BS AU 215-1-1987 Power take offs (PTOs) - Specification for dimensions for clearance envelope for commercial road vehicles《动力输出装置 第1部分 商用道路车辆外廓尺寸规范》.pdf
《BS AU 215-1-1987 Power take offs (PTOs) - Specification for dimensions for clearance envelope for commercial road vehicles《动力输出装置 第1部分 商用道路车辆外廓尺寸规范》.pdf》由会员分享,可在线阅读,更多相关《BS AU 215-1-1987 Power take offs (PTOs) - Specification for dimensions for clearance envelope for commercial road vehicles《动力输出装置 第1部分 商用道路车辆外廓尺寸规范》.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU215-1: 1987 ISO7706:1985 Power take offs (PTOs) Part1: Specification for dimensions for clearance envelope for commercial road vehicles ISO title: Road vehicles Commercial vehicles Clearance envelope for power take-offs (PTO) UDC 629.114.4:629.113-494BSAU215-1
2、:1987 This BritishStandard, having been prepared under the directionof the Automobile Standards Committee, was published under the authority ofthe Board of BSI and comesintoeffect on 30January1987 BSI02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/13
3、 Draft for comment 82/79531 DC ISBN 0 580 15688 5 Committees responsible for this BritishStandard The preparation of this BritishStandard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/13, upon which the following bodies were represented: Department of Transpo
4、rt (Highways) Freight Transport Association Institute of Road Transport Engineers (Incorporated) London Regional Transport Ministry of Defence National Bus Company Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No. Date of is
5、sue CommentsBSAU215-1:1987 BSI 02-2000 i Contents Page Committees responsible Inside front cover National foreword ii 0 Introduction 1 1 Scope and field of application 1 2 Reference 1 3 General 1 4 Side-mounted PTO 2 5 Rear-mounted PTO 3 6 Designation 3 Figure 1 Clearance envelope for side-mounted P
6、TO (Type S) 2 Figure 2 Clearance envelope for rear-mounted PTO (Type Z) 3 Publication referred to Inside back coverBSAU215-1:1987 ii BSI 02-2000 National foreword This Part of BS AU215 has been prepared under the direction of the Automobile Standards Committee and is identical with ISO7706:1985 “Roa
7、d vehicles Commercial vehicles Clearance envelope for power take-offs (PTO)”, published by the International Organization for Standardization (ISO). BS AU215-2 specifies dimensions of side openings for PTOs. Terminology and conventions. The text of the International Standard has been approved as sui
8、table for publication as a BritishStandard without deviation. Some terminology and certain conventions are not identical with those used in BritishStandards; attention is drawn especially to the following. Wherever the words “International Standard” or “ISO7706” appear, referring to this standard, t
9、hey should be read as “BritishStandard” and “BS AU215-1” respectively. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer imm
10、unity from legal obligations. Cross-reference International Standard Corresponding BritishStandard ISO7804:1985 a BS AU215 Power take offs (PTOs) Part2:1987 Specification for dimensions of side openings for commercial road vehicles (Identical) a Since the issue of ISO7706, ISO7804 has been published
11、. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside
12、front cover.BSAU215-1:1987 BSI 02-2000 1 0 Introduction It should be appreciated that the requirements of this International Standard did not necessarily reflect current practice at the time of its preparation, but it is recommended that, in the interest of interchangeability for the future, its pro
13、visions should be adopted for new designs. The clearance envelope which is specified should meet most requirements, but if, for any reason, they are not suitable, the vehicle manufacturer and the PTO manufacturer will have to find an alternative solution which is acceptable to both. 1 Scope and fiel
14、d of application This International Standard lays down the dimensions of clearance envelopes for regular and heavy duty type truck transmission power take-offs. It is applicable to clearance envelopes required immediately adjacent to the PTO openings or drives on truck transmissions. 2 Reference ISO
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSAU21511987POWERTAKEOFFSPTOSSPECIFICATIONFORDIMENSIONSFORCLEARANCEENVELOPEFORCOMMERCIALROADVEHICLES
链接地址:http://www.mydoc123.com/p-547799.html