BS 1892-2 9-1986 Gymnasium equipment - Particular requirements - Specification for weight training equipment《体育器械 第2部分 特殊要求 第9节 举重训练设备规范》.pdf

《BS 1892-2 9-1986 Gymnasium equipment - Particular requirements - Specification for weight training equipment《体育器械 第2部分 特殊要求 第9节 举重训练设备规范》.pdf》由会员分享，可在线阅读，更多相关《BS 1892-2 9-1986 Gymnasium equipment - Particular requirements - Specification for weight training equipment《体育器械 第2部分 特殊要求 第9节 举重训练设备规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 1892-2.9: 1986 Gymnasium equipment Part 2: Particular requirements Section 2.9 Specification for weight training equipment UDC 685.641.5:796.88.015.52BS1892-2.9:1986 This British Standard, having been prepared under the directionof the Textiles and Clothing Standards Committee, w

2、as published under the authorityof the Board of BSI and comes into effect on 28 February 1986 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference TCM/14 Draft for comment 84/38860 DC ISBN 0 580 14508 5 Committees responsible for this British Standard The

3、 preparation of this British Standard was entrusted by the Textiles and Clothing Standards Committee (TCM/-) to Technical Committee TCM/14 upon which the following bodies were represented: Birmingham City British Amateur Athletic Board British Amateur Weight Lifters Association British Association o

4、f Advisers and Lecturers in Physical Education British Leather Federation British Sports and Allied Industries Federation Central Council of Physical Recreation City of Glasgow Department of Education and Science Department of the Environment (Building Research Establishment, Princes Risborough Labo

5、ratory) English Basketball Association Greater London Council Gymnasium Equipment Manufacturers Association Home Office Institute of Purchasing and Supply Ministry of Defence Physical Education Association of Great Britain and Northern Ireland Sports Council Timber Research and Development Associati

6、on Amendments issued since publication Amd. No. Date of issue CommentsBS1892-2.9:1986 BSI 09-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 General requirements 1 3 Bars 1 4 Sleeves and grips 1 5 Retaining collars 1 6 Weight discs 1 7 Benches 2 8 Information t

7、o be supplied by the manufacturer 4 9 Marking 5 Figure 1 Knurling for sleeves 1 220 mm in length2 Figure 2 Dimensions of pressing bench3 Figure 3 Barbell position in stability test for benches 4 Figure 4 Barbell position in strength test for benches 5 Table 1 Minimum dimensions of sleeves or grips 1

8、 Table 2 Weight discs 2 Publications referred to Inside back coverBS1892-2.9:1986 ii BSI 09-1999 Foreword This Section of BS 1892 has been prepared under the direction of the Textiles and Clothing Standards Committee and is a revision of clause 4 in BS1892-2.6:1972. Clause 4 is being deleted from th

9、e revision of BS1892-2.6:1972. This Section of BS 1892 applies to equipment for weight training or fitness training. Equipment for competition is not included and is subject to a specification laid down by the International Weight-Lifters Federation. The main change to this revision has been the inc

10、lusion of benches for use with weight training equipment together with stability and strength tests for benches. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Brit

11、ish Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments i

12、ncorporated. This will be indicated in the amendment table on the inside front cover.BS1892-2.9:1986 BSI 09-1999 1 1 Scope This Section of BS 1892 specifies requirements for equipment used for weight training or fitness training. This standard does not apply to equipment for competition use. The req

13、uirements for benches in clause 7 also apply to abdominal boards and incline or recline benches. NOTEThe titles of the publications referred to in this standard are listed on the inside back cover. 2 General requirements Weight training equipment shall comply with the requirements of BS 1892-1 excep

14、t in so far as they are modified by this Section. 3 Bars 3.1 Dimensions Bars for use with dumbells and barbells shall be manufactured in nominal lengths of300,380,450,1 370,1 520 or1 830 mm and shall have nominal diameters of either 25mm or 28mm. 3.2 Material Bars shall be manufactured from solid br

15、ight bar complying with BS 970. 3.3 Finish The ends of the bars shall be either deburred or radiused to a minimum radius of 3mm to remove sharp corners. NOTEThe bars may also be plated. Any finishing process shall not affect the strength of the bars. 4 Sleeves and grips 4.1 Sleeves Sleeves shall be

16、supplied in the following minimum lengths: a) 800mm for bars 1 370mm in length; b) 1 070mm for bars 1 520mm in length; c) 1 220mm for bars 1 830mm in length. Sleeves 1 220 mm in length shall be knurled in three places as shown in Figure 1. NOTEOther sleeves may also be knurled. 4.2 Grips A cast grip

17、 made from material complying with grade 220 of BS1452 shall be provided and shall comply with the minimum dimensions given in Table 1. The central grip shall have either a knurled or serrated finish and shall be either deburred or radiused to a minimum radius of 3mm to remove sharp corners. Table 1

18、 Minimum dimensions of sleeves or grips 5 Retaining collars 5.1 General Barbells shall be supplied with both inside and outside collars. Dumbells shall be supplied with outside collars. In all cases the method of securing the collars shall meet the performance requirements specified in 5.4. 5.2 Fixe

19、d collars If dumbell and barbell sets are supplied with collars that are permanently fixed, the fixing shall be by welding or by the fitting of steel dowel pins so that the weight discs cannot be removed. NOTEDumbells and barbells with fixed collars improve safety and reduce the risk of weight discs

20、 being lost or stolen. 5.3 Screws A spanner or wrench shall be supplied for tightening. 5.4 Performance requirement When a mass of 10kg is dropped over a vertical distance of 300mm onto the collar, the collar shall suffer no damage, e.g. breakage or pieces split off. 6 Weight discs 6.1 Materials Wei

