ASTM D7467-2013 red 0625 Standard Specification for Diesel Fuel Oil Biodiesel Blend (B6 to B20)《柴油 生物柴油混合物 (B6至B20) 的标准规范》.pdf

《ASTM D7467-2013 red 0625 Standard Specification for Diesel Fuel Oil Biodiesel Blend (B6 to B20)《柴油 生物柴油混合物 (B6至B20) 的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7467-2013 red 0625 Standard Specification for Diesel Fuel Oil Biodiesel Blend (B6 to B20)《柴油 生物柴油混合物 (B6至B20) 的标准规范》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7467 10D7467 13Standard Specification forDiesel Fuel Oil, Biodiesel Blend (B6 to B20)1This standard is issued under the fixed designation D7467; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisio

2、n. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers fuel blend grades of 6 to 20 volume percent (%) biodiesel with the remainder being a light middleor mid

3、dle distillate diesel fuel, collectively designated as B6 to B20. These grades are suitable for various types of diesel engines.1.1.1 The biodiesel component of the blend shall conform to the requirements of Specification D6751.The remainder of the fuelshall be a light middle or middle distillate gr

4、ade diesel fuel conforming to Specification D975 grades No. 1-D and No. 2-D of anysulfur level specified with the following exceptions. The light middle or middle distillate grade diesel fuel whose sulfur level,aromatic level, cetane, or lubricity falls outside of Specification D975 may be blended w

5、ith biodiesel meeting Specification D6751,provided the finished mixtures meets this specification.1.1.2 The fuel sulfur grades are described as follows:1.1.2.1 Grade B6 to B20 S15A fuel with a maximum of 15 ppm sulfur.1.1.2.2 Grade B6 to B20 S500A fuel with a maximum of 500 ppm sulfur.1.1.2.3 Grade

6、B6 to B20 S5000A fuel with a maximum of 5000 ppm sulfur.1.2 This specification prescribes the required properties of B6 to B20 biodiesel blends at the time and place of delivery. Thespecification requirements may be applied at other points in the production and distribution system when provided by a

7、greementbetween the purchaser and the supplier.1.2.1 Nothing in this specification shall preclude observance of federal, state, or local regulations that may be more restrictive.NOTE 1The generation and dissipation of static electricity can create problems in the handling of distillate diesel fuel o

8、ils. For more information onthis subject, see Guide D4865.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.2. Referenced Documents2.1 ASTM Standards:2D56 Test Method for Flash Point by Tag Closed Cup TesterD86 Test Method f

9、or Distillation of Petroleum Products at Atmospheric PressureD93 Test Methods for Flash Point by Pensky-Martens Closed Cup TesterD129 Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method)D130 Test Method for Corrosiveness to Copper from Petroleum Products b

10、y Copper Strip TestD445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)D482 Test Method for Ash from Petroleum ProductsD524 Test Method for Ramsbottom Carbon Residue of Petroleum ProductsD613 Test Method for Cetane Number of Diesel Fuel Oi

11、lD664 Test Method for Acid Number of Petroleum Products by Potentiometric TitrationD975 Specification for Diesel Fuel OilsD976 Test Method for Calculated Cetane Index of Distillate FuelsD1266 Test Method for Sulfur in Petroleum Products (Lamp Method)D1319 Test Method for Hydrocarbon Types in Liquid

12、Petroleum Products by Fluorescent Indicator AdsorptionD1552 Test Method for Sulfur in Petroleum Products (High-Temperature Method)1 This specification is under the jurisdiction of ASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.E0 onBurner

13、, Diesel, Non-Aviation Gas Turbine, and Marine Fuels.Current edition approved Aug. 1, 2010May 1, 2013. Published October 2010May 2013. Originally approved in 2008. Last previous edition approved in 20092010 asD7467D7467 10.09a. DOI: 10.1520/D7467-10.10.1520/D7467-13.2 For referencedASTM standards, v

14、isit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM stan

15、dard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by AST

16、M is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D2500 Test Method for Cloud Point of Petroleum ProductsD2622 Test Method for

17、Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence SpectrometryD2709 Test Method for Water and Sediment in Middle Distillate Fuels by CentrifugeD2880 Specification for Gas Turbine Fuel OilsD3117 Test Method for Wax Appearance Point of Distillate Fuels (Withdrawn 2010)3D3120 Tes

18、t Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative MicrocoulometryD3828 Test Methods for Flash Point by Small Scale Closed Cup TesterD4057 Practice for Manual Sampling of Petroleum and Petroleum ProductsD4294 Test Method for Sulfur in Petroleum and Petroleum

