BS A 358-3-2000 MJ threads - Limit dimensions for fittings for fluid systems《MJ螺纹 流体系统用的接头的极限尺寸》.pdf

《BS A 358-3-2000 MJ threads - Limit dimensions for fittings for fluid systems《MJ螺纹 流体系统用的接头的极限尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS A 358-3-2000 MJ threads - Limit dimensions for fittings for fluid systems《MJ螺纹 流体系统用的接头的极限尺寸》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD AEROSPACE SERIES BS A 358

2、-3:2000 ISO 5855-3:1999 ICS 49.030.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW MJ threads Part 3: Limit dimensions for fittings for fluid systemsThis British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the

3、authority of the Standards Committee and comes into effect on 15 January 2000 BSI 01-2000 ISBN 0 580 34017 1 BS A 358-3:2000 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard reproduces verbatim ISO 5855-3:1999 and implements it as the UK national sta

4、ndard. It supersedes BS 6293-3:1994 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee ACE/12, Aerospace fasteners and fastening systems, to Subcommittee ACE/12/1, Aerospace fasteners and fastening systems (International), which has the responsibility to

5、: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organ

6、izations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Stan

7、dards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Stand

8、ard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, page ii, pages 1 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the docum

9、ent was last issued.A Referencenumbe r ISO58553:1999 (E) INTERNATIONAL STANDARD ISO 58553 Secondedition 19991015 AerospaceMJthreads Part3: Limitdimensionsforfittingsforfluidsystems AronautiqueetespaceFiletageMJ Partie3:Dimensionslimitespourraccordementsdesystmesdefluides BS A 358-3:2000)E(9991:35585

10、OSI ii Foreword ISO (the InternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestabl

11、ishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnongovernmental,in liaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization. InternationalStandardsaredraftedi

12、naccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtoth ememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote. InternationalStandardISO 58553waspreparedbyTech

13、nica lCommitteeISO/TC 20,Aircraftandspacevehicles , SubcommitteeSC4, Aerospacefastenersystems . Thissecondeditioncancelsandreplacesthefirstedition(ISO 58553:1988),ofwhichitconstitutes atechnical revision. ISO5855consistsofthefollowingparts,underthegeneraltitle AerospaceMJthreads : Part1:Generalrequi

14、rements Part2:Limitdimensionsforboltsandnuts Part3:Limitdimensionsforfittingsforfluidsystems BS A 358-3:2000DRADNATSLANOITANRETNI OSI )E(9991:35585OSI 1 AerospaceMJthreads Part3: Limitdimensionsforfittingsforfluidsystems 1Scope ThispartofISO5855specifieslimitdimensionsofMJthreadsforfluidsystemsfitti

15、ngsforaerospaceconstruction. 2Normative references Thefollowingnormativedocumentscontainprovisionswhich,throughreferenceinthistext,constituteprovisionsofthis partofISO5855.Fordatedreferences,subs equentamendmentsto,orrevisionsof,anyofthesepublicationsdonot apply.However,partiestoagreementsbasedonthi

16、spartofISO 5855areencour agedtoinvestigatethepossibilityof applyingthemostrecenteditionofthenormativedocumentsindicatedbelow.Forundatedreferences,thelatestedition ofthenormativedocumentreferredtoapplies.MembersofISOandIECmaintainregistersofcurrentlyvalid InternationalStandards. ISO9651:1998, ISOgene

17、ralpurposemetricscrewthreadsTolerancesPart1:Principlesandbasicdata. ISO58551:1999, AerospaceMJthreadsPart1:Generalrequirements. 3 Nominaldiametersandpitches SeeTable1. Table1Nominaldiametersandpitches Dimensionsinmillimetres Nominaldiameter d or D Pitch P Nominaldiameter d or D Pitch P 812 7 10 30 1

18、2 1,25 33 1,5 14 36 16 39 18 1,5 42 20 48 2 22 50 24 BS A 358-3:2000)E(9991:35585OSI OSI 2 4Tolerance classes SeeTable2. Table2Toleranceclasses Assembly Externalthreads Internalthreads Generalcase(clearance d 6h D 1 5H maybenil) d 2 4h D 2 4H Requiringsystematic d 6g D 1 5H clearance d 2 4g D 2 4H 5

19、 Provisionsforcoatedthreads Beforecoating,thedimensionsofthethreadsshallbecompatiblewiththethicknessofthecoatingselectedand withthelimitdimensionsforfinishedpartsspecifiedinclause6. 6 Limitdimensionsforfinishedparts(coatedoruncoated) 6.1External threads 6.1.1 4h6hexternalthreads Figure1illustratesth

20、epositionandtheformofthelimitprofiles(maximumandminimum)inrelationtothebasic profile(seeISO58551). Tables3and4specifythelimitdimensions. a Pitch D P b Basicandmaximumprofiles c Basicprofile d Minimumprofile Figure1Limitprofilesforexternalthreads (clearancemaybenil) BS A 358-3:2000OSI )E(9991:35585OS

21、I 3 Table3Limitdimensionsfor4h6hexternalthreads Dimensionsinmillimetres Threaddesignation Majordiameter d Pitchdiameter d 2 Minordiameter d 3 T d T d2 T d3 max. min. (6h) a max. min. (4h) a max. min. MJ8 14h6h 8,00 7,82 0,18 7,350 7,279 0,071 6,845 6,713 0,132 MJ10 14h6h 10,00 9,82 0,18 9,350 9,279

22、0,071 8,845 8,713 0,132 MJ12 1,254h6h 12,000 11,788 0,212 11,188 11,103 0,085 10,557 10,396 0,161 MJ14 1,54h6h 14,000 13,764 0,236 13,026 12,936 0,09 12,268 12,087 0,181 MJ16 1,54h6h 16,000 15,764 0,236 15,026 14,936 0,09 14,268 14,087 0,181 MJ18 1,54h6h 18,000 17,764 0,236 17,026 16,936 0,09 16,268

23、 16,087 0,181 MJ20 1,54h6h 20,000 19,764 0,236 19,026 18,936 0,09 18,268 18,087 0,181 MJ22 1,54h6h 22,000 21,764 0,236 21,026 20,936 0,09 20,268 20,087 0,181 MJ24 1,54h6h 24,000 23,764 0,236 23,026 22,931 0,095 22,268 22,082 0,186 MJ27 1,54h6h 27,000 26,764 0,236 26,026 25,931 0,095 25,268 25,082 0,

24、186 MJ30 1,54h6h 30,000 29,764 0,236 29,026 28,931 0,095 28,268 28,082 0,186 MJ33 1,54h6h 33,000 32,764 0,236 32,026 31,931 0,095 31,268 31,082 0,186 MJ36 1,54h6h 36,000 35,764 0,236 35,026 34,931 0,095 34,268 34,082 0,186 MJ39 1,54h6h 39,000 38,764 0,236 38,026 37,931 0,095 37,268 37,082 0,186 MJ42

25、 24h6h 42,00 41,72 0,28 40,701 40,595 0,106 39,691 39,463 0,228 MJ48 24h6h 48,00 47,72 0,28 46,701 46,589 0,112 45,691 45,457 0,234 MJ50 24h6h 50,00 49,72 0,28 48,701 48,589 0,112 47,691 47,457 0,234 a InaccordancewithISO9651 Table4Rootradiiforexternalthreads Dimensionsinmillimetres Pitch P Rootradi

26、us R max. min. 1 0,18 0,15 1,25 0,226 0,188 1,5 0,271 0,225 2 0,361 0,300 6.1.2 4g6gexternalthreads Figure2illustratesthepositionandtheformofthelimitprofiles(maximumandminimum)inrelationtothebasic profile(seeISO58551). Tables4and5specifythelimitdimensions. BS A 358-3:2000)E(9991:35585OSI OSI 4 a Pit

27、ch D P b Basicprofile c Maximumprofile d Minimumprofile e es isthebasicupperdeviation,seeISO9651 Figure2Limitprofilesforexternalthreads (systematicclearance) Table5Limitdimensionsfor4g6gexternalthreads Dimensionsinmillimetres Threaddesignation Majordiameter d Pitchdiameter d 2 Minordiameter d 3 T d

28、T d2 T d3 max. min. (6g) a max. min. (4g) a max. min. MJ8 14g6g 7,974 7,794 0,18 7,324 7,253 0,071 6,819 6,687 0,132 MJ10 14g6g 9,974 9,794 0,18 9,324 9,253 0,071 8,819 8,687 0,132 MJ12 1,254g6g 11,972 11,760 0,212 11,160 11,075 0,085 10,529 10,368 0,161 MJ14 1,54g6g 13,968 13,732 0,236 12,994 12,90

29、4 0,09 12,236 12,055 0,181 MJ16 1,54g6g 15,968 15,732 0,236 14,994 14,904 0,09 14,236 14,055 0,181 MJ18 1,54g6g 17,968 17,732 0,236 16,994 16,904 0,09 16,236 16,055 0,181 MJ20 1,54g6g 19,968 19,732 0,236 18,994 18,904 0,09 18,236 18,055 0,181 MJ22 1,54g6g 21,968 21,732 0,236 20,994 20,904 0,09 20,23

30、6 20,055 0,181 MJ24 1,54g6g 23,968 23,732 0,236 22,994 22,899 0,095 22,236 22,050 0,186 MJ27 1,54g6g 26,968 26,732 0,236 25,994 25,899 0,095 25,236 25,050 0,186 MJ30 1,54g6g 29,968 29,732 0,236 28,994 28,899 0,095 28,236 28,050 0,186 MJ33 1,54g6g 32,968 32,732 0,236 31,994 31,899 0,095 31,236 31,050

31、 0,186 MJ36 1,54g6g 35,968 35,732 0,236 34,994 34,899 0,095 34,236 34,050 0,186 MJ39 1,54g6g 38,968 38,732 0,236 37,994 37,899 0,095 37,236 37,050 0,186 MJ42 24g6g 41,962 41,682 0,28 40,663 40,557 0,106 39,653 39,425 0,228 MJ48 24g6g 47,962 47,682 0,28 46,663 46,551 0,112 45,653 45,419 0,234 MJ50 24

32、g6g 49,962 49,682 0,28 48,663 48,551 0,112 47,653 47,419 0,234 a InaccordancewithISO9651 BS A 358-3:2000OSI )E(9991:35585OSI 5 6.2Internal threads Figure3illustratesthepositionandtheformofthelimitprofiles(maximumandminimum)inrelationtothebasic profile(seeISO58551). Table6specifiesthelimitdimensions.

33、 a Pitch D P b Basicprofile c Maximumprofile d Basicandminimumprofiles Figure3 Limitprofilesforinternalthreads BS A 358-3:2000)E(9991:35585OSI OSI 6 Table6Limitdimensionsfor4H5Hinternalthreads Dimensionsinmillimetres Major diameter Pitchdiameter Minordiameter Thread D 3 a D 2 D 1 designation T D2 T

34、D1 max. max. min. (4H) b max. min. (5H) b MJ8 14H5H 8,239 7,445 7,350 0,095 7,216 7,026 0,19 MJ10 14H5H 10,239 9,445 9,350 0,095 9,216 9,026 0,19 MJ12 1,254H5H 12,292 11,300 11,188 0,112 10,994 10,782 0,212 MJ14 1,54H5H 14,335 13,144 13,026 0,118 12,775 12,539 0,236 MJ16 1,54H5H 16,335 15,144 15,026

35、 0,118 14,775 14,539 0,236 MJ18 1,54H5H 18,335 17,144 17,026 0,118 16,775 16,539 0,236 MJ20 1,54H5H 20,335 19,144 19,026 0,118 18,775 18,539 0,236 MJ22 1,54H5H 22,335 21,144 21,026 0,118 20,775 20,539 0,236 MJ24 1,54H5H 24,342 23,151 23,026 0,125 22,775 22,539 0,236 MJ27 1,54H5H 27,342 26,151 26,026

36、 0,125 25,775 25,539 0,236 MJ30 1,54H5H 30,342 29,151 29,026 0,125 28,775 28,539 0,236 MJ33 1,54H5H 33,342 32,151 32,026 0,125 31,775 31,539 0,236 MJ36 1,54H5H 36,342 35,151 35,026 0,125 34,775 34,539 0,236 MJ39 1,54H5H 39,342 38,151 38,026 0,125 37,775 37,539 0,236 MJ42 24H5H 42,429 40,841 40,701 0

37、,14 40,351 40,051 0,3 MJ48 24H5H 48,439 46,851 46,701 0,15 46,351 46,051 0,3 MJ50 24H5H 50,439 48,851 48,701 0,15 48,351 48,051 0,3 a D 3 min.isnotspecified.However,itshallbegreaterthan D(seeFigure3). b InaccordancewithISO9651 6.3 Maximumpermissibledeviationsonpitch(lead)andonhalfflankangle Valuesgi

38、veninTable7havebeentakenfromTable6ofISO58551:1999. Table7Maximumpermissibledeviationsonpitch(lead)andonhalfflankangle Nominaldiameter Pitch Externalthread Internalthread d or D P DP Da DP Da mm mm mm mm 8 1 16,4 1 5 21,9 1 27 10 12 1,25 19,6 1 2 25,9 1 22 14 16 18 20,8 0 55 27,3 1 12 20 22 24 1,5 27

39、 30 21,9 0 58 28,9 1 16 33 36 39 42 24,5 0 49 32,3 1 4 48 2 25,9 0 51 34,6 1 8 50 BS A 358-3:2000BS A 358-3:2000 ISO 5855-3:1999 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

40、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the in

41、ternational level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services

42、. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individ

43、ual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response

44、to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its

45、 Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standa

46、rds developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduce