BS AU 249-1993 Specification for clutch housings for reciprocating internal combustion engines - Nominal dimensions and tolerances《往复式内燃机离合器外壳规范 标称尺寸和公差》.pdf

《BS AU 249-1993 Specification for clutch housings for reciprocating internal combustion engines - Nominal dimensions and tolerances《往复式内燃机离合器外壳规范 标称尺寸和公差》.pdf》由会员分享，可在线阅读，更多相关《BS AU 249-1993 Specification for clutch housings for reciprocating internal combustion engines - Nominal dimensions and tolerances《往复式内燃机离合器外壳规范 标称尺寸和公差》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 249:1993 ISO 7649:1991 Specification for Clutch housings for reciprocating internal combustion engines Nominal dimensions and tolerances UDC 629.114.4/.5:621.838.2BSAU249:1993 This British Standard, having been prepared under the directionof the Automobile St

2、andards Policy Committee, waspublished under the authorityof the Standards Boardand comes intoeffecton 15July1993 BSI 10-1999 The following BSI references relate to the work on this standard: Committee reference AUE/13 Draft for comment 89/80163 DC ISBN 0 580 22404 X Committees responsible for this

3、British Standard The preparation of this British Standard was entrusted by the Automobile Standards Policy Committee (AUE/-) to Technical Committee AUE/13 upon which the following bodies were represented: British Railways Board Bus and Coach Council Department of Health Department of Transport Depar

4、tment of Transport (Transport Research Laboratory) Freight Transport Association Health and Safety Executive Institute of Road Transport Engineers Lloyds Register of Shipping Ministry of Defence Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Ltd. Coopted members Amendments

5、issued since publication Amd. No. Date CommentsBSAU249:1993 BSI 10-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 Normative references 1 3 Nominal dimensions tolerances and spacing of clearance holes 1 Figure 1 Clutch housing 2 Figure 2 Bolt/screw spa

6、cing 3 Table 1 Clutch housing nominal dimensions and tolerances 4 Table 2 Bearing location diameters and associated splines 4 List of references Inside back coverBSAU249:1993 ii BSI 10-1999 National foreword This British Standard has been prepared under the direction of the Automobile Standards Poli

7、cy Committee. It is identical with ISO7649:1991 Clutch housings for reciprocating internal combustion engines Nominal dimensions and tolerances, published by the International Organization for Standardization (ISO) and in the development of which the United Kingdom played an active part. The Technic

8、al Committee has reviewed the provisions of ISO1101:1983 and SAEJ499a, to which normative reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. A British Standard does not purport to include all the necessary provisions of a contract. User

9、s of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference International Standard Corresponding British Standard ISO 286-2:1988 BS 4500 ISO limits and fits Section 1.2:1990 Tables

10、 of commonly used tolerance grades and limit deviations for holes and shafts (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may hav

11、e had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BSAU249:1993 BSI 10-1999 1 1 Scope This International Standard specifies the nominal dimensions and tolerances which affect the interchangeability between clutch housings for spring-loaded clutches

12、 and mating parts for reciprocating internal combustion engines. All other dimensions and tolerances are left to the discretion of the component manufacturer. This International Standard applies to reciprocating internal combustion engines, with the exception of engines for aircraft and passenger ca

13、rs; it may be used for other engine applications where no specific International Standard exists. Clutch housings of size codes1 to4 inTable 1 are recommended for commercial vehicles and buses. 2 Normative references The following standards contain provisions which, through reference in this text, c

14、onstitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions

15、 of the standards indicated below. Members of IECandISO maintain registers of currently valid International Standards. ISO 286-2:1988, ISO system of limits and fits Part2: Tables of standard tolerance grades and limit deviations for holes and shafts. ISO 1101:1983, Technical drawings Geometrical tol

16、erancing Tolerancing of form, orientation, location and run-out Generalities, definitions, symbols, indications on drawings. SAE J499a, Parallel side splines for soft broached holes in fittings. 3 Nominal dimensions, tolerances and spacing of clearance holes 3.1 Nominal dimensions and tolerances for

17、 the preferred sizes of clutch housings which affect interchangeability shall be as shown inTable 1 andFigure 1 andFigure 2. The flywheel housing which mates with the clutch housing shown inFigure 1 should be in accordance with ISO7648, Flywheel housings for reciprocating internal combustion engines

18、 Nominal dimensions and tolerances. 3.2 The sizes of bearing location diameters, K, and splines shall be selected fromTable 2. 3.3 For spacing of clearance holes, seeTable 1 andFigure 2. For definitions and symbols for geometrical tolerances, see ISO1101. For size code1, in the case where24 clearanc

19、e holes are required, intermediate hole positions shall be used.BSAU249:1993 2 BSI 10-1999 Figure 1 Clutch housingBSAU249:1993 BSI 10-1999 3 Figure 2 Bolt/screw spacingBSAU249:1993 4 BSI 10-1999 Table 1 Clutch housing nominal dimensions and tolerances Table 2 Bearing location diameters and associate

20、d splines Dimensions in millimetres Size code A B C F Optional F dimension for: G H L No. of clearance holes double plate clutch when extra-heavy flywheel is used clutch shaft bearing located in pilot bore of flywheel or crank-shaft end tol. a H13 a 00 787,4 g8 883 850,9 104 80 6 13,5 16 0 647,7 g8

21、711 679,45 104 80 6 13,5 16 1/2 584,2 g8 648 619,12 104 80 6 13,5 12 1 511,18 g7 553 530,22 104 137 116 80 6 11 b 12 c 2 447,68 g7 489 466,72 104 116 80 6 11 12 3 409,58 g7 451 428,62 104 80 6 11 12 4 361,95 g7 404 381 104 80 6 11 12 5 314,32 g7 356 333,38 75 58 6 11 8 6 266,7 g7 308 285,75 75 58 6

22、11 8 a See ISO 286-2. b 13,5 mm diameter may be used for high engine torque applications. c 24 clearance holes are optional for attachment to aluminium flywheel housing of size code 1. Spline profile a K J ref. mm in 20 1 3/8 SAE 10C b 25 1 1/2 25 1 3/4 25 or 30 c 2 a The use of involute splines is

23、also permitted if agreed between manufacturer and user. b This is the shape type and size specified in SAE J499a. c If a 30 mm diameter bearing bore is used, dimension G = 80 mm, Table 1, is reduced to 78 mm.BSAU249:1993 BSI 10-1999 List of references See national foreword.BS AU 249:1993 ISO 7649:19

24、91 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards a

25、re updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this B

26、ritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the lat

27、est editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those t

28、hat have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services ar

29、e also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of thes

30、e and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs a

31、nd Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of ne

32、cessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.