BS DD IEC PAS 60704-2-15-2009 Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Particular requirements for household foo.pdf

《BS DD IEC PAS 60704-2-15-2009 Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Particular requirements for household foo.pdf》由会员分享，可在线阅读，更多相关《BS DD IEC PAS 60704-2-15-2009 Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Particular requirements for household foo.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationHousehold and similar electricalappliances Test code for thedetermination of airborneacoustical noise Part 2-15: Particular requirements for householdfood waste disposersDD IEC/P

2、AS 60704-2-15:2DD IEC/PAS 60704-2-15:2008Incorporating corrigendum July 2012This publication is not to be regarded as a British Standard.t is being issued in the Draft for Development series of publications and isof a provisional nature. It should be applied on this provisional basis, sothat informa

3、tion and experience of its practical application can beobtained.A PAS is a Technical Specification not fulfilling the requirements for astandard, but made available to the public and established in an organi-zation operating under a given procedure.A review of this Draft for Development will be carr

4、ied out not later thanthree years after its publication.Notification of the start of the review period, with a request for the sub-mission of comments from users of this Draft for Development, will be made in anannouncement in the appropriate issue of Update Standards.According to the replies receiv

5、ed, the responsible BSI Committee willjudge whether the validity of the PAS should be extended for a furtherthree years or what other action should be taken and pass their com-ments on to the relevant international committee.Observations which it is felt should receive attention before the official

6、of a contract. Users are responsible for its correct application. BSI 200ISBN 978 0 580 64257 9ICS 17.140.20; 97.040.50Amendments issued since publication Amd. No. Date Text affectedBRITISH STANDARDDD IEC/PAS 60704-2-15:20089This Published Document was published under the authority of theStandards P

7、olicy and Strategy Committee on February 2009.National foreword BSI 200ISBN 978 0 580 64257 9ICS 17.140.20; 97.040.50Amendments issued since publicationAmd. No. Date Text affectedDRAFT FOR DEVELOPMENTDD IEC/PAS 60704-2-15:2008The UK participation in its preparation was entrusted to TechnicalCommitte

8、e CPL/59, Performance of household electrical appliances.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.The Brit

9、ish Standards Institution 2012.Published by BSI Standards Limited 2012I 8 0 0 80315 4Amendments/corrigenda issued since publicationDate Text affected2012: Figure 101 replacedImplementation of IEC corrigendum July 30 September 2012Compliance with a British Standard cannot confer immunity from legal o

10、bligations.28This Draft for Development is the UK implementation of IEC/PAS 60704-2-15:2008 incorporating corrigendum July 2012.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publications and is of a provisional nature. It shoul

11、d be applied on this provisional basis, so that information and experience of its practical application can be obtained.A PAS is a Technical Specification not fulfilling the requirements for a standard, but made available to the public and established in an organization operating under a given proce

12、dure.A review of this Draft for Development will be carried out not later than three years after its publication.Notification of the start of the review period, with a request for the submission of comments from users of this Draft for Development,will be made in anannouncement in the appropriate is

13、sue of Update Standards. According to the replies received, the responsible BSICommittee will judge whether the validity of the PAS should be extended for a further three years or what other action should be taken and pass their comments on to the relevant international committee.Observations which

14、it is felt should receive attention before the official call for comments will be welcomed. These should be sent to the Secretary of the responsible BSI Technical Committee at British Standards House, 389 Chiswick High Road, London W4 4AL.IEC/PAS 60704-2-15Edition 1.0 2008-08PUBLICLY AVAILABLE SPECI

15、FICATIONPRE-STANDARD Household and similar electrical appliances Test code for the determination of airborne acoustical noise Part 2-15: Particular requirements for household food waste disposers INTERNATIONAL ELECTROTECHNICAL COMMISSION MICS 97.040.50 PRICE CODEISBN 2-8318-9914-1 Registered tradema

16、rk of the International Electrotechnical Commission 2 PAS 60704-2-15 IEC:2008(E)CONTENTSINTRODUCTION. 5 1 Scope. .62 Normative references .73 Terms and definitions. 74 Measurement methods and acoustical environment75 Instrumentation 86 Operation and location of appliances under test 87 Measurement o

17、f sound pressure levels108 Calculation of sound pressure and sound power levels. 109 Information to be recorded.10 10 Information to be reported .11Figure 101 Test enclosure 12DD IEC/PAS 60704-2-15:2008PAS 60704-2-15 IEC:2008(E) 5 INTRODUCTION The measuring conditions specified in this proposed test

