ASTM C776-2006 Standard Specification for Sintered Uranium Dioxide Pellets《烧结的二氧化铀丸标准规范》.pdf

《ASTM C776-2006 Standard Specification for Sintered Uranium Dioxide Pellets《烧结的二氧化铀丸标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C776-2006 Standard Specification for Sintered Uranium Dioxide Pellets《烧结的二氧化铀丸标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C 776 06Standard Specification forSintered Uranium Dioxide Pellets1This standard is issued under the fixed designation C 776; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in paren

2、theses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis specification is intended to provide the nuclear industry with a general specification foruranium dioxide pellets. It recognizes the diversity o

3、f manufacturing methods by which uraