BS DD IEC PAS 62611-2009 Vacuum cleaners for commercial use - Methods for measuring performance《商用真空吸尘器 测量性能法》.pdf

《BS DD IEC PAS 62611-2009 Vacuum cleaners for commercial use - Methods for measuring performance《商用真空吸尘器 测量性能法》.pdf》由会员分享，可在线阅读，更多相关《BS DD IEC PAS 62611-2009 Vacuum cleaners for commercial use - Methods for measuring performance《商用真空吸尘器 测量性能法》.pdf（70页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI British StandardsWB9423_BSI_StandardColCov_noK_AW:BSI FRONT COVERS 5/9/08 12:55 Page 1Vacuum cleaners for commercialuse Methods for measuring performanceDD IEC/PAS 62611:2009National forewordThis Dra

2、ft for Development is the UK implementation of IEC/PAS 62611:2009.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publications and is ofa provisional nature. It should be applied on this provisional basis, so thatinformation and

3、experience of its practical application can be obtained.A PAS is a Technical Specification not fulfilling the requirements for a stan-dard, but made available to the public and established in an organizationoperating under a given procedure.A review of this Draft for Development will be carried out

4、not later than threeyears after its publication.Notification of the start of the review period, with a request for the submis-sion of comments from users of this Draft for Development, will be made inan announcement in the appropriate issue of Update Standards. Accordingto the replies received, the

5、responsible BSI Committee will judge whether thevalidity of the PAS should be extended for a further three years or what otheraction should be taken and pass their comments on to the relevant interna-tional committee.Observations which it is felt should receive attention before the official callfor

6、comments will be welcomed. These should be sent to the Secretary of theresponsible BSI Technical Committee at British Standards House, 389 ChiswickHigh Road, London W4 4AL.The UK participation in its preparation was entrusted by Technical CommitteeCPL/59, Performance of household electrical applianc

7、es, to SubcommitteeCPL/59/6, Floor treatment appliances.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2009

8、ISBN 978 0 580 65710 8ICS 97.080Compliance with a British Standard cannot confer immunity fromlegal obligations.This Draft for Development was published under the authority of theStandards Policy and Strategy Committee on 31 October 2009Amendments issued since publicationAmd. No. Date Text affectedB

9、RITISH STANDARDDD IEC/PAS 62611:2009IEC/PAS 62611Edition 1.0 2009-07PUBLICLY AVAILABLE SPECIFICATIONPRE-STANDARD Vacuum cleaners for commercial use Methods for measuring performance INTERNATIONAL ELECTROTECHNICAL COMMISSION XBICS 97.080 PRICE CODEISBN 2-8318-1042-2 Registered trademark of the Intern

10、ational Electrotechnical Commission DD IEC/PAS 62611:2009 2 PAS 62611 IEC:2009(E) CONTENTS FOREWORD.6 INTRODUCTION.8 1 Scope.9 2 Normative references .9 3 Terms and definitions .9 4 General conditions for testing.11 4.1 Atmospheric conditions .11 4.2 Test equipment and materials.12 4.3 Voltage and f

11、requency 12 4.4 Running-in of vacuum cleaner and attachments .12 4.5 Equipment of the vacuum cleaner12 4.6 Operation of the vacuum cleaner.13 4.7 Conditioning prior to tests13 4.8 Initial application of dust13 4.9 Mechanical operator13 4.10 Number of samples .13 4.11 In-house reference cleaner syste

12、m(s)13 5 Dry vacuum cleaning tests14 5.1 Dust removal from hard flat floors14 5.1.1 Test equipment14 5.1.2 Test area and stroke length .14 5.1.3 Removal of remaining dust 14 5.1.4 Distribution of test dust14 5.1.5 Preconditioning of dust receptacle.14 5.1.6 Determination of dust removal ability.15 5

13、.2 Dust removal from hard floors with uneven surfaces15 5.2.1 Test equipment15 5.2.2 Distribution of test dust15 5.2.3 Determination of dust removal ability.15 5.3 Dust removal from carpets.16 5.3.1 Test carpet 16 5.3.2 Test area and stroke length .16 5.3.3 Conditioning of test carpet.17 5.3.4 Distr

