BS 5131-3 7-1991 Methods of test for footwear and footwear materials - Uppers textiles and threads - Breaking strength of shoe laces《鞋靴和鞋靴材料试验方法 第3部分 鞋帮、织物和缝线 第7节 鞋带断裂强度》.pdf

《BS 5131-3 7-1991 Methods of test for footwear and footwear materials - Uppers textiles and threads - Breaking strength of shoe laces《鞋靴和鞋靴材料试验方法 第3部分 鞋帮、织物和缝线 第7节 鞋带断裂强度》.pdf》由会员分享，可在线阅读，更多相关《BS 5131-3 7-1991 Methods of test for footwear and footwear materials - Uppers textiles and threads - Breaking strength of shoe laces《鞋靴和鞋靴材料试验方法 第3部分 鞋帮、织物和缝线 第7节 鞋带断裂强度》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 5131-3.7: 1991 Methods of test for Footwear and footwear materials Part 3: Uppers, textiles and threads Section 3.7 Breaking strength of shoe laces NOTEIt is recommended that this Section should be read in conjunction with BS5131-0, published separately.BS5131-3.7:1991 This Briti

2、sh Standard, having been prepared under the directionof the Textiles and Clothing Standards Policy Committee, was published under the authority of the Board ofBSI and comes into effect on 31January 1991 BSI 10-1999 First published January 1979 Second edition January 1991 The following BSI references

3、 relate to the work on this standard: Committee reference TCM/39 Draft for comment 89/36224 DC ISBN 0 580 18821 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Textiles and Clothing Standards Policy Committee (TCM/-) to Technical Commi

4、ttee TCM/39, upon which the following bodies were represented: British Footwear Manufacturers Federation British Leather Confederation British Rubber Manufacturers Association British Steel plc Consumer Standards Advisory Committee of BSI Cork Industry Federation Footwear Components Federation Footw

5、ear Distributors Federation Institute of Trading Standards Administration Iron and Steel Trades Confederation Lancashire Footwear Manufacturers Association Mail Order Traders Association of Great Britain Ministry of Defence National Union of Footwear, Leather and Allied Trades Office of Fair Trading

6、 SATRA Footwear Technology Centre The following bodies were also represented in the drafting of the standard, through subcommittees and panels: British Adhesives and Sealants Association British Paper and Board Industry Federation British Plastics Federation Multiple Shoe Retailers Association RAPRA

7、 Technology Ltd. Amendments issued since publication Amd. No. Date CommentsBS5131-3.7:1991 BSI 10-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Principle 1 3 Apparatus 1 4 Conditioning 1 5 Preparation of test specimens 1 6 Procedure 1 7 Calculation and expres

8、sion of results 1 8 Test report 1BS5131-3.7:1991 ii BSI 10-1999 Foreword This Section of BS5131 has been prepared under the direction of the Textiles and Clothing Standards Policy Committee. It supersedes BS5131-3.7:1979, which is withdrawn. A British Standard does not purport to include all the nec

9、essary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, page1

10、and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS5131-3.7:1991 BSI 10-1999 1 1 Scope This Section of BS5131 describes a method for the determination of the breakin

11、g strength of shoe laces both in equilibrium with a reference atmosphere and also in the wet state. 2 Principle Test specimens, cut from the shoe laces, are tested in a tensile testing machine. The force required to break the test specimen is determined. 3 Apparatus 1) 3.1 Conditioning cabinet or ro

12、om, maintaining an atmosphere of20 2 C and652%r.h. 3.2 A tensile testing machine, having a rate of traverse of100 20mm/min. A force range of0N to1000N (0kgf to100kgf) is suitable for most shoe laces though some of the strongest may give breaking strengths up to about1500N (150kgf). The machine provi

13、des means for gripping the shoe laces securely without inducing jaw breaks. Suitable gripping devices are bollards or serrated or rubber covered jaws. 4 Conditioning Where the shoe laces are to be tested by the dry test method (6.2), place them in the conditioning cabinet or room (3.1). After48h, cu

14、t the test specimens (seeclause5). Carry out the test in this atmosphere. Where the shoe laces are to be tested by the wet test method (6.3), do not condition them. 5 Preparation of test specimens Cut three lengths of shoe lace which are sufficiently long to allow for a test length of200mm between t

15、he grips on the tensile testing machine (3.2). If the test material is supplied as made-up shoe laces, cut each test specimen from a different shoe lace. 6 Procedure 6.1 General Select the appropriate bollards or jaws and fit them to the tensile testing machine (3.2). NOTEA preliminary test to deter

16、mine the most suitable type of clamp is recommended. 6.2 Dry test method Clamp the test specimen in the bollards or jaws so that there is a distance of200mm between the edges of the clamps in the bollards or between the edges of the jaws. Run the machine at a rate of traverse of100mm/min and note th

17、e force required to break the test specimen. Test the other two test specimens in the same way. If any of the test specimens breaks at the jaws, reject these results and carry out further tests on new test specimens until three results are obtained for test specimens which do not break at the jaws.

18、6.3 Wet test method Soak the test specimens in distilled or de-ionized water at20 C for1h. Where complete wetting of test specimens that are normally resistant to wetting is essential, use an aqueous solution containing not more than1g/L of a non-ionic wetting agent instead of water. While the test

19、specimens are still wet, determine the force required to break them using the method described in6.2. 7 Calculation and expression of results Calculate the arithmetic mean of the three results obtained using the methods described in clause6. Use this to express the mean breaking strength of the test

20、 material. 8 Test report The test report shall include the following items: a) results expressed in accordance with clause7, including an indication as to whether the tests were carried out with the shoe laces in the wet or dry state; b) nature and full identification of the sample(s); c) reference

21、to this method of test, i.e. BS5131-3.7; d) date of testing. 1) For information on the availability of suitable apparatus to perform this test, apply to Enquiry Section, BSI, Linford Wood, Milton Keynes, MK146LE quoting the number of this standard and the clause number referring to the items concern

22、ed. Enclose a stamped addressed envelope for reply.BS 5131-3.7: 1991 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level.

23、 It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be gratef

24、ul if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called

25、 PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international stand

26、ards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to

27、 Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial

28、 discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standard

29、ization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclu

30、de the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.