BS 3SP 3-1943 Specification for aircraft material - Fork joints (low tensile type) (for sizes No 4 B A to 1 2 inch B S F inclusive)《航空器材料规格 叉形接头(低强度型)(尺寸从No 4 B A 至含1 2 in B S F )》.pdf
《BS 3SP 3-1943 Specification for aircraft material - Fork joints (low tensile type) (for sizes No 4 B A to 1 2 inch B S F inclusive)《航空器材料规格 叉形接头(低强度型)(尺寸从No 4 B A 至含1 2 in B S F )》.pdf》由会员分享,可在线阅读,更多相关《BS 3SP 3-1943 Specification for aircraft material - Fork joints (low tensile type) (for sizes No 4 B A to 1 2 inch B S F inclusive)《航空器材料规格 叉形接头(低强度型)(尺寸从No 4 B A 至含1 2 in B S F )》.pdf(12页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD CONFIRMED APRIL 1998 BS 3SP 3:1943 Incorporating Amendment Nos. 1, 2 and 3 (Cancelling BS Specification 2 SP 3.) Specification for Aircraft Material Fork joints (lowtensile type) (forsizes No.4B.A. to 1 / 2inch B.S.F. inclusive) NOTEThe Institution desires to call attention to the f
2、act that this Specification is intended to include the technical provisions necessary for the supply of the articles herein referred to, but does not purport to comprise all the necessary provisions of a contract. UDC 629.13.01:621.825.6BS3SP3:1943 This Specification having been approved by the Airc
3、raft IndustryCommittee was published by theauthority of theCouncil of theInstitution asaBritishStandard on 19 February 1943 BSI 05-2000 ISBN 0 580 34456 8 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their c
4、orrect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 7 and a back cover. This standard has been updated (see copyright date) and may
5、have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue Comments 632 May 1947 6218 July 1967 1797 August 1975 Indicated by a sideline in the marginBS3SP3:1943 BSI 05-2000 i Contents Page 1 M
6、anufacture 1 2 Screw threads 1 3 Anti-Corrosion treatment 1 4 Selection for testing 1 5 Mechanical test 1 6 Marking 1 7 Material 1 8 Manufacture 1 9 Design and dimensions 1 10 Material 1 11 Manufacture 2 12 Design and dimensions 2 13 Freedom from defects 2 14 Heat treatment 2 15 Selection and prepar
7、ation of mechanical test samples 2 16 Mechanical tests 2 17 Hardness tests 3 18 Magnetic crack detection 3 Table 1 Fork Joints 4 Table 2 Alternative design of low tensile fork joints for use with the “cold heading” process of manufacture 6ii blankBS3SP3:1943 BSI 05-2000 1 NOTEThe order must state th
8、e material classification letter and part number of the fork joints required in accordance withclause5. 1 Manufacture Fork joints may, at the option of the manufacturer, be made by machining either from bar or from blanks produced by the “cold heading” process. Theyshall be tapped either right hand
9、or left handas specified on the order. 2 Screw threads The screw threads of coated fork joints in non-corrosion resisting steel and those of fork joints in corrosion resisting steel shall not be smaller than the minimum full, effective and core diameters specified in TableIII of BS Specification No.
10、93 forBritish Association Threads, or Table12 of BSSpecification No.84 for British Standard Fine Threads. The screw threads of all fork joints (thosein non-corrosion resisting steel after being coated) shall be required to pass approved gauges. 3 Anti-Corrosion treatment All parts in non-corrosion r
11、esisting steel shall be uniformly coated with cadmium in accordance withthe requirements of specification DTD904 1) . 4 Selection for testing Samples of fork joints may be selected at the discretion of the Inspector and tested as specified inClause5. 5 Mechanical test The finished fork joints select
12、ed as specified in Clause 4 shall be screwed on to the wire as far as the inspection hole and the axial load shall be applied to a pin placed through the holes in the fork joint, no part of the fork joint being gripped in the testing machine. When loaded in this manner the fork joints shall show an
13、ultimate tensile strength notless than that given inTable 1 (Col. 23) andTable 2 (Col. 23). 6 Marking All fork joints shall have the appropriate part number applied on the shank near the tapped endby rolling and shall also bear the mark of the Inspector. If made of corrosion resisting steel they sha
14、ll in addition be marked with the letter “Z” preceding the part number. NOTEFor ordering purposes a letter “Y” shall be inserted in the Part Reference Number for non-corrosion resisting fork joints between the Specification Number and Part Number so as to distinguish clearly between non-corrosion re
15、sisting and corrosion resisting parts. For example, the complete Part Reference Number for 7 / 16in. non-corrosion resisting fork joint (left-hand thread) isS.P. 3Y/420L and for corrosion resisting steel S.P. 3Z/420L, while the corresponding markings on the actual fork joint willbe420L and Z/420L. F
16、ORK JOINTS MACHINED FROM BAR. 7 Material Fork joints machined from bar shall be made from steel bars which have been inspected and passed by the Inspector as complying with the latest issue ofBS Specification S. 1 or S. 96, or where corrosion resisting steel is specified from the latest issue of one
17、 of the following BS Specifications, S. 61, S. 62 orS. 80. 8 Manufacture Fork joints shall be machined bright all over. 9 Design and dimensions All fork joints (those in non-corrosion resisting steel after coating) shall be in accordance with the dimensions and limits given inTable 1 andTable 2, wit
18、h the exception that those made in corrosion resisting steel shall have the collar (D) and projection (W) omitted. FORK JOINTS MADE BY THE “COLDHEADING” PROCESS (forSIZES 4 B.A. to 3 / 16 in. ONLY). 10 Material a) The fork joints shall be machined from blanks made from steel of the following chemica
19、l compositions 2) : b) The complete analysis of every cast shall be supplied to the Inspector. 1) Ministry of Technology, Process Specification DTD 904 for cadmium plating. Carbon not less than 0.25 nor more than0.35 per cent. Silicon not less than 0.10 nor more than0.35 per cent. Manganese not less
20、 than 0.50 nor more than0.90 per cent. Sulphur not more than 0.06 per cent. Phosphorus not more than 0.06 per cent. 2) Steel of this composition is covered by BS 970 En. 5.BS3SP3:1943 2 BSI 05-2000 c) When corrosion resisting steel fork joints are required, the steel shall comply with the chemical c
21、omposition S. 61, S. 62 or S. 80. 3) 11 Manufacture The blanks shall be made by an approved process from material in a suitably softened condition. 12 Design and dimensions All fork joints (those in non-corrosion resisting steel after coating) shall be in accordance with the dimensions and limits gi
22、ven inTable 2, with the exception that those made in corrosion resisting steel shall have the projection (W) omitted. 13 Freedom from defects a) The fork joints shall be free from defects. b) Any fork joint may be rejected at any time forfaults in manufacture notwithstanding thatit has been passed p
23、reviously on chemical composition and mechanical tests. 14 Heat treatment a) All blanks before machining shall be hardened and tempered to the required ultimate strength. b) No blanks shall be re-hardened more than three times. 15 Selection and preparation of mechanical test samples a) Blanks harden
24、ed and tempered by a continuous process. During each period of continuous heat treatment not exceeding8hours, at least one test sample shall be selected. This test sample shall be either one of the blanks of the largest diameter that has been treated during this period or a length of wire from which
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS3SP31943SPECIFICATIONFORAIRCRAFTMATERIALFORKJOINTSLOWTENSILETYPEFORSIZESNO4BATO12INCHBSFINCLUSIVE 航空器

链接地址:http://www.mydoc123.com/p-544112.html