14、ibution of test dust17 5.3.5 Embedding of dust into carpet .17 5.3.6 Preconditioning of dust receptacle.17 5.3.7 Determination of dust removal ability.18 5.4 Dust removal along walls.19 5.4.1 Test equipment and materials19 5.4.2 Distribution of test dust19 5.4.3 Determination of dust removal ability

15、 along walls.19 5.5 Fibre removal from carpets20 5.6 Maximum usable volume of the dust receptacle.20 5.6.1 Conditions for measurement20 DD IEC/PAS 62611:2009PAS 62611 IEC:2009(E) 3 5.6.2 Introduction of moulding granules20 5.6.3 Determination of maximum usable volume of dust receptacle 20 5.7 Air da

16、ta .20 5.7.1 Conditions for measurement21 5.7.2 Test equipment21 5.7.3 Determination of air data .21 5.8 Performance with loaded dust receptacle 22 5.8.1 Determination of suction pressure change with loaded dust receptacle .22 5.8.2 Throttling to simulate loaded dust receptacle.25 5.8.3 Determinatio

17、n of performance with loaded dust receptacle 26 5.9 Filtration efficiency of the vacuum cleaner.26 5.9.1 Test conditions 26 5.9.2 Determining the test dust quantity .26 5.9.3 Test procedure 26 5.9.4 Evaluation .27 5.9.5 Particle concentration and dilution.29 5.9.6 Record keeping .29 5.10 HEPA filtra

18、tion equivalence of the vacuum cleaner30 5.10.1 Object of the test .30 5.10.2 Test procedure 30 5.10.3 Determination of HEPA equivalence 30 5.11 Total emissions of the vacuum cleaner30 5.11.1 Test method 30 6 Miscellaneous tests 30 6.1 Motion resistance 31 6.1.1 Test carpet and test equipment .31 6.

19、1.2 Determination of motion resistance31 6.2 Cleaning under office furniture 31 6.2.1 Distribution of test dust32 6.2.2 Determination of free office furniture height .32 6.3 Maximum radius of operation.32 6.3.1 Conditions for measurement32 6.3.2 Determination of radius of operation 32 6.4 Impact res

20、istance 32 6.4.1 Test equipment33 6.4.2 Determination of impact resistance33 6.5 Deformation of hose and connecting tubes 33 6.5.1 Test equipment33 6.5.2 Determination of permanent deformation .33 6.6 Bump test34 6.6.1 Test equipment34 6.6.2 Test cycle35 6.6.3 Test procedure 36 6.7 Flexibility of th

21、e hose 36 6.7.1 Preparation of test object.36 6.7.2 Determination of the flexibility of the hose .37 6.8 Repeated bending of the hose.37 DD IEC/PAS 62611:2009 4 PAS 62611 IEC:2009(E) 6.8.1 Test equipment37 6.8.2 Test method 38 6.9 Life test .38 6.10 Mass .39 6.11 Weight in hand 39 6.12 Dimensions .3

22、9 6.13 Noise level 39 6.14 Energy consumption39 6.14.1 Energy consumption when vacuuming of carpets.39 6.14.2 Energy consumption with vacuuming of hard floors with uneven surfaces 41 7 Test material and equipment 42 7.1 Material for measurements 42 7.1.1 Test carpets 42 7.1.2 Standard dust type 43 7

23、.1.3 Fibre material 45 7.1.4 Moulding granules .45 7.2 Equipment for measurements 45 7.2.1 Floor test plate 45 7.2.2 Test plates with uneven surfaces.45 7.2.3 Carpet-beating machine 45 7.2.4 Carpet hold-downs and guides 46 7.2.5 Dust spreader47 7.2.6 Rollers for embedding .47 7.2.7 Equipment for air

24、 data measurement .48 7.2.8 Test equipment for determining the fractional filtration efficiency of the vacuum cleaner .52 7.2.9 Device for motion resistance test.54 7.2.10 Device for impact test54 7.2.11 Device for determination of deformation of hoses and connecting tubes .55 7.2.12 Mechanical oper

25、ator 56 7.2.13 Weighing machine .57 8 Instructions for use.57 9 Information at the point of sale .58 Annex A (informative) Information on materials59 Annex B (informative) Information at the point of sale 62 Annex C (informative) Information on materials63 Bibliography65 Figure 1 Right-angled T .19