21、ght discs shall be manufactured from cast iron complying with grade 220 of BS1452. 6.2 Dimensions Weight discs shall have a hole of nominal diameter 26mm in the centre for use with bars of 25mm diameter, and shall have a hole of nominal diameter 29mm for use with bars of 28mm diameter. The weight di

22、scs shall be made to the nominal sizes given in Table 2. 6.3 Manufacture Weight discs shall be manufactured to the following requirements. a) There shall be a recess between the boss and the rim. Component part Minimum dimension Overall length of sleeve or grip (including end flanges) Length of slee

23、ve or grip Diameter of sleeve or grip Diameter of end flanges of sleeve or grip mm 132 110 38 64BS1892-2.9:1986 2 BSI 09-1999 b) The holes in the weight discs shall have parallel sides so that the discs fit evenly on the bar. c) The centre boss and the rim shall be of equal thickness. d) The edges o

24、f the weight discs shall be deburred or radiused to a minimum radius of 3mm to remove sharp corners. e) The largest weight disc of a set shall be on the inside with the smaller weight discs graduating to the outside. f) If weight discs have a colour coding it shall be as given in Table 2. Table 2 We

25、ight discs g) If weight discs are supplied with a rubber tyre or covered with rubber then for the 20kg disc any rubber tyre or rubber covering shall not increase the diameter specified in Table 2. 7 Benches 7.1 Dimensions The dimensions of benches shall be as shown in Figure 2. 7.2 Materials If the

26、bench is of bolted design the joints shall use either high tensile steel bolts complying with grade 8.8 of BS 3692 or screws with self-locking nuts made from high tensile steel complying with grade 8 ofBS 3692, with nylon inserts. The board forming the top of the bench shall be constructed from lami

27、nated plywood having a minimum thickness of 12mm. The board shall be fixed to the frame by means of machine screws or bolts into metal inserts in the board. Woodscrews or self-tapping screws shall not be used. 7.3 Construction The weight stands shall rest on the floor. The stands shall be either adj

28、ustable or have one or more storage points (see Figure 3 for minimum height). The locating pins shall be fitted with a locking device. If the bench is constructed with the weight supports less than 1 000mm apart, it shall be widened at floor level in order that the requirement of 7.4 is met. Benches

29、 shall be padded with a foam having a minimum thickness of 25mm and a minimum density of 3.63kg/m 3 . The foam shall be covered. NOTEA spotting platform may be provided behind the weight stands. Mass Diameter Width of rim Colour code kg mm mm 0.50 ( 3 %) 1.25 ( 3 %) 2.50 ( 3 %) 5.00 ( 3 %) 7.50 ( 3

30、%) 10.00 ( 3 %) 12.50 ( 3 %) 15.00 ( 3 %) 20.00 ( 3 %) 127 165 203 235 280 330 382 450 18.5 22.0 26.5 28.0 29.0 27.0 25.0 32.0 Pale blue Red Green Black Purple or DarkBlue Yellow Figure 1 Knurling for sleeves1 220mm in lengthBS1892-2.9:1986 BSI 09-1999 3 Figure 2 Dimensions of pressing benchBS1892-2

31、.9:1986 4 BSI 09-1999 7.4 Performance requirements Benches shall comply with the following performance requirements. a) When a load of 440kg is applied, midway along the length of a horizontally placed bench, there shall be no permanent distortion to the bench. NOTEThe test can be conveniently carri

32、ed out by placing a short barbell carrying weight discs at each end as shown in Figure 4. Precautions should be taken to ensure that the barbell does not roll along the bench. b) When a 1 370mm long barbell is loaded with weight discs to a total mass of 110kg and clamped in its maximum out of centre

33、 position over the bench, as shown in Figure 3, then the bench shall not overturn. c) When a barbell of total mass 200kg is dropped over a distance of 150mm with the adjustable stand set in its highest position there shall be no failure, e.g. breakage of locking pins. NOTEThe above requirements also

34、 apply to abdominal boards and incline or recline benches. 8 Information to be supplied by the manufacturer The manufacturer shall supply the following information with weight training equipment: a) for bars, sleeves and grips the full specification of the materials used; b) for collars, the full sp

35、ecification of the materials used and the type of screws provided; c) assembly instructions for benches, if supplied in kit form; d) information on care and maintenance. Figure 3 Barbell position in stability test for benchesBS1892-2.9:1986 BSI 09-1999 5 9 Marking All items of weight training equipm

36、ent shall be marked with the following information: a) the manufacturers name, trademark or other means of identification; b) the number and date of this British Standard, i.e. BS 1892-2.9:1986 1) ; c) for weight discs, the mass in kilograms. 1) Marking BS 1892-2.9:1986 on or in relation to a produc

37、t is a claim by the manufacturer that the product has been manufactured to the requirements of the standard. The accuracy of such a claim is therefore solely the manufacturers responsibility. Enquiries as to the availability of third party certification to support such claims should be addressed to

38、the Director, Quality Assurance Division, BSI, PO Box 357, Milton Keynes MK 14 6LO for certification marks administered by BSI or to the appropriate authority for other certification marks. Figure 4 Barbell position in strength test for benches6 blankBS1892-2.9:1986 BSI 09-1999 Publications referred

39、 to BS 970, Specification for wrought steels for mechanical and allied engineering purposes. BS 1452, Specification for grey iron castings. BS 1892, Gymnasium equipment. BS 1892-1, General requirements. BS 1892-2, Section 2.6 Boxing rings and weight training equipment 2) . BS 3692, ISO metric precis

40、ion hexagon bolts, screws and nuts. 2) Referred to in the foreword only.BS1892-2.9: 1986 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the

41、international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services

42、. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual upd

43、ating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for

44、 international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and i

45、ts Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and

46、 receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the in

47、ternational standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.

48、This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.