BS EN 1192-2000 Doors - Classification of strength requirements《门 强度要求的分类》.pdf

《BS EN 1192-2000 Doors - Classification of strength requirements《门 强度要求的分类》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1192-2000 Doors - Classification of strength requirements《门 强度要求的分类》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1192:2000 Incorpora

2、ting Corrigendum No. 1 The European Standard EN 1192:1999 has the status of a British Standard ICS 91.060.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Doors Classification of strength requirementsThis British Standard, having been prepared under the direction of the Sect

3、or Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 May 2000 BSI 08-2000 ISBN 0 580 34782 6 BS EN 1192:2000 Amendments issued since publication Amd. No. Date Comments 11033 Corrigendum No. 1 August 2000 Indicated b

4、y a sideline | | National foreword This British Standard is the official English language version of EN 1192:1999. The UK participation in its preparation was entrusted by Technical Committee B/538, Doors, windows, shutters, hardware and curtain walling, to Subcommittee B/538/2, Doors, which has the

5、 responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. This Britis

6、h Standard forms part of a package of standards on doors which will not become fully effective until all standards in the package have been published and any superseded standards have been withdrawn. The date of withdrawal for national standards will be agreed within CEN and this will be notified in

7、 Update Standards. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the se

8、ction entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicatio

9、n. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the doc

10、ument was last issued. Sidelining in this document indicates the most recent changes by amendment.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1192 November 1999 ICS 91.060.50 English version Doors - Classification of strength requirements Portes Classification des exigences de rsistance mca

11、nique Tren - Klassifizierung der Festigkeitsanforderungen This European Standard was approved by CEN on 20 September 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard with

12、out any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language m

13、ade by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Icelan

14、d, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels 1999 CEN All rights of exploitati

15、on in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1192:1999 EPage 2 EN 1192:1999 BSI 08-2000 Foreword This European Standard has been prepared by Technical Committee CEN/TC 33, Doors, windows, shutters and building hardware, the Secretariat of which is held by

16、AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2000, and conflicting national standards shall be withdrawn at the latest by May 2000. According to the CEN/CENELEC Internal Regulations,

17、 the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United K

18、ingdom. This standard is one of a series of standards for doors. The performance levels relate to test methods published in EN 947, EN 948, EN 949 and EN 950. This standard presents a partial, provisional and interim classification for doors, restricted to the aspect of mechanical strength in resist

19、ing vertical load, static torsion, soft and heavy body impact, and hard body impact. It is intended to establish a standard for a complete classification scheme which includes all relevant properties valid for different families of doors. The standard includes an informative Annex A which, gives gen

20、eral guidance on the relationship between performance levels and categories of duty. 1 Scope This standard provides a means of classifying where appropriate, the performance of door leaves, door frames, door sets, and door assemblies according to their strength in resisting vertical load, static tor

21、sion, soft and heavy body impact, and hard body impact. The performance levels indicate normal usage for a range of categories of duty. Special requirements such as those for burglar resistance or safety requirements related to glass infillings are not covered. 2 Normative references This European S

22、tandard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply

23、 to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 947 Hinged or pivoted doors - Determination of the resistance to vertical load. EN 949 Windows and curtain walling, doors, blinds and

24、 shutters - Determination of the resistance to soft and heavy body impact for doors. EN 948 Hinged or pivoted doors - Determination of the resistance to static torsion. EN 950 Door leaves - Determination of the resistance to hard body impact. 3 Definitions For the purposes of this standard the follo

25、wing definitions apply: 3.1 door assembly a complete assembly as installed, comprising door frame and one or more leaves, together with its essential hardware supplied from separate sources.Page 3 EN 1192:1999 BSI 08-2000 3.2 door set a complete unit consisting of a door frame and a door leaf or lea

26、ves, supplied with the essential hardware and weatherseal, as a product from a single source. 4 Requirements Imposed stresses and accidental impacts on doors shall neither damage them nor impair their performance. 4.1 General The attributes are identified in clauses 4.2, 4.3, 4.4 and 4.5. After test

27、ing against attributes 4.2, 4.3 and 4.4 the test specimen shall continue to function normally. Application of the tests shall not result in the specimen suffering such damage or deformation, including loosening of hardware or joints, which render it unfit for its purpose, nor shall any of its compos