18、 code provide for sufficient accuracy in determining the noise emitted, and comparing the results taken by different laboratories, whilst simulating as far as possible the practical use of food waste disposers.It is recommended to consider the determination of noise levels as part of a comprehensive

19、 testing procedure covering many aspects of properties and performance of food waste disposers.NOTE As stated in the introduction to IEC 60704-1, this test code is concerned with airborne noise only.DD IEC/PAS 60704-2-15:2008 6 PAS 60704-2-15 IEC:2008(E)HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES TE

20、ST CODE FOR THE DETERMINATION OF AIRBORNE ACOUSTICAL NOISE Part 2-15: Particular requirements for household food waste disposers 1 Scope This clause of Part 1 is applicable except as follows:1.1 Scope 1.1.1 General Replacement These particular requirements apply to single unit electric food waste di

21、sposers for householdand similar use, with or without automatic program control, for cold water supply, forpermanent connection to water supply and sewage systems, intended for connection to thekitchen sink drain and contained within a kitchen cabinet enclosure.Limitations for the use of this test c

22、ode are given in 1.1.1 of IEC 60704-1.1.1.2 Types of noise Replacement ISO 3743-1, ISO 3743-2, and ISO 3744 may be used for measuring noise emitted by foodwaste disposers.1.1.3 Size of the source Replacement The method specified in ISO 3744 is applicable to noise sources of any size. When applyingIS

23、O 3743-1 and ISO 3743-2, care should be taken that the maximum size of the cabinetenclosing the food waste disposer under test fulfills the requirements specified in 1.3 ofISO 3743-1 and ISO 3743-2.1.2 ObjectAddition Requirements for the declaration of noise emission values are not within the scope

24、of thisstandard. NOTE For determining and verifying noise emission values declared in product specifications, see IEC 60704-3.1.3 Measurement uncertaintyAddition Standard deviations for the kitchen machine category of appliances from IEC 60704-3 areapplicable.DD IEC/PAS 60704-2-15:2008PAS 60704-2-15

25、 IEC:2008(E) 7 2 Normative referencesThis clause of Part 1 is applicable. Addition: ANSI/ASME A112.19.3-2000, Stainless Steel Plumbing Fixtures (Designed for ResidentialUse)3 Terms and definitionsThis clause of Part 1 is applicable except as follows:3.4 operational cycleAddition: This begins with th

26、e start of the cycle by the operator and ends either when the operator turnsoff the disposer for manual operation or the disposer is turned off by a controller for automaticoperation Addition:3.101 batch feed operation method of operation in which the operator loads the food waste into the container

27、 body priorto starting the water flow and then the operational cycle of the disposer3.102 standard hard test load for noise measurements the standard “hard” test load for noise measurements during grinding shall be fifteen (15) 12,7mm (0,5 inch) diameter nylon 6/6 balls; the grind media shall be con

28、ditioned by soaking inwater for 7 days prior to use 3.103 standard soft test load for noise measurements the standard “soft” load for noise measurements during grinding shall be 200 grams of babycarrots 3.104 grinding operation operation cycle for the disposer in which a standard test load is ground

29、 and flushed throughthe discharge to the sewer lines with a specified water flow rate 4 Measurement methods and acoustical environmentThe clause of Part 1 is applicable except as follows:4.2 DirectmethodAddition:NOTE 101 If pure tone components are present in the noise emitted, proper precautions sh

30、ould be taken asspecified in ISO 3743-2.DD IEC/PAS 60704-2-15:2008 8 PAS 60704-2-15 IEC:2008(E)4.3 Comparison method Addition:NOTE 101 If pure tone components are present in the noise emitted, proper precautions should be taken asspecified in ISO 3743-1 and ISO 3743-2.5 Instrumentation This clause o

31、f Part 1 is applicable.6 Operation and location of appliances under testThis clause of Part 1 is applicable except as follows:6.1.3 Replacement: Prior to commencing measurements, the inside of the grind chamber shall be clean and freeof any debris from prior operation. The food waste disposer shall

32、be run through 10 completeoperational cycles, of a 30 s duration, with a hard test load (3.102). 6.1.4 Notapplicable.6.2 Supply of electric energy and of water or gas 6.2.1 Replacement: The supply voltage is measured at the plug of a non-detachable cable or cord, at theappliance inlet if a detachabl

33、e cord is provided or no cable is provided, but in no case at theentrance of extensions cables or cords.6.2.2 Notapplicable6.2.3 Notapplicable6.2.4 Replacement: The temperature of the supply water shall be between 4 C and 27 C. The flow rate of the water supply shall be 6 0,3 L/min. The water faucet

