BS EN 1154-1997 Building hardware - Controlled door closing devices - Requirements and test methods《建筑五金 控制门关闭装置 要求和试验方法》.pdf

《BS EN 1154-1997 Building hardware - Controlled door closing devices - Requirements and test methods《建筑五金 控制门关闭装置 要求和试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1154-1997 Building hardware - Controlled door closing devices - Requirements and test methods《建筑五金 控制门关闭装置 要求和试验方法》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 1154:1997Incorporating Amendment No. 1 and Building hardware Controlled door closing devices Requirements and test methodsThe European Standard EN 1154:1996, with the incorporation of amendment A1:2002, has the status of a British StandardICS 91.190g49g50g3g38g50g51g60g44g49g42

2、g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Corrigenda No. 1 andNo. 2BS EN 1154:1997This British Standard, having been prepared under the direction of the Board for Building

3、 and Civil Engineering Sector Board, was published under the authority of the Standards Board on 15 July 1997 BSI 2006ISBN 0 580 27476 4Committees responsible for this British StandardThe preparation of this British Standard was entrusted by Technical Committee B/538, Doors, windows, shutters, hardw

4、are and curtain walling, to Subcommittee B/538/4, Building hardware, upon which the following bodies were represented:Association of Builders Hardware ManufacturersAssociation of Building Component ManufacturersAssociation of Building EngineersBritish Plastics FederationBritish Security Industry Ass

5、ociationBritish Woodworking FederationConsumer Policy Committee of BSICouncil for Aluminium in BuildingDepartment of the Environment (Building Research Establishment)Glass and Glazing FederationGuild of Architectural IronmongersInstitute of Architectural IronmongersLHC Building Components and Servic

6、esLoss Prevention CouncilNational House-building CouncilAmendments issued since publicationAmd. No. Date Comments14074 20 February 2003 See revised national foreword14399 Corrigendum No. 113 March 2003 National foreword corrected16312 September 2006 Correction to classification box in 4.8 andCorrige

7、ndum No. 2 paragraph 3 of ZA.3BS EN 1154:1997 BSI 13 March 2003iContentsPageCommittees responsible Inside front coverNational foreword iiForeword 2Text of EN 1154 3BS EN 1154:1997ii BSI 13 March 2003National forewordThis British Standard is the official English language version of EN 1154:1996,inclu

8、ding amendment A1:2002 and Corrigendum February 2006 published bythe European Committee for Standardization (CEN).The start and finish of text introduced or altered by CEN amendment A1 is indicated in the text by tags g33g34.The UK participation in its preparation was entrusted by Technical Committe

9、e B/538, Doors, windows, shutters, hardware and curtain walling, to its Subcommittee B/538/4, Building hardware, which has the responsibility to:EN 1154:1996 (as amended) is a candidate “harmonized” European Standard and fully takes into account the requirement of the European Commission mandate M10

10、1, Doors, windows, shutters, gates and related hardware, given under the EU Construction Products Directive (89/106/EEC), and intended to lead to CE marking. The date of applicability of EN 1154:1996 (as amended) as a “harmonized” European Standard, i.e. the date after which this standard may be use

11、d for CE marking purposes, is subject to an announcement in the Official Journal of the European Communities.The Commission in consultation with Member States have agreed a transition period for the co-existence of “harmonized” European Standards and their corresponding national standard(s). It is i

12、ntended that this period will comprise a period, usually nine months after the date of availability of the European Standard, during which any required changes to national regulations are to be made, followed by a further period, usually twelve months, for the implementation of CE marking. At the en

13、d of this co-existence period, the national standard(s) will be withdrawn.Since BS EN 1154:1997 is the current national standard the changes introduced by amendment no. 1 may be implemented from nine months after publication.Based on this transition period of twenty-one months BS EN 1154:1997 (as am

14、ended) will be fully effective in September 2004.NOTE This date is approximate. Users of this standard should contact BSI Customer Services for confirmation.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which i

15、mplement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication

16、does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee

17、any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pag

18、es 2 to 27 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1154November 1996+ A1December 2002February 2006ICS 91.060.50; 97.180Descriptors: Hardware, buildings, doors, hinged doors, doo

19、r closing devices, stopping devices, shock absorbers, definitions,classifications, specifications, performance evaluation, installation, tests, fatigue tests, performance tests, corrosion resistance,markingEnglish versionBuilding hardware Controlled door closing devices Requirements and test methods

20、(includes amendment A1:2002)Quincaillerie pour le btiment Dispositifs de fermeture de porte avec amortissement Prescriptions et mthodes dessai(inclut lamendment A1:2002)Schlsser und Baubeschlge Trschliemittelmit kontrolliertem Schlieablauf Anforderungen und Prfverfahren(enthlt nderung A1:2002)This E

21、uropean Standard was approved by CEN on 1996-09-28 and amendmentA1 was approved by CEN on 2002-11-07. CEN members are bound to complywith the CEN/CENELEC Internal Regulations which stipulate the conditionsfor giving this European Standard the status of a national standard without anyalteration.Up-to

22、-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to anyCEN member.This European Standard exists in three official versions (English, French,German). A version in any other language made by translation under ther

23、esponsibility of a CEN member into its own language and notified to theCentral Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Denmark,Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,Netherlands, Norway

24、, Portugal, Spain, Sweden, Switzerland and UnitedKingdom.CENEuropean Committee for StandardizationComit Europen de NormalisationEuropisches Komitee fr NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members.Ref. No. EN 1154:1996 + A1:2002 EEN 1154:1996

25、BSI 13 March 20032ForewordThis European Standard has been prepared by Technical Committee CEN/TC 33, Doors, windows, shutters, building hardware and curtain walling, the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publicati

26、on of an identical text or by endorsement, at the latest by May 1997, and conflicting national standards shall be withdrawn at the latest by May 1997.This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essentia

27、l requirements of EU Directive 89/106/EEC.For relationship with EU Directive 89/106/EEC, see informative Annex ZA, which is an integral part of this document.Wherever reference is made to classes, they are considered to be technical classes and not classes according to Article 3(2) of the Constructi

28、on Products Directive (89/106/EEC).This European Standard is part of a package of European Standards dedicated to building hardware products, and derives from performance requirements contained in various texts cited in Annex E.According to the CEN/CENELEC Internal Regulations, the national standard

29、s organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Foreword to amendment A1This do

30、cument EN 1154:1996/A1:2002, has been prepared by Technical Committee CEN/TC 33, Doors, windows, shutters, building hardware and curtain walling, the Secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical t

31、ext or by endorsement, at the latest by June 2003, and conflicting national standards shall be withdrawn at the latest by September 2004.This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirement

32、s of EU Directive(s).For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.NOTE This amendment refers only to requirements under the Construction Products Directive (89/106/EEC), and CE marking is considered only in regard to this Directive. Wher

33、e full CE marking may require compliance with other directives it is understood that this is done by following the relevant risk assessment(s) of these other directives, performed in addition to the requirements of this standardAccording to the CEN/CENELEC Internal Regulations, the national standard

34、s organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.ContentsForeword 21Scope 32 Nor

35、mative references 33 Definitions 34 Classification 55 Requirements 76 Test apparatus 87 Test methods 108 Marking 149 Evaluation of conformity 15Annex A (normative) Additional requirements for door closing devices intended for use on fire/smoke door assemblies 16Annex B (normative) Flow chart of test

36、 procedure 17Annex C (informative) Door closer and door types 18Annex D (informative) Overload performance test apparatus 21Annex E (informative) Bibliography 23Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive (89/106/EEC) 2

37、4EN 1154:1996 BSI 13 March 200331 ScopeThis standard specifies requirements for controlled door closing devices for swing doors, such devices being mounted on or in the frame, on or in the door, or in the floor.The scope is limited to manually operated door closing devices where the energy for closi

38、ng is generated by the user upon opening the door, such that when the door is released, it returns to a closed position, in a controlled manner.Devices such as spring hinges, which do not exert a checking control during door closing, are outside the scope of this standard.Door closing devices (door

39、closers) manufactured in accordance with this standard are recommended for use wherever there is a requirement for reliable closing control of a door.Door closers for use on fire/smoke doors need additional attributes in order to contribute actively to meeting the essential safety requirements in ca

40、se of fire, either independently or as part of a complete door assembly.These additional requirements for door closers for use on a fire/smoke door assembly are specified in normative Annex A.Door closers incorporating electrically powered hold-open mechanisms, for use on fire/smoke door assemblies,

41、 are covered by g33EN 1155.g34g33Door closers incorporating door coordinator devices (with or without electrically powered hold-open devices) are covered by EN 1158.g342 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These n

42、ormative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated r

43、eferences the latest edition of the publication referred to applies.g33EN 1155g34, Building hardware Electrically powered hold-open devices for swing doors Requirements and test methods.g33EN 1670:1998g34, Building hardware Corrosion resistance of hardware for doors, windows, shutters and curtain wa

44、lling Requirements and test methods.g33EN 1634-1, Fire resistance tests for door and shutter assemblies Part 1: Fire doors and shutters.g34g33EN 1634-3, Fire resistance tests for door and shutter assemblies Part 3: Smoke control doors and shutters.g343 DefinitionsFor the purposes of this standard, t

45、he following definitions apply:3.1controlled door closing device (door closer)any manually operated door closing mechanism where the energy for closing is generated by the user upon opening the door, and when released, returns the door to the closed position, in a controlled manner. The term include

46、s all arms, brackets, shoes, top centres, floor pivots and other parts supplied with the device and necessary for its installation and operation3.2overhead door closer surface mounteda door closer mounted at or near the door head, on the surface of the door or its transom (g33see Figure C.1.1g34)3.3

47、overhead concealed door closer door mounteda door closer, mounted within the thickness of the door (g33g115g115see Figure C.1.2g34)EN 1154:19964 BSI 13 March 20033.4overhead concealed door closer transom mounteda door closer mounted within the thickness of the transom (g33see Figure C.1.3g34)3.5floo

48、r concealed door closer floor springa door closer mounted within the floor (g33see Figure C.1.4g34)3.6double action door closera door closer which allows operation of a door in both directions (g33see Figure C.2.1g34)3.7single action door closera door closer for use on doors which can open in one di

49、rection only and which close against a fixed stop (g33see Figure C.2.2g34)3.8door widththe width of the door leaf including any rebated door edges (g33see Figure C.2.3g34)3.9closing momentg33the torque generatedg34 by the door closing device which acts upon the door leaf during the closing operation3.10opening momentg33the torque generatedg34g32 by the user which acts upon the door leaf during the opening operation3.11backcheckan inbuilt buffer which helps to prevent a door leaf being flung wide open3.12delayed cl