26、Figure 2 Air data curves.22 Figure 3a Connecting tube openings23 Figure 4 Test dust for loading dust receptacle24 Figure 5 Dust spread uniformly on surface .25 Figure 6 Insertion depth.32 Figure 7 Position of test object and cross-section for measurement of deformation34 DD IEC/PAS 62611:2009PAS 626

27、11 IEC:2009(E) 5 Figure 8a Profile of threshold.35 Figure 8b Arrangements for bump test .35 Figure 9 Preparation of hoses for testing flexibility.37 Figure 10 Equipment for repeated bending of hoses 38 Figure 11 Grain size diagram for test dust44 Figure 12 Carpet-beating machine .46 Figure 13 Carpet

28、 hold-downs and guides .46 Figure 14 Dust spreader and roller for embedding dust into carpets.47 Figure 15a Alternative A equipment for air data measurements48 Figure 15b Measuring box for alternative A49 Figure 15c Alternative B equipment for air data measurements50 Figure 15 Alternative A and B 50

29、 Figure 16 Drum for impact test.55 Figure 17 Device for testing deformation of hoses and connecting tubes56 Figure 18 Mechanical operator for the measurement of dust removal from carpets and of motion resistance.57 Table 1 Confidence limits of a Poisson distribution for 95 % confidence range29 DD IE

30、C/PAS 62611:2009 6 PAS 62611 IEC:2009(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ VACUUM CLEANERS FOR COMMERCIAL USE METHODS FOR MEASURING PERFORMANCE FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotec

31、hnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specification

32、s, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, g

33、overnmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisio

34、ns or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for internat

35、ional use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order

36、 to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clear

37、ly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall

38、 attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal

39、 fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publi

40、cation. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. A PAS is a technical specification not fulfilling the requirements for a standard,

41、but made available to the public. IEC-PAS 62611 has been processed by subcommittee 59F: Floor treatment appliances, of IEC technical committee 59: Performance of household and similar electrical appliances. The text of this PAS is based on the following document: This PAS was approved for publicatio

42、n by the P-members of the committee concerned as indicated in the following document Draft PAS Report on voting 59F/184/PAS 59F/185/RVDFollowing publication of this PAS, which is a pre-standard publication, the technical committee or subcommittee concerned may transform it into an International Stan

43、dard. This PAS is based on the 4th edition of IEC 60312 (Vacuum cleaners for household use Method of measuring the performance), and has been adapted to the operating environment of commercial appliances. DD IEC/PAS 62611:2009PAS 62611 IEC:2009(E) 7 This PAS shall remain valid for an initial maximum

44、 period of 3 years starting from the publication date. The validity may be extended for a single 3-year period, following which it shall be revised to become another type of normative document, or shall be withdrawn. DD IEC/PAS 62611:2009 8 PAS 62611 IEC:2009(E) INTRODUCTION This PAS specifies provi

45、sional methods of measuring the performance of commercial vacuum cleaners for use in offices, shops and similar commercial establishments taking into account the differences in operation compared to household vacuum cleaners. It is the intention of subcommittee SC 59F to review this PAS based on exp

46、erience achieved and publish an International Standard on this subject. DD IEC/PAS 62611:2009PAS 62611 IEC:2009(E) 9 VACUUM CLEANERS FOR COMMERCIAL USE METHODS FOR MEASURING PERFORMANCE 1 Scope These test methods are applicable to vacuum cleaners for commercial use. The purpose of this PAS is to spe

47、cify essential performance characteristics of vacuum cleaners being of interest to the users and to describe methods for measuring these characteristics. NOTE Due to the influence of environmental conditions, variations in time, origin of test materials and proficiency of the operator, most of the d

48、escribed test methods will give more reliable results when applied for comparative testing of a number of appliances at the same time, in the same laboratory and by the same operator. For safety requirements, refer to IEC 60335-1, IEC 60335-2-2 and IEC 60335-2-69. 2 Normative references The followin

49、g referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60312, Vacuum cleaners for household use Methods of measuring the performance IEC 60704-1, Household and similar electrical appliances Test code for the determination of airborne acoustical noise Part 1: General re