19、Products by Energy Dispersive X-ray Fluorescence SpectrometryD4539 Test Method for Filterability of Diesel Fuels by Low-Temperature Flow Test (LTFT)D4737 Test Method for Calculated Cetane Index by Four Variable EquationD4865 Guide for Generation and Dissipation of Static Electricity in Petroleum Fue

20、l SystemsD5453 Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel,and Engine Oil by Ultraviolet FluorescenceD5771 Test Method for Cloud Point of Petroleum Products (Optical Detection Stepped Cooling Method)D5772 Test Method for Cloud P

21、oint of Petroleum Products (Linear Cooling Rate Method)D5773 Test Method for Cloud Point of Petroleum Products (Constant Cooling Rate Method)D6079 Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR)D6217 Test Method for Particulate Contamination in Mid

22、dle Distillate Fuels by Laboratory FiltrationD6371 Test Method for Cold Filter Plugging Point of Diesel and Heating FuelsD6468 Test Method for High Temperature Stability of Middle Distillate FuelsD6469 Guide for Microbial Contamination in Fuels and Fuel SystemsD6751 Specification for Biodiesel Fuel

23、Blend Stock (B100) for Middle Distillate FuelsD6890 Test Method for Determination of Ignition Delay and Derived Cetane Number (DCN) of Diesel Fuel Oils by Combustionin a Constant Volume ChamberD7220 Test Method for Sulfur inAutomotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray

24、FluorescenceSpectrometryD7371 Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil Using Mid InfraredSpectroscopy (FTIR-ATR-PLS Method)D7397 Test Method for Cloud Point of Petroleum Products (Miniaturized Optical Method)E29 Practice for Using Significant D

25、igits in Test Data to Determine Conformance with Specifications2.2 Other Standards:26 CFR Part 48 Manufacturers and Retailers Excise Taxes440 CFR Part 80 Regulation of Fuels and Fuel Additives4EN 14078 Liquid petroleum products - Determination of fatty acid methyl ester (FAME) content in middle dist

26、illates - Infraredspectrometry method5EN 14112 Fat and oil derivatives - Fatty acid methyl esters (FAME) - Determination of oxidation stability (Acceleratedoxidation test)5EN 15751 Automotive fuels - Fatty acid methyl ester (FAME) fuel and blends with diesel fuel - Determination of oxidationstabilit

27、y by accelerated oxidation method53. Terminology3.13.2 biodiesel, nfuel comprised of mono-alkyl esters of long chain fatty acids derived from vegetable oils or animal fats,designated B100.3.3 B6 to B20, nfuel blend consisting of 6 to 20 volume percent biodiesel conforming to the requirements of Spec

28、ificationD6751 with the remainder being a light middle or middle distillate grade diesel fuel and meeting the requirements of thisspecification.3.3.1 DiscussionThe abbreviation BXX represents a specific blend concentration in the range B6 to B20, where XX is the percent volume ofbiodiesel in the fue

29、l blend.3 The last approved version of this historical standard is referenced on www.astm.org.4 Available from U.S. Government Printing Office Superintendent of Documents, 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.5 Available from the National CEN members listed on the CEN website

30、 (www.cenorm.be.) or from the CEN/TC 19 Secretariat (astmnen.nl).D7467 1323.4 S(numerical specification maximum)indicates the maximum sulfur content, in weight ppm (g/g), allowed by thisspecification.4. Test Methods4.1 The requirements enumerated in this specification shall be determined in accordan

31、ce with the following methods:4.1.1 Acid NumberTest Method D664.4.1.2 Flash PointTest Method D93, except where other methods are prescribed by law. Test Method D3828 may be used asan alternate with the same limits. Test Method D56 may be used as an alternate with the same limits, provided the flash

32、point isbelow 93C. This test method will give slightly lower values. In cases of dispute, Test Method D93 shall be used as the refereemethod.4.1.3 Cloud PointTest Method D2500. For all B6 to B20 grades in Table 1, Test Method D7397 and the automatic TestMethods D5771, D5772, or D5773 may be used as

33、alternates with the same limits. Test Method D3117 may also be used sinceit is closely related to Test Method D2500. In case of dispute, Test Method D2500 shall be the referee test method.4.1.4 Cold Filter Plugging Point (CFPP)Test Method D6371.TABLE 1 Detailed Requirements for B6 to B20 Biodiesel B

34、lendsProperty Test Method GradeB6 to B20 S15 B6 to B20 S500A B6 to B20 S5000BAcid Number, mg KOH/g, max D664 0.3 0.3 0.3Viscosity, mm2/s at 40C D445 1.9-4.1C 1.9-4.1C 1.9- 4.1CFlash Point, C, min D93 52D 52D 52DCloud Point, C, max or LTFT/CFPP, C, maxD2500, D4539, D6371 E E ESulfur Content, (g/g) D5

