ASTM D2563-2008(2015) Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic Laminate Parts《玻璃纤维增强塑料层压零件中可见缺陷分类的标准实施规程》.pdf

《ASTM D2563-2008(2015) Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic Laminate Parts《玻璃纤维增强塑料层压零件中可见缺陷分类的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D2563-2008(2015) Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic Laminate Parts《玻璃纤维增强塑料层压零件中可见缺陷分类的标准实施规程》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D2563 08 (Reapproved 2015)Standard Practice forClassifying Visual Defects in Glass-Reinforced PlasticLaminate Parts1This standard is issued under the fixed designation D2563; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis

2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This practice c

3、overs acceptance criteria for visual in-spection of parts made from molded glass-reinforced plasticlaminates.1.2 This practice presents word descriptions of possibledefects to serve as a guide for contracts, drawings, productspecifications, and final inspection.1.3 This practice also categorizes dif

4、ferent inspection re-quirements for levels of product quality.1.4 The allowable size and frequency of permitted defectswithin the acceptance level categories of this specification aregeneral and not related to specific service requirements. ALevel IV of allowable defects which defines allowable size

5、,frequency, and permitted repair procedures should be estab-lished for specific service requirements as agreed upon be-tween the purchaser and the supplier.1.5 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.6 This standard d

6、oes not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE 1There is no known ISO equiva

7、lent to this standard.2. Acceptance Criteria2.1 The method and frequency of sampling and the allow-able defects may be previously agreed upon between thepurchaser and the seller.2.2 Dimensions and TolerancesParts shall be inspectedfor conformance with dimensions and tolerances specified onthe drawin

8、gs. Any dimensions falling outside the specifiedlimits shall be cause for rejection.2.3 InsertsAll inserts, nuts, studs, and lugs shall not bedamaged in any way, nor coated with laminate materials insuch a way as to impair function or mechanical fit. Threads inmolded-in inserts shall be clean, smoot

9、h, free of nicks, tears, orother damage. There shall be no laminate materials or flash onthe threads. If necessary, threaded inserts may be retapped toclean them or remove flash. Threads containing locking fea-tures or coated for corrosion resistance shall not be retapped.2.4 Molded-In Threads or Co

10、red HolesMolded-in threadsor cored holes shall be free of visible defects such as chips,cracks, shorts, etc. Molded-in threads may be retapped orrepaired unless otherwise specifically noted on the productdrawings.2.5 WorkmanshipWorkmanship shall be in accordancewith good commercial practices as list

11、ed in Table 1 forapplicable acceptance levels.2.6 Critical AreaSome portions of a part may be consid-ered more critical than others. A critical area is here defined asan area in which the presence of imperfections is considered tobe most detrimental. The areas of parts that are criticalstructurally,

12、 aerodynamically, or electrically shall be uniformand free of defects as listed in Table 1, if so stated on theproduct drawing. Critical areas may be designated on theproduct drawing by one of the following methods:2.6.1 Encircle critical areas, or2.6.2 Cross-hatch areas to designate areas of variou

13、s levels,or2.6.3 Word description.2.7 Allowable Defects, VisualThe defects in noncriticalareas which by nature, content, or frequency do not affectserviceability of the part are designated as allowable defects.Allowable defects shall be fully described as to type, size,number, extent allowed, and sp

14、acing. The appropriate accep-tance level (Table 1) for defects in these areas must bespecified. Where Level IV is used the defects must be fullydescribed on the product drawing. Defects greater than thoselisted in the product specifications, drawings, or contracts forthe part shall be cause for reje

15、ction.1This practice is under the jurisdiction ofASTM Committee D20 on Plastics andis the direct responsibility of Subcommittee D20.18 on Reinforced ThermosettingPlastics.Current edition approved Sept. 1, 2015. Published September 2015. Originallyapproved in 1966. Last previous edition approved in 2

16、008 as D2563 - 08. DOI:10.1520/D2563-08R15.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1TABLE 1 Allowable DefectsName DefinitionVisual Acceptance LevelsLevel I Level II Level IIIChip a small piece broken off an edge or surface none

17、 maximum dimension of break, 3.0 mm(18 in.)maximum dimension of break, 6.5 mm(14 in.)Crack an actual separation of the laminate, visible onopposite surfaces, and extending through thethicknessnone none noneCrack, surface crack existing only on the surface of thelaminatenone maximum length, 3.0 mm (1

18、8 in.) maximum length 6.5 mm (14 in.)Crazing fine cracks at or under the surface of alaminatenone maximum dimension of crazing, 13 mm(12 in.)maximum dimension of crazing, 25 mm(1 in.).frequency and location to be determined by customerDelamination, edge separation of the layers of material at the ed

19、geof a laminatenone maximum dimension, 3.0 mm (18 in.) maximum dimension, 6.5 mm (14 in.)Delamination,internalseparation of the layers of material in alaminatenone none noneDry-spot area of incomplete surface film where thereinforcement has not been wetted with resinnone maximum diameter, 9.5 mm (38

20、 in.) maximum diameter, 14 mm (916 in.)Foreign inclusion(metallic)metallic particles included in a laminate whichare foreign to its compositionnone none, if for electrical use; maximumdimension, 0.8 mm (132 in.), 1/0.09 m2(1 ft2), if for mechanical usenone, if for electrical use; maximumdimension, 1

21、.5 mm (116 in.), 1/0.09 m2(1 ft2), if for mechanical useForeign inclusion(nonmetallic)nonmetallic particles of substance included in alaminate which seem foreign to its compositionnone maximum dimension, 0.8 mm (132 in.),1/0.09 m2(1 ft2)maximum dimension, 1.5 mm (116 in.);1/0.09 m2(1 ft2)Fracture ru

22、pture of laminate surface without completepenetrationnone maximum dimension, 21 mm (1316 in.) maximum dimension, 29 mm (118 in.)Air bubble (void) air entrapment within and between the plies ofreinforcement, usually spherical in shapenone maximum diameter, 1.5 mm (116 in.);2/in.2maximum diameter, 3.0

23、 mm (18 in.);4/in.2Blister rounded elevation of the surface of a laminate,with boundaries that may be more or lesssharply defined, somewhat resembling in shapea blister on the human skinnone maximum diameter, 3.0 mm (18 in.);height from surface not to be outsidedrawing tolerancemaximum diameter, 6.5

24、 mm (14 in.);height from surface not to be outsidedrawing toleranceBurned showing evidence of thermal decompositionthrough some discoloration, distortion, ordestruction of the surface of the laminatenone none noneFish-eye small globular mass which has not blendedcompletely into the surrounding mater

25、ial and isparticularly evident in a transparent ortranslucent materialnone maximum diameter, 9.5 mm (38 in.) maximum diameter, 13 mm (12 in.)Lack of fillout an area, occurring usually at the edge of alaminated plastic, where the reinforcement hasnot been wetted with resinnone maximum diameter, 6.5 m

26、m (14 in.) maximum diameter, 9.5 mm (38 in.)Orange-peel uneven surface somewhat resembling anorange peelnone maximum diameter, 14 mm (916 in.) maximum diameter, 29 mm (118 in.)Pimple small, sharp, or conical elevation on thesurface of a laminatenone none maximum diameter, 3.0 mm (18 in.)Pit (pinhole

27、) small crater in the surface of a laminate, withits width approximately of the same order ofmagnitude as its depthnone maximum diameter, 0.4 mm (164 in.);depth less than 1 percent of wallthicknessmaximum diameter, 0.8 mm (132 in.);depth less than 20 percent of wallthicknessfrequency and location to

28、 be determined by customerPorosity (pinhole) presence of numerous visible pits (pinholes) none maximum of 25 pits (pinholes) inporous area of size listed in Level IImaximum of 50 pits (pinholes) inporous area of size listed in Level IIIPre-gel an unintentional extra layer of cured resin onpart of th

29、e surface of the laminate(This condition does not include gel coats.)none maximum dimension, 6.5 mm (14 in.);height above surface not to be outsidedrawing tolerancemaximum dimension, 13 mm (12 in.);height above surface not to be outsidedrawing toleranceResin-pocket an apparent accumulation of excess

30、 resin in asmall localized area within the laminatenone maximum diameter, 3.0 mm (18 in.) maximum diameter, 6.5 mm (12 in.)Resin-rich edge insufficient reinforcing material at the edge ofmolded laminatenone maximum, 0.4 mm (164 in.) from theedgemaximum, 0.8 mm (132 in.) from theedgeShrink-mark (sink

31、) depression in the surface of a molded laminatewhere it has retracted from the moldnone maximum diameter, 9.5 mm (38 in.);depth not greater than 25 percent ofwall thicknessmaximum diameter, 14 mm (916 in.);depth not greater than 25 percent ofwall thicknessWash area where the reinforcement of molded

32、 plastichas moved inadvertently during closure of themold resulting in resin-rich areasnone maximum dimension, 21 mm (1316 in.) maximum dimension, 29 mm (118 in.)Wormhole elongated air entrapment which is either in ornear the surface of a laminate and may becovered by a thin film of cured resinnone

33、maximum diameter, 3.0 mm (18 in.) maximum diameter, 6.5 mm (14 in.)Wrinkles in a laminate, an imperfection that has theappearance of a wave molded into one or moreplies of fabric or other reinforcement materialnone maximum length surface side, 13 mm(12 in.); maximum length opposite side,13 mm (12 in

34、.); depth less than 10percent of wall thicknessmaximum length surface side, 25 mm(1 in.); maximum length opposite side,25 mm (1 in.); depth less than 15percent of wall thicknessScratch shallow mark, groove, furrow, or channelcaused by improper handling or storagenone maximum length, 25 mm (1.0 in.);

35、maximum depth, 0.125 (0.005 in.)maximum length, 25 mm (1.0 in.);maximum depth, 0.255 (0.010 in.)D2563 08 (2015)2TABLE 1 ContinuedName DefinitionVisual Acceptance LevelsLevel I Level II Level IIIShort in a laminate, an incompletely filled outconditionNOTEthis may be evident either throughan absence o

36、f surface film in some areas, oras lighter unfused particles of material showingthrough a covering surface film, possiblyaccompanied by thin-skinned blistersnone none none2.8 Repairable DefectsRepairable defects, if any, shallconsist of those which can be repaired without affecting theserviceability

37、 of the part unless prohibited in the productdrawing or in the contract. Acceptable methods of repair shallbe agreed upon between the purchaser and the seller and shallbe only as specified in the product drawing or contracts for thepart.2.9 Surface FinishThe over-all surface finish of laminatesmay v

38、ary with the process used and the type of reinforcement.Unless surface finish is specified on part drawings, contracts, ororders from the purchaser, parts shall not be rejected for anyreading less than 150 rms. Defects shall be considered as notincluded in over-all surface finish.2.10 Surface Appear

39、anceThe surface appearance or color,or both, of laminated parts can vary considerably depending onthe process used to make the laminate, thickness, type ofreinforcement, type of resin, resin-to-reinforcement ratio andthe presence of defects. Any questions concerning surfaceappearance and its influen

40、ce on the properties of the partshould be brought to the attention of the responsible materialsengineer.3. Acceptance Levels3.1 Visual InspectionEach part shall be checked visuallywithout the aid of magnification. Defects shall be classified asto type and level as shown in Table 1 (see Note 2). Thea

41、cceptable quality level shall be determined by reference to thepart drawing for the applicable acceptance level for allowabledefects. If none of the first three levels (Level I, II, III) isconsidered applicable, the level shall be Level IV, and allow-able defects must be specified on the product dra

42、wing. Anyexcess of defects as specified under the required level shall because for rejection. Unless otherwise specified, dimensions aresurface dimensions.NOTE 2Typical defects as outlined in the word descriptions of Table1 are illustrated in Figs. 1-21.23.2 Acceptance Level IPresence of any defects

43、 in excessof those listed in Table 1, Level I, shall be cause for rejection,unless otherwise specified in Table 1, Level I.3.3 Acceptance Level IIPresence of more than one defectof those listed in Table 1, Level II, for each estimated 10 in.2of surface shall be cause for rejection, unless otherwises

44、pecified in Table 1, Level II. No defect area shall be less than2 in. from another.3.4 Acceptance Level IIIPresence of more than two de-fects of those listed in Table 1, Level III, for each estimated 13mm (5 in.)2of surface shall be cause for rejection, unlessotherwise specified in Table 1, Level II

45、I. No defect area shallbe less than 1 in. from another.3.5 Acceptance Level IVTo be specified on the productdrawing.4. Keywords4.1 reinforced thermosetting plastics; visual defects2Full-size (8 by 10-in.) glossy prints of these typical defects are available at anominal charge from ASTM Headquarters.

46、 Order Adjunct: ADJD2563.D2563 08 (2015)3FIG. 1 Chips (A), Surface Cracks (B), Interply Delamination (C)D2563 08 (2015)4FIG. 2 CrazingD2563 08 (2015)5FIG. 3 Delamination by Improper MachiningD2563 08 (2015)6FIG. 4 DelaminationD2563 08 (2015)7FIG. 5 Dry-SpotD2563 08 (2015)8FIG. 6 Foreign InclusionD25

47、63 08 (2015)9FIG. 7 FracturesD2563 08 (2015)10FIG. 8 BlisterD2563 08 (2015)11FIG. 9 Edge SegregationD2563 08 (2015)12FIG. 10 Fish EyeD2563 08 (2015)13FIG. 11 Lack of FilloutD2563 08 (2015)14FIG. 12 PorosityD2563 08 (2015)15FIG. 13 Pre-GelD2563 08 (2015)16FIG. 14 Resin-PocketD2563 08 (2015)17FIG. 15

48、Resin-Rich CrackD2563 08 (2015)18FIG. 16 Resin-Rich EdgeD2563 08 (2015)19FIG. 17 ScratchD2563 08 (2015)20FIG. 18 Shrink MarksD2563 08 (2015)21FIG. 19 WashD2563 08 (2015)22FIG. 20 Worm HoleD2563 08 (2015)23ASTM International takes no position respecting the validity of any patent rights asserted in c

49、onnection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for addit