28、ite parts become dislodged or shattered. Small fissures in timber in the vicinity of the lock, latch or keep are permitted provided the hardware is neither loosened nor dislodged and the door maintains its functionality. 4.2 Resistance to vertical load Hinged or pivoted doors shall be tested in acco

29、rdance with EN 947. This specifies the method to be used to determine the permanent deformation caused when a vertical load is applied to the free edge of an open door leaf fixed in its own frame. The load to be applied shall be selected from the performance levels given in Table 1. For a door to qu

30、alify for a particular performance class, the resultant residual deformation measured in accordance with EN 947 shall not exceed 1 mm. 4.3 Resistance to static torsion Hinged or pivoted doors shall be tested in accordance with EN 948. This specifies the method to be used to determine the permanent d

31、eformation caused when static stress in torsion is applied to an open door leaf fixed in its own frame. The load to be applied shall be selected from the performance classes given in Table 1. For a door to qualify for a particular performance class, the resultant residual deformation measured in acc

32、ordance with EN 948 shall not exceed 2 mm. 4.4 Resistance to soft and heavy body impact Hinged, pivoted or sliding doors shall be tested in accordance with EN 949. This specifies the method to be used to determine the damage caused by striking with a soft and heavy body, the face of a closed door le

33、af fixed in its own frame. The impact energy to be applied shall be selected from the performance levels given in Table 1. It shall be applied three times to each face of the door leaf. For a door to qualify for a particular performance class, the resultant residual deformation in flatness measured

34、in accordance with EN 949 shall not exceed 2 mm. 4.5 Resistance to hard body impact Door leaves shall be tested in accordance with EN 950. This specifies the method to be used to determine the damage caused to a door leaf by the impact of a hard object. The test shall be used to determine the struct

35、ural integrity of the construction and not the effect of such impacts upon appearance.Page 4 EN 1192:1999 BSI 08-2000 The impact energy to be applied shall be selected from the performance levels given in Table 1. For a door to qualify for a particular performance class, the mean value of the diamet

36、ers of indentations shall not exceed 20 mm and the mean value of the depths of indentations caused shall not exceed 1,0 mm, and the maximum value shall not exceed 1,5 mm. 5 Classification of mechanical strength Four classes are defined in the classification system shown in Table 1. Hinged or pivoted

37、 doors shall be subjected in turn to Tests 1, 2, 3 and 4. Sliding doors shall be subjected to Tests 3 and 4 only. To qualify for an overall performance class, the requirements of all relevant tests shall be satisfied at that level. Alternatively, it is permitted to indicate performance by reference

38、to the individual class achieved for each test. Table 1: Classification and load/energy values to be applied Test Resistance to: Class 1 Class 2 Class 3 Class 4 1 Vertical load, N 400 600 800 1 000 2 Static torsion, N 200 250 300 350 3 Soft and heavy body impact, J 30 60 120 180 4 Hard body impact,

39、J 1,5 3 5 8Page 5 EN 1192:1999 BSI 08-2000 Annex A (informative) Information for users Doors are employed in a range of situations in buildings varying from an interior door in a dwelling which is used rarely, or an external door of a dwelling leading onto gravel and then generally with care, to an

40、entrance door of a shop which is in constant use by people who have little incentive to exercise care and who may be carrying bulky objects or propelling trolleys. This is a wide spectrum of use, but for all practical purposes, this range can be covered by the four performance classes given in this

41、standard. Generally, it is desirable to state the specific use and requirements of the product. However where this is not possible, the general guidance given in Table A1 can be used to assist in the selection of appropriate classes. Table A1 (informative): Classes and categories of duty Class Categ

42、ory of duty Description 1 - 2 Light to medium duty Low frequency of use with care, for example by private house owners where there is a small chance of accident occurring or of misuse. 2 - 3 Medium to heavy duty Medium frequency of use primarily with care, where there is some chance of accident occu

43、rring or of misuse. 3 - 4 Heavy to severe duty High frequency of use without care, where there is a good chance of accident occurring or of misuse. 4 Severe duty Subject to frequent violent usage.BS EN 1192:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | |

44、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for prepar

45、ing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions

46、. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside

47、 front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be a

48、ddressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide

49、 range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fa