BS 2S 135-1977 Specification for 1% carbon-chromium steel billets bars forgings and parts (limiting ruling section 25 mm)《含1%碳-铬钢坯、棒材、锻件及零件规范 (限定划线部位25mm)》.pdf

《BS 2S 135-1977 Specification for 1% carbon-chromium steel billets bars forgings and parts (limiting ruling section 25 mm)《含1%碳-铬钢坯、棒材、锻件及零件规范 (限定划线部位25mm)》.pdf》由会员分享，可在线阅读，更多相关《BS 2S 135-1977 Specification for 1% carbon-chromium steel billets bars forgings and parts (limiting ruling section 25 mm)《含1%碳-铬钢坯、棒材、锻件及零件规范 (限定划线部位25mm)》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS 2S 135:1977 Incorporating Amendment No. 1 Specification for 1 % carbon-chromium steel billets, bars, forgings and parts (Limiting ruling section 25 mm) UDC 629.7:669.15 784 26-4 BS 2S 135:1977 This British Standard, having been prepared under the direction of the

2、 Aerospace Standards Committee, was published under the authority of the Executive Board on 29 April 1977 BSI 30 May 2003 The following BSI references relate to the work on this standard: Committee reference ACE/15 Draft for comment 75/76712 DC ISBN 0 580 09612 2 This publication does not purport to

3、 include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1

4、 and 2, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Sidelining in this document indicates the most recent changes by amendment. Amendments issued since publication Amd. No. Date of issue Comments 14141 30 May

5、 2003 Indicated by a sidelineBS 2S 135:1977 BSI 30 May 2003 i Contents Page 1 Inspection and testing procedure 1 2 Manufacture 1 3 Chemical composition 1 4 Surface dressing 2 5 Condition 2 6 Heat treatment 2 7 Mechanical properties 2ii blankBS 2S 135:1977 BSI 30 May 2003 1 1 Inspection and testing p

6、rocedure 1.1 General This British Standard shall be used in conjunction with the relevant sections of the latest issue of BS S 100 as follows: 1.2 Sulphur printing or deep etching tests One sample shall be taken from each ingot for sulphur printing or deep etching tests. 1.3 Ultrasonic examination T

7、he material shall be ultrasonically tested in accordance with BS S 100, Annex B. 1.4 Decarburization If required, examination for and the amount of decarburization shall be agreed between the manufacturer and the purchaser. 1.5 Cleanness The material shall be assessed for micro-cleanness in accordan

8、ce with BS S 100, to the acceptance criteria stated below: 2 Manufacture The material shall be manufactured by an electric process and shall be vacuum degassed. 3 Chemical composition The steel shall contain: Bars for machining delivered in other than the finally heat treated condition sections 1 an

9、d 2 Forging stock and billets and bars for subsequent working sections 1 and 5 Forgings sections 1 and 6 Parts finally heat treated after machining sections 1 and 7 ASTM E 45-97: Method A Plate I-r Inclusion type A B C D Thin Heavy Thin Heavy Thin Heavy Thin Heavy Worst field severity per specimen 2

10、.5 1.5 2 0.5 0 0 1 0.5 Average of all results per cast tested 2.5 1.5 2 0.5 0 0 1 0.5 Element % min. max. Carbon Silicon Manganese Phosphorus Sulphur Chromium Copper Molybdenum Nickel Vanadium 0.90 0.15 0.25 1.3 1.10 0.40 0.55 0.030 0.025 1.6 0.25 0.1 0.4 0.3BS 2S 135:1977 2 BSI 30 May 2003 4 Surfac

11、e dressing The material shall be overall dressed. 5 Condition 5.1 The material shall be supplied in the appropriate condition stated below. 5.2 Parts shall be supplied finally heat treated. 6 Heat treatment 6.1 Spheroidizing treatment The spheroidizing treatment shall be as follows: a) heat at a tem

12、perature of 820 10 C for not less than 6 h; b) cool to 700 C at a rate not greater than 10 C per hour; c) furnace cool to 500 C; d) air cool or furnace cool to room temperature. 6.2 Softening treatment The softening treatment shall consist of heating uniformly at a temperature between 700 C and 750

13、C for not less than 1 h, followed by cooling in air or furnace. 6.3 Final heat treatment 6.3.1 Except as provided in 6.3.2, the final heat treatment shall consist of the following: a) Hardening. Heat uniformly at a temperature between 820 C and 860 C, followed by cooling in oil. b) Tempering. Heat a

14、t a temperature of 165 5 C for 1 h, followed by cooling in air. 6.3.2 Alternatively to 6.3.1, the final heat treatment of parts shall be agreed between the manufacturer and the purchaser. NOTE If an alternative heat treatment is used for parts, it may be necessary to agree alternative mechanical pro

15、perties. 7 Mechanical properties 7.1 Hardening test One test sample, 25 mm in diameter and not less than 100 mm long, from each cast shall be heat treated in accordance with 6.3.1. A longitudinal flat surface suitable for hardness testing shall be prepared on the test sample, not less than 5 % of th

16、e diameter or width being removed during preparation. The hardness of the test sample shall be not less than 770 HV or 62 HRC. 7.2 Hardness test 7.2.1 The hardness of material heat treated in accordance with 6.1 shall be not greater than 207 HB unless the material has been cold worked, in which case

17、 it shall be not greater than 248 HB. 7.2.2 The hardness of parts and test samples heat treated in accordance with 6.3.1 shall be not less than 770 HV or 62 HRC. Designation Form Condition of supply S135B Black bars for machining Spheroidized S135D Bright bars for machining Spheroidized and subseque

18、ntly cold drawn, cold rolled, machined or ground S135A Forging stock and billets and bars for subsequent working Softened S135C Forgings (including rolled rings) SpheroidizedblankBS 2S 135:1977 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national

19、 body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the l

20、atest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of whic

21、h can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and fo

22、reign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI imp

23、lementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic

24、information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discoun

25、ts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www

26、.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and

27、Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of neces

28、sary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.