35、453 15 . .mass %, max D2622 . 0.05 .mass %, max D129 . . 0.50Distillation Temperature, C,90% vol recovered, maxD86 343 343 343Ramsbottom Carbon Residueon 10% bottoms, mass %, maxD524 0.35 0.35 0.35Cetane Number, min D613F 40G 40G 40GOne of the following must bemet:(1) Cetane index, min.D976-80H 40 4

36、0 40(2) Aromaticity, %vol, max D1319-03H 35 35 .Ash Content, mass%, max D482 0.01 0.01 0.01Water and Sediment, volume%,maxD2709 0.05 0.05 0.05Copper Corrosion, 3 h at 50C,maxD130 No. 3 No. 3 No. 3Biodiesel Content, % (V/V) D7371 6. - 20. 6. - 20. 6. - 20.Oxidation Stability, hours, min EN 15751 6 6

37、6Lubricity, HFRR at 60C, mi-cron (m), maxD6079 520I 520I 520IA Under United States of America regulations, if Grades B6-20 S500 are sold for tax exempt purposes then, at, or beyond terminal storage tanks, they are required by 26CFR Part 48 to contain the dye Solvent Red 164 at a concentration spectr

38、ally equivalent to 3.9 lb per thousand barrels of the solid dye standard Solvent Red 164, or thetax must be collected.B Under United States of America regulations, Grades B6-20 S5000 are required by 40 CFR part 80 to contain a sufficient amount of the dye Solvent Red 164 so itspresence is visually a

39、pparent. At or beyond terminal storage tanks, they are required by 26 CFR Part 48 to contain the dye Solvent Red 164 at a concentration spectrallyequivalent to 3.9 lb per thousand barrels of the solid dye standard Solvent Red 26.C If Grade No. 1-D or blends of Grade No. 1-D and Grade No. 2-D diesel

40、fuel are used, the minimum viscosity shall be 1.3 mm2/s.D If Grade No. 1-D or blends of Grade No. 1-D and Grade No. 2-D diesel fuel are used, or a cloud point of less than -12C is specified, the minimum flash point shall be38C.E It is unrealistic to specify low temperature properties that will ensur

41、e satisfactory operation at all ambient conditions. In general, cloud point (or wax appearance point)Low Temperature Flow Test, and Cold Filter Plugging Point Test may be useful to estimate vehicle low temperature operability limits but their use with B6 to B20 has notbeen validated. However, satisf

42、actory operation below the cloud point (or wax appearance point) may be achieved depending on equipment design, operating conditions,and the use of flow-improver additives as described in X3.1.2. Appropriate low temperature operability properties should be agreed upon between the fuel supplier andpu

43、rchaser for the intended use and expected ambient temperatures. Test Methods D4539 and D6371 may be especially useful to estimate vehicle low temperatureoperability limits when flow improvers are used but their use with B6 to B20 from a full range of biodiesel feedstock sources has not been validate

44、d. Due to fuel deliverysystem, engine design, and test method differences, low temperature operability tests may not provide the same degree of protection in various vehicle operating classes.Tenth percentile minimum air temperatures for U.S. locations are provided in Appendix X3 as a means of estim

45、ating expected regional temperatures. The tenth percentileminimum air temperatures may be used to estimate expected regional target temperatures for use withTest Methods D2500, D4539, and D6371. Refer to X3.1.3 for furthergeneral guidance on test application.F Calculated cetane index approximation,

46、Test Method D4737, is not applicable to biodiesel blends.G Low ambient temperatures, as well as engine operation at high altitudes, may require the use of fuels with higher cetane ratings. If the diesel fuel is qualified underTable 1of Specification D975 for cetane, it is not necessary to measure th

47、e cetane number of the blend. This is because the cetane number of the individual blend componentswill be at least 40, so the resulting blend will also be at least 40 cetane number.H These test methods are specified in 40 CFR Part 80.I If the diesel fuel is qualified under Table 1 of Specification D

48、975 for lubricity, it is not necessary to measure the lubricity of the blend. This is because the lubricity of theindividual blend components will be less than 520 micron (m) so the resulting blend will also be less than 520 (m).J Other sulfur limits can apply in selected areas in the United States

49、and in other countries.D7467 1334.1.5 Low Temperature Flow Test (LTFT)Test Method D4539.4.1.6 Water and SedimentTest Method D2709.4.1.7 Carbon ResidueTest Method D524.4.1.8 AshTest Method D482.4.1.9 DistillationTest Method D86.4.1.10 ViscosityTest Method D445.4.1.11 SulfurTable 2 shows the referee test methods and alternate test methods for sulfur, the range over which each testmethod applies and the corresponding fuel grades.4.1.12 AromaticityTest Method D1319.This test method provides an indication of the aromatic content of fuels. For fuel