34、 shall be positionedin such a way that the water flows down the side of the sink into the drain, creating negligiblewater splash noise.6.4 Loading and operating of appliances during tests6.4.2 Replacement: The test load shall be at room temperature when the test program starts. The appliance under t

35、est shall be at room temperature when the test program starts. The appliance shall be operated according to 3.101 using each of the test loads as describedin 3.102 and 3.103. An operator shall be present to place the test load in the grind chamberand to start and stop the operational cycle of the di

36、sposer. The operators position shall bechosen to minimize the influence upon the acoustic measurement and shall be consistent forall tests.DD IEC/PAS 60704-2-15:2008PAS 60704-2-15 IEC:2008(E) 9 A 10 s measurement shall be taken that encompasses the start of the operational cycle.Upon completion of t

37、he measurements, the remaining material in the grind chamber is to beremoved and the disposer flushed with water to ensure no material remains. An auditorycheck shall be made of the unit running without any water or load to ensure that no materialremains in the grind chamber. Ensure that no test loa

38、d remains on the top lip of the grindchamber.Three trials shall be run for each type of test load and the results of each trial reported. Atleast 5 min with cold water running through the disposer shall be allowed between trials toallow the food waste disposer to return to ambient conditions.6.5 Loc

39、ation and mounting of appliances6.5.1 Not applicable.6.5.2 Notapplicable.6.5.3 Replacement: For measurements on floor-standing appliances intended for placing against a wall (includingcabinets, counters, or test enclosures for building in or under counter types) a verticalreflecting plane shall be a

40、vailable.When the measurements are made in a hard-walled test room or in a special reverberationtest room, a part of a wall of the room will serve for this purpose. The minimum area of thispart of the wall should be determined by the projection of the appliance, extended by at least0,5 m upwards and

41、 to both sides. The minimum distance between any surface of theappliance (cabinet, counter, or test enclosure) and the nearest corner of the room shallbe 1 m.When measurements are made in a free-field environment, a vertical-reflecting plane(supported by the horizontal reflecting plane) shall be pro

42、vided. The minimum size of thisvertical plane shall be at least equal to the size of the projection of the measurement surface.For both types of test environments, the requirements given below shall be followed. the acoustic absorption coefficient of the vertical reflecting plane shall be less than

43、0,06; the appliance shall be placed in the test environment without any resilient means otherthan those incorporated in the appliance; care should be taken to avoid any direct contact between the appliance (includingprotruding parts, worktops, spacers, etc.) and the vertical reflecting plane; the di

44、stance between the vertical reflecting plane and the appliance shall be establishedby placing the appliance in direct contact with the vertical reflecting plane and then movingit away a distance of 10 cm 1 cm.6.5.4 Not applicable.6.5.5 Replacement: The food waste disposer manufacturers instructions

45、regarding installation and use of thedisposer shall be followed.The test cabinet shall be constructed as shown in Figure 101.A standard laminate over particle board countertop shall be rigidly mounted to the top of thecabinet. A 838 mm 559 mm (33in 22 in), 24 gauge, double bowl stainless steel sinkD

46、D IEC/PAS 60704-2-15:2008 10 PAS 60704-2-15 IEC:2008(E) conforming to ASME A112.19.3-2000 shall be installed in the countertop as specified by the sink manufacturers instructions. The bowl depth shall be 165,1 mm (6.5 in) and each bowl 356 mm (14 in) by 400 mm (15,75 in). The drain holes shall be ce

47、ntered within each bowl. The faucet shall be deck mounted using the mounting holes provided in the sink and installed as specified by the faucet manufacturers instructions. On the underside of each sink bowl shall be two (2) 76,2 mm (3 in) 76,2 mm (3 in) damping pads aligned with the drain holes and

48、 centered between the drain holes and the front and back of the sink.The food waste disposer shall be mounted in one bowl of the sink. Each sink bowl shall have an individual P-trap, connecting to a Y- fitting. The sewer or drain line shall be connected to the Y-fitting. Cutouts may be provided in t

49、he back or lower side of the cabinet for electrical, water, and sewage connections. Care should be taken that the cutouts are the minimum size required for the services and shut by sealing means to prevent noise leakage. Care should be taken to ensure the supply lines are properly isolated to prevent transmission of structure-borne noiseThe test enclosure with appliance is to be placed as specified in 6.5.3.7 Measurement of sound pressure levels This clause of Pa