ASTM D5456-2007 Standard Specification for Evaluation of Structural Composite Lumber Products《结构复合木制品评定的标准规范》.pdf

《ASTM D5456-2007 Standard Specification for Evaluation of Structural Composite Lumber Products《结构复合木制品评定的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5456-2007 Standard Specification for Evaluation of Structural Composite Lumber Products《结构复合木制品评定的标准规范》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 5456 07Standard Specification forEvaluation of Structural Composite Lumber Products1This standard is issued under the fixed designation D 5456; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisio

2、n. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.INTRODUCTIONStructural composite lumber is intended for use as an engineering material for a variety of end-useapplications. The composition

3、of the lumber varies by wood species, adhesive composition, woodelement size, shape, and arrangement. To provide the intended performance, composite lumberproducts require: (1) an evaluation of the mechanical and physical properties and their response toend-use environments, and (2) establishment of

4、 and conformance to standard performance specifica-tions for quality.Procedures contained in this specification are also to be used for establishing the design propertiesand for checking the effectiveness of property assignment and quality assurance procedures.The quality assurance sections in this

5、specification are intended to serve as a basis for designingquality-control programs specific to each product. The objective is to ensure that design valuesestablished in the qualification process are maintained.This specification is arranged as follows:SectionQualification 6Determination of Allowab

6、le Design Stresses 7Independent Inspection 8Quality Assurance 101. Scope1.1 This specification recognizes the complexity of struc-tural glued products. Consequently, this specification coversboth specific procedures and statements of intent that samplingand analysis must relate to the specific produ

7、ct.1.2 This specification was developed in the light of cur-rently manufactured products as defined in 3.2. Materials thatdo not conform to the definitions are beyond the scope of thisspecification. A brief discussion is found in Appendix X1.1.3 Details of manufacturing procedures are beyond thescop

8、e of this specification.NOTE 1There is some potential for manufacturing variables to affectthe properties of members that are loaded for sustained periods of time.Users of this specification are advised to consider the commentary on thistopic in Appendix X1.1.4 This specification primarily considers

9、 end use in dryservice conditions, such as with most protected framing mem-bers, where the average equilibrium moisture content forsolid-sawn lumber is less than 16 %. The conditioning envi-ronment of 6.3 is considered representative of such uses.1.5 The performance of structural composite lumber is

10、affected by wood species, wood element size and shape, andadhesive and production parameters. Therefore, products pro-duced by each individual manufacturer shall be evaluated todetermine their product properties, regardless of the similarityin characteristics to products produced by other manufactur

11、ers.Where a manufacturer produces product in more than onefacility, each production facility shall be evaluated indepen-dently. For additional production facilities, any revisions to thefull qualification program in accordance with this specificationshall be approved by the independent qualifying ag

12、ency.1.6 This specification is intended to provide manufacturers,regulatory agencies, and end users with a means to evaluate acomposite lumber product intended for use as a structuralmaterial.1.7 This specification covers initial qualification sampling,mechanical and physical tests, analysis, and de

13、sign valueassignments. Requirements for a quality-control program andcumulative evaluations are included to ensure maintenance ofallowable design values for the product.1This specification is under the jurisdiction of ASTM Committee D07 on Woodand is the direct responsibility of Subcommittee D07.02

14、on Lumber and EngineeredWood Products.Current edition approved July 15, 2007. Published August 2007. Originallyapproved in 1993. Last previous edition approved in 2005 as D 5456 05a.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.1.8

15、 This specification, or parts thereof, shall be applicable tostructural composite lumber portions of manufactured struc-tural components.1.9 The values stated in inch-pound units are to be regardedas the standard. The SI units given in parentheses are forinformation only.1.10 This standard does not

16、purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:

17、2C 177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarded-Hot-Plate ApparatusC 355 Test Methods for Water Vapor Transmission of ThickMaterials3C 384 Test Method for Impedance and Absorption ofAcoustical Materials by Impedance Tube MethodC

18、423 Test Method for Sound Absorption and Sound Ab-sorption Coefficients by the Reverberation Room MethodD9 Terminology Relating to Wood and Wood-Based Prod-uctsD 143 Test Methods for Small Clear Specimens of TimberD 150 Test Methods for AC Loss Characteristics and Per-mittivity (Dielectric Constant)

19、 of Solid Electrical Insula-tionD 198 Test Methods of Static Tests of Lumber in StructuralSizesD 245 Practice for Establishing Structural Grades and Re-lated Allowable Properties for Visually Graded LumberD 669 Test Method for Dissipation Factor and PermittivityParallel with Laminations of Laminated

20、 Sheet and PlateMaterialsD 905 Test Method for Strength Properties of AdhesiveBonds in Shear by Compression LoadingD 1037 Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel MaterialsD 1666 Test Methods for Conducting Machining Tests ofWood and Wood-Base MaterialsD 1761 Test

21、 Methods for Mechanical Fasteners in WoodD 2132 Test Method for Dust-and-Fog Tracking and Ero-sion Resistance of Electrical Insulating MaterialsD 2394 Test Methods for Simulated Service Testing ofWood and Wood-Base Finish FlooringD 2395 Test Methods for Specific Gravity of Wood andWood-Based Materia

22、lsD 2559 Specification for Adhesives for Structural Lami-nated Wood Products for Use Under Exterior (Wet Use)Exposure ConditionsD 2718 Test Methods for Structural Panels in Planar Shear(Rolling Shear)D 2915 Practice for Evaluating Allowable Properties forGrades of Structural LumberD 3201 Test Method

23、 for Hygroscopic Properties of Fire-Retardant Wood and Wood-Based ProductsD 3755 Test Method for Dielectric Breakdown Voltage andDielectric Strength of Solid Electrical Insulating MaterialsUnder Direct-Voltage StressD 4442 Test Methods for Direct Moisture Content Measure-ment of Wood and Wood-Base M

24、aterialsD 4761 Test Methods for Mechanical Properties of Lumberand Wood-Base Structural MaterialD 4933 Guide for Moisture Conditioning of Wood andWood-Based MaterialsD 5055 Specification for Establishing and MonitoringStructural Capacities of Prefabricated Wood I-JoistsD 5457 Specification for Compu

25、ting Reference Resistanceof Wood-Based Materials and Structural Connections forLoad and Resistance Factor DesignD 5764 Test Method for Evaluating Dowel-BearingStrength of Wood and Wood-Based ProductsD 6815 Specification for Evaluation of Duration of Loadand Creep Effects of Wood and Wood-Based Produ

26、ctsE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE119 Test Methods for Fire Tests of Building Constructionand Materials2.2 Canadian Standards:4CSA Standards for Wood Adhesives, O112 Series3. Terminology3.1 DefinitionsStandard definitions of wood terms aregiven in Terminolog

27、y D9.3.2 Definitions of Terms Specific to This Standard:3.2.1 Exposure 1 durabilitya bond classification forwood-based products that are not permanently exposed to theweather. Wood-based products classified as Exposure 1 areintended to resist the effects of moisture on structural perfor-mance due to

28、 construction delays or other conditions of similarseverity.3.2.2 structural composite lumberin this specification,structural composite lumber (SCL) is any of laminated veneerlumber (LVL), parallel strand lumber (PSL), laminated strandlumber (LSL), or oriented strand lumber (OSL). These mate-rials a

29、re intended for structural use and they shall be bondedwith an exterior adhesive.3.2.2.1 laminated strand lumbera composite of woodstrand elements with wood fibers primarily oriented along thelength of the member. The least dimension of the strands shallnot exceed 0.10 in. (2.54 mm) and the average

30、length shall bea minimum of 150 times the least dimension.3.2.2.2 laminated veneer lumbera composite of woodveneer sheet elements with wood fibers primarily oriented2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Bo

31、ok of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from Canadian Standards Association (CSA), 178 Rexdale Blvd.,Toronto, ON Canada M9W1R3.D5456072along the length of the member. Veneer thickness shall notexceed 0.25 in. (6.4

32、mm).3.2.2.3 oriented strand lumbera composite of woodstrand elements with wood fibers primarily oriented along thelength of the member. The least dimension of the strands shallnot exceed 0.10 in. (2.54 mm) and the average length shall bea minimum of 75 times the least dimension.3.2.2.4 parallel stra

33、nd lumbera composite of wood ve-neer strand elements with wood fibers primarily oriented alongthe length of the member. The least dimension of strands shallnot exceed 0.25 in. (6.4 mm) and the average length shall be aminimum of 300 times the least dimension.3.2.3 DiscussionSCL has three mutually pe

34、rpendiculardirections of orientation (see Fig. 1):L DirectionParallel to the longitudinal direction of the member.X DirectionParallel to a surface of the member and normal to the L direction.Y DirectionNormal to both L and X direction.In this specification, longitudinal shear means shear stress inth

35、e L-X and L-Y planes. Planar shear is stress in the X-Y plane.4. Materials4.1 Wood ElementsWood elements used in the fabricationof SCL products shall conform to 3.2.4.2 AdhesivesAdhesives used in the fabrication of SCLproducts shall conform to the requirements in SpecificationD 2559. Alternatively,

36、the durability of high temperature cur-ing adhesives can be evaluated with the procedures specified inAnnex A4.2 (see Note 2). For this procedure, the averagestrength retention shall be at least 50%. In Canada, adhesivesshall conform to the appropriate section of CSAO112 Series Mstandards for wood a

37、dhesives.NOTE 2Adhesives evaluated by Annex A4.2 are only qualified forExposure 1 conditions; other conditions are beyond the scope of thisspecification. See the commentary and the section on Design andMechanical Property Concerns in Appendix X1 for further information.5. Mechanical Properties5.1 Th

38、e characteristic value for SCL is a statistic derivedfrom test data as specified in 7.1. For bending and tensionparallel to grain, the characteristic value is obtained at the unitvolume as specified in 6.5.1 and 6.5.2.5.2 The design stress related to SCL is derived from thecharacteristic value throu

39、gh application of the adjustmentslisted in Table 1 of this specification.5.3 The allowable design stress published for engineeringuse shall be derived from the design stress modified by factorsgiven in 7.3.6. Qualification6.1 Samples for qualification testing shall be representativeof the population

40、 being evaluated. When an intentional modi-fication to the process results in a reduction in mechanicalproperties as indicated by the quality-control program, thennew qualification is required.6.1.1 Qualification tests shall be conducted or witnessed bya qualified agency in accordance with 8.1.All t

41、est results are tobe certified by the qualified agency.6.2 Sampling of the test material shall be done in accor-dance with applicable portions of Section 3, “Statistical Meth-odology,” of Practice D 2915.6.2.1 Design stress, except for compression perpendicular tograin and apparent modulus of elasti

42、city, shall be based on thefifth percentile tolerance limit.6.2.2 The confidence level for calculating tolerance limitsand confidence intervals shall be 75 %.6.2.3 Minimum sample size for calculating tolerance limitson fifth percentiles shall be 53. When volume effect tests aremade at multiple sizes

43、 for bending and tension, the minimumsample shall be 78 specimens at the unit volume specimen size.6.2.3.1 The calculated fifth percentile parametric tolerancelimits (PTL) shall have a standard error no greater than 5 % ofthe PTL, when evaluated in accordance with 3.4.3.2 of PracticeD 2915. When nec

44、essary the sample shall be increased beyondthe minimum of 53, to meet this requirement.6.2.4 Minimum unit sample sizes for compression perpen-dicular to grain (see 6.5.4) shall provide estimation of meanvalues within 5 % in accordance with 3.4.2 of Practice D 2915.Minimum sample size shall not be le

45、ss than 30.6.3 Composite lumber used in qualification testing shall bebrought to moisture equilibrium in a conditioned environmentof 20 6 6C (68 6 11F) and 65 % (65 %) relative humidity.Methods for determination of completion of conditioning aregiven in Guide D 4933.6.4 Moisture content and specific

46、 gravity shall be measuredand reported for each specimen tested in the qualificationFIG. 1 Orientations for Structural Composite LumberTABLE 1 Adjustment FactorsNOTEApparent modulus of elasticity is computed from a deformation,and compression strength perpendicular to grain is established at adeform

47、ation limit. Neither is subject to load duration adjustments. Allother factors are the product of 1.62, that adjusts data to normal durationas defined in 7.3.1 of Practice D 245, and an additional factor foruncertainty (see Appendix X3 for an explanation of the shear block testadjustment factor).Pro

48、perty Adjustment FactorApparent modulus of elasticity 1.00Bending strength 2.10Tensile strength parallel to grain 2.10Compressive strength parallel to grain 1.90Longitudinal shear strengthShear block test 3.15Structural-size shear test 2.10Compressive strength perpendicular to grain 1.67D5456073prog

49、ram. Measurement for moisture content shall be in accor-dance with Test Methods D 4442 and measurement of specificgravity shall be in accordance with Test Methods D 2395.6.5 Mechanical PropertiesThe properties that shall beevaluated by qualification testing shall include, but are notlimited to: bending strength and stiffness, tensile strengthparallel to the grain, compressive strength parallel to the grain,compressive strength perpendicular to the grain, and longitu-dinal shear strength.6.5.1 BendingModulus of rupture and apparent modulusof elasticity shall be det