the pressure for the required time (3 min to 5 min). Then inspect the visible part of the test specimen in order to detect whether any water droplets have passed through the coated fabric. Close the vessel inlet valve and return the pressure to zero by opening the evacu

37、ation valve. If a leak is detected in the test specimen clamping zone during the test, begin again. 7 Expression of results The visible face of the coated fabric shall not have any water penetration points nor any trace of moisture, on any of the five test specimens. A water penetration point is con

38、sidered to be any spot in which a drop appears as a pin prick and grows to reach a diameter of 1 mm to 1,5 mm. Penetration occurring exactly on the edges of the clamp shall not be considered to be a water penetration point. 8 Test report The test report shall include the following: a) the date of th

39、e test; b) reference to this standard; c) the description of the coated fabric; d) the conditioning and testing atmosphere used; e) the number of test specimens used; f) whether the test specimens were square or circular; g) which side(s) of the coated fabric were subjected to water pressure; h) the

40、 pressure level and the time applied; i) whether any leakage occurred and at what time interval; j) if applicable, the specific conditions used for ageing or other testing; k) details of any deviations from the standard test procedure. BSI 1997 BS EN 1734 : 1997 List of references See national forew

41、ord.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | B

42、SI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Use

43、rs of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secret

44、ary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buyin

45、g standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as

46、 British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which gi

47、ve details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefit

48、s contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Ac

49、t 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the