BS 6955-16-1994 Calibration of vibration and shock pick-ups - Method of test for mounting torque sensitivity《振动和冲击传感器的校准 安装扭矩灵敏度的试验方法》.pdf

《BS 6955-16-1994 Calibration of vibration and shock pick-ups - Method of test for mounting torque sensitivity《振动和冲击传感器的校准 安装扭矩灵敏度的试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS 6955-16-1994 Calibration of vibration and shock pick-ups - Method of test for mounting torque sensitivity《振动和冲击传感器的校准 安装扭矩灵敏度的试验方法》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS6955-16: 1994 ISO5347-16: 1993 Calibration of vibration and shock pick-ups Part 16: Method of test for mounting torque sensitivity UDC 534.1:681.327.7:53.089.6BS6955-16:1994 This British Standard, having been prepared under the directionof the General Mechanical Engineering Standa

2、rds Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15 March 1994 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference GME/21 Draft for comment 87/72304 DC ISBN 0 580 23088 0 Committees responsible for this

3、 British Standard The preparation of this British Standard was entrusted by the General Mechanical Engineering Standards Policy Committee (GME/-) to Technical Committee GME/21, upon which the following bodies were represented: Electricity Association Federation of Civil Engineering Contractors Imper

4、ial College of Science and Technology Institute of Sound and Vibration Research Institution of Mechanical Engineers Lloyds Register of Shipping Ministry of Defence Open University Power Generation Contractors Association PGCA (BEAMA Ltd.) Railway Industry Association of Great Britain Sira Test and C

5、ertification Ltd. Society of British Aerospace Companies Limited The following bodies were also represented in the drafting of the standard, through subcommittees and panels: British Coal Corporation Health and Safety Executive Society of Environmental Engineers University of Cranfield Amendments is

6、sued since publication Amd. No. Date CommentsBS6955-16:1994 BSI 11-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 Normative reference 1 3 Apparatus 1 4 Method 1 List of references Inside back coverBS6955-16:1994 ii BSI 11-1999 National foreword This P

7、art of BS 6955 has been prepared under the direction of the General Mechanical Engineering Standards Policy Committee. It is identical with ISO5347-16:1993 Methods for the calibration of vibration and shock pick-ups Part 16: Testing of mounting torque sensitivity, published by the InternationalOrgan

8、ization for Standardization (ISO). ISO 5347-16 was prepared by Technical Committee ISO/TC 108, Mechanical vibration and shock, in which the UK played an active part. BS 6955 consists of the following Parts, which are identical with the corresponding Parts of ISO 5347: Part 0: Guide to basic principl

9、es; Part 1: Methods for primary vibration calibration by laser interferometry; Part 2: Method for primary shock calibration by light cutting; Part 3: Method for secondary vibration calibration; Part 4: Method for secondary shock calibration; Part 5: Method for calibration by Earths gravitation; Part

10、 6: Method for primary vibration calibration at low frequencies; Part 7: Methods for primary calibration by centrifuge; Part 8: Method for primary calibration by dual centrifuge; Part 9: Method for secondary vibration calibration by comparison of phase angles; Part 10: Method for primary calibration

11、 by high impact shocks; Part 11: Method of test for transverse vibration sensitivity; Part 12: Method of test for transverse shock sensitivity; Part 13: Method of test for base strain sensitivity; Part 14: Method of test for resonance frequency of undamped accelerometers on a steel block; Part 15: M

12、ethod of test for acoustic sensitivity; Part 16: Method of test for mounting torque sensitivity; Part 17: Method of test for fixed temperature sensitivity; Part 18: Method of test for transient temperature sensitivity; Part 19: Method of test for magnetic field sensitivity. Part 20 of ISO 5347 is in

13、 preparation. It is envisaged that when it is published it will be implemented as Part 20 of BS 6955. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standar

14、d does not of itself confer immunity from legal obligations. Cross-reference International Standard Corresponding British Standard ISO 5347-3:1993 BS 6955 Calibration of vibration and shock pick-ups Part 16:1994 Methods for secondary vibration calibration (Identical) Summary of pages This document c

15、omprises a front cover, an inside front cover, pagesi andii, pages1and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS6955-16:1994 BSI 11

16、-1999 1 1 Scope ISO 5347 comprises a series of documents dealing with methods for the calibration of vibration and shock pick-ups. This part of ISO 5347 lays down detailed specifications for the instrumentation and procedure to be used for mounting torque sensitivity testing. It applies to pick-ups

17、that are mounted by screws, bolts or other threaded fasteners. The change in calibration factor due to the mounting torque is determined. This part of ISO 5347 is applicable for a mounting torque range of one-half of the specified value, the specified value and twice the value of the specified mount

18、ing torque. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this part of ISO 5347. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on t

19、his part of ISO 5347 are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 5347-3:1993, Methods for the calibration of vibration and shock pick-ups P

20、art 3: Secondary vibration calibration. 3 Apparatus 3.1 Equipment capable of maintaining room temperature at 23 C 3 C. 3.2 Vibration equipment, complying with the requirements specified for secondary vibration calibration (see ISO 5347-3). The thickness of the steel fixture on which the pick-up is t

21、o be mounted shall be at least three times the length of the mounting screws, with a minimum plate thickness of 20 mm. The surface of the fixture shall have a roughness value, expressed as the arithmetical mean deviation, R a , 1 4m. The flatness shall be such that the surface shall be contained bet

22、ween two parallel planes 5 4m apart. The drilled and tapped holes for connecting the pick-up shall have a perpendicularity tolerance to the surface of less than 10 4m, i.e. the centreline ofthe hole shall be contained in a cylindrical zone of104m diameter and a height equal to the hole depth. 3.3 To

23、rque-measuring equipment, giving a maximum total mounting torque error 15% of reading. 4 Method 4.1 Test procedure The interface and thread lubrication normally recommended shall be used and stated. The torque shall be applied from zero torque to each of the three test torques (see clause 1) in one

24、continuous procedure. Determine the calibration factor for the reference frequency and the reference amplitude for the three test torques. 4.2 Expression of results Calculate the torque sensitivity, S T , expressed as a percentage, using the following formula: where The maximum value for the torque

25、sensitivity shall be reported. S x is the calibration factor at one-half of or at twice the specified mounting torque; S is the calibration factor at the specified mounting torque. S T S x S S - 100 =2 blankBS6955-16:1994 BSI 11-1999 List of references See national foreword.BS6955-16: 1994 ISO5347-1

26、6: 1993 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStanda

27、rds are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using t

28、his BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive th

29、e latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of th

30、ose that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information servic

31、es are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of

32、 these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Desi

33、gns and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard,

34、of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.