BS EN 1337-8-2007 Structural bearings nPart 8 Guide Bearings and Restraint nBearings《结构轴承 第8部分 导向轴承和止推轴承》.pdf

《BS EN 1337-8-2007 Structural bearings nPart 8 Guide Bearings and Restraint nBearings《结构轴承 第8部分 导向轴承和止推轴承》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1337-8-2007 Structural bearings nPart 8 Guide Bearings and Restraint nBearings《结构轴承 第8部分 导向轴承和止推轴承》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN1337-8:2007ICS 91.010.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDStructural bearingsPart 8: Guide Bearings and RestraintBearingsLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56, Uncontrolled Copy, (c) BSIThis British Standard w

2、as published under the authority of the Standards Policy and Strategy Committee on 30 September 2009 BSI 2009ISBN 978 0 580 55858 0Amendments/corrigenda issued since publicationDate CommentsBS EN 1337-8:2007National forewordThis British Standard is the UK implementation of EN 1337-8:2007. Together w

3、ith the other published parts of the BS EN 1337 series, it supersedes BS 5400-9.1:1983 and BS 5400-9.2:1983 which are withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/522, Structural bearings.A list of organizations represented on this committee can be obtained

4、 onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS

5、, 15/12/2009 00:56, Uncontrolled Copy, (c) BSIBS EN 1337-8:2007EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1337-8October 2007ICS 91.010.30English VersionStructural bearings - Part 8: Guide Bearings and RestraintBearingsAppareils dappui structuraux - Partie 8 : Appareils dappuiguids et appareil

6、s dappui bloqusLager im Bauwesen - Teil 8: Fhrungslager undFesthaltekonstruktionenThis European Standard was approved by CEN on 23 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a nat

7、ional standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in a

8、ny other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Esto

9、nia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCH

10、ES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1337-8:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56, Uncontrolled Copy

11、, (c) BSIBS EN 1337-8:2007EN 1337-8:2007 (E) 2 Contents Page Foreword4 1 Scope 5 2 Normative references 5 3 Terms, Definitions, Symbols and Abbreviations6 3.1 Terms and definitions .6 3.2 Symbols and Abbreviations .8 4 Functional Requirements8 4.1 General8 4.2 Durability 9 5 Material Properties.9 5.

12、1 General9 5.2 Ferrous materials.9 5.3 Structural Fasteners9 5.4 Welding .9 5.5 Anchors 9 6 Design Rules 9 6.1 General9 6.2 Rotational Elements 10 6.3 Minimum plate thickness 10 6.4 Connection to Packing and Anchor Plates .10 6.5 Clearances11 6.6 Combination with other bearings and/or elements11 7 M

13、anufacturing tolerances and corrosion protection .11 7.1 General11 7.2 Corrosion protection .11 8 Conformity evaluation.11 8.1 General11 8.2 Control of the construction product and its manufacture 11 8.2.1 Initial type testing 11 8.2.2 Factory production control.12 8.3 Raw materials and constituents

14、.12 8.4 Sampling.12 Annex A (normative) Factory production control (FPC) .13 A.1 General13 A.1.1 Objects13 A.1.2 Documentation.13 A.1.3 Operations 13 A.2 Verifications and tests 14 A.2.1 General comments.14 A.2.2 Monitoring of conformity 14 A.2.3 Tests14 A.2.4 Treatment of construction products whic

15、h do not conform.14 A.2.5 Recording of verifications and tests (manufacturers register)15 A.3 Traceability.15 Annex B (informative) Examples of Combined Bearings16 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56, Uncontrolled Copy, (c) BSIBS EN 1337-8:2007EN 1337-8:2007 (E) 3

16、 Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Products Directive .18 ZA.1 Scope and relevant characteristic .18 ZA.2 Procedures for attestation of conformity of Guide and Restraint Bearings .19 ZA.2.1 Systems of attestation of conformity19 ZA.

17、2.2 Certificate and Declaration of conformity.20 ZA.3 CE marking and labelling22 ZA.3.1 General .22 ZA.3.2 Declaration of product properties .23 ZA.3.3 Declaration of compliance with given design specification .23 Bibliography26 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56

18、, Uncontrolled Copy, (c) BSIBS EN 1337-8:2007EN 1337-8:2007 (E) 4 Foreword This document (EN 1337-8:2007) has been prepared by Technical Committee CEN/TC 167 “Structural bearings”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, eithe

19、r by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by July 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CEN

20、ELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with EC Directiv

21、e(s), see informative Annex ZA, which is an integral part of this document. This document was prepared by Working Group 1 and Working Group 3 of CEN TC 167 “Structural Bearings“. This European Standard EN 1337 consists of the following 11 parts: Part 1 General design rules Part 2 Sliding elements Pa

22、rt 3 Elastomeric bearings Part 4 Roller bearings Part 5 Pot bearings Part 6 Rocker bearings Part 7 Spherical and cylindrical PTFE bearings Part 8 Guide bearings and Restraint bearings Part 9 Protection Part 10 Inspection and maintenance Part 11 Transport, storage and installation According to the CE

23、N/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

24、Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56, Uncontrolled Copy, (c) BSIBS EN 1337-8:2007EN 1337-8:2007 (E) 5 1 Scope This Part of this

25、 European Standard deals with the requirements for the design and manufacture of Guide Bearings and Restraint Bearings. Guide Bearings and Restraint Bearings are not intended to transmit vertical loads but they may be combined in one unit with bearings in accordance. EN 1337-1:2000, Table 1. NOTE 1

26、Guide Bearings and Restraint Bearings are shown in EN 1337-1:2000, Table 1, No. 8.1 and 8.2. For combined bearings see EN 1337-1:2000, Table 1, bearing Nos. 1.2, 1.3, 1.6, 1.7, 1.8., 3.1, 4.1, 4.2, 4.3, 7.1, 7.3, and 7.4 with restraints and Nos. 1.5, 1.7, 2.2, 3.3, 3.4, 5.2, 6.2 and 7.3 with guides.

27、 NOTE 2 Examples of combined bearings are given in Annex B. The minimum operating temperature depends on the materials properties used at the required temperature and the limitations given in the referenced parts of this European Standard. NOTE 3 In certain circumstances the bearings described in th

28、is part of this European Standard may be required to operate in a plane inclined to the horizontal. In such circumstances the terms “vertical“ and “horizontal“ should be interpreted appropriately. 2 Normative references The following referenced documents are indispensable for the application of this

29、 document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1337-1:2000, Structural bearings Part 1: General design rules EN 1337-2:2004, Structural bearings Part 2: Sliding elements EN

30、1337-5:2005, Structural bearings Part 5: Pot bearings EN 1337-9, Structural bearings Part 9: Protection EN 1990, Eurocode Basis of structural design EN 10025, Hot rolled products of structural steels EN 10204, Metallic products Types of inspection documents EN 10083-3, Steels for quenching and tempe

31、ring - Part 3: Technical delivery conditions for alloy steels EN 10088-2, Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10340, Steel castings for structural uses prEN 1090-2, Execution of steel structures and

32、aluminium structures - Part 2: Technical requirements for the execution of steel structures ISO 898, Mechanical properties of fasteners made of carbon steel and alloy steel (all parts) ISO 1083, Spheroidal graphite cast irons Classification ISO 3755, Cast carbon steels for general engineering purpos

33、es Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56, Uncontrolled Copy, (c) BSIBS EN 1337-8:2007EN 1337-8:2007 (E) 6 ISO 4587, Adhesives - Determination of tensile lap-shear strength or rigid-to-rigid bonded assemblies 3 Terms, Definitions, Symbols and Abbreviations 3.1 Terms

34、and definitions For the purpose of this European Standard the following terms and definitions apply. 3.1.1 anchor plate optional plate that is positioned between the bearing plate and the main structure, normally permanently attached to the latter; provided to allow easy replacement of the bearing 3

35、.1.2 bearing plate plate that is an integral part of the bearing and forms the main support to which restraints and guides are attached 3.1.3 packing plate optional plate placed between the bearing plate and the anchor plate for adjusting the overall height of the bearing 3.1.4 sliding element combi

36、nation of appropriate materials with flat or curved surfaces in accordance with EN 1337-2 3.1.5 rotational element element that transmits the specified forces and permits rotations about at least one axis 3.1.6 guide bearing bearing that provides restraint in one horizontal direction only, accommoda

37、tes rotations and does not transmit vertical loads (see EN 1337-1:2000, Table 1, No. 8.2). Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56, Uncontrolled Copy, (c) BSIBS EN 1337-8:2007EN 1337-8:2007 (E) 7 Key 1 indicates sliding elements 2 indicates rotation elemet Figure 1 Ex

38、amples of guide bearings 3.1.7 restraint bearing bearing that prevents movements in the horizontal plane, accommodates rotations and does not transmit vertical loads (see EN 1337-1:2000, Table 1, No. 8.1) Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56, Uncontrolled Copy, (c)

39、 BSIBS EN 1337-8:2007EN 1337-8:2007 (E) 8 Figure 2 Examples for restraint bearings 3.2 Symbols and Abbreviations ais the minor side of an anchor plate or a bearing plate, or is the smallest dimension of PTFE (see 6.5 and 7.1). mm bis the major side of an anchor plate or a bearing plate . mm CM Compo

40、site Material PTFE Polytetrafluoroethylene 4 Functional Requirements 4.1 General Guide bearings and restraint bearings shall be designed to: transmit horizontal forces; allow vertical movements; allow movements in one or no horizontal directions; allow rotations; generate low resistance to movement;

41、 have durability appropriate to their intended use. NOTE As a consequence of the above these devices do not transmit applied vertical loads and bending moments. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56, Uncontrolled Copy, (c) BSIBS EN 1337-8:2007EN 1337-8:2007 (E) 9 4.

42、2 Durability To achieve durability with respect to repeated loading, low and high temperature, corrosion and ozone or chemical substances all requirements of this standard shall be met. 5 Material Properties 5.1 General The materials shall be selected for their compatibility within the expected temp

43、erature range of the structure. 5.2 Ferrous materials Guide Bearings and Restraint Bearings shall be manufactured from steels in accordance with one of the following standards: EN 10025, EN 10083-3, EN 10088-2, EN 10340, ISO 3755 and ISO 1083. 5.3 Structural Fasteners Data in specifications and cert

44、ification of material shall correspond to the requirements relating to stress. All materials used shall comply with ISO 898. 5.4 Welding Welding materials shall comply with prEN 1090-2. 5.5 Anchors Steel for shear studs shall have a guaranteed yield stress of not less than 340 N/mm2. Dowels and shea

45、r bars shall meet the requirements of sub-clause 5.2 and shall be fixed by welding or by bolts. 6 Design Rules 6.1 General The design values of the effects (forces, deformations, movements) from the actions at the supports of the structure shall be calculated from the relevant combination of actions

46、 according to EN 1990 and sections from 2 to 6 inclusive of both Parts 1 and 2 of EN 1991. NOTE 1 Until rules for the combination of actions for bearings become available in EN 1990, the guidance given in EN 1993-2 should be used. The various elements of guide bearings and restraint bearings shall b

47、e designed in accordance with the relevant Eurocodes or the other relevant parts of this European Standard. NOTE 2 For the design of steel parts see EN 1993. NOTE 3 For composite material see also EN 13372:2004, sub-clause 6.3. For the design of rotational elements Parts 3, 5 (6.2.3 and 6.2.4), 6 an

48、d 7 of this European Standard shall be applied, as appropriate. Guides shall be designed in accordance with EN 1337-2. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 15/12/2009 00:56, Uncontrolled Copy, (c) BSIBS EN 1337-8:2007EN 1337-8:2007 (E) 10 NOTE 4 It is recommended that the design va

49、lues of effects be provided in a bearing schedule as shown in EN 1993-2. The movement capacity shall be verified by geometrical analysis under the fundamental combination of actions. The horizontal movement capacity shall be increased by the values given in EN 1337-1:2000, sub-clause 5.4. The vertical design movement capacity shall be at least the following: 15 mm upwards; 10 mm downwards. For the design of the combined units (see 1 Scope) the Part of this European Standard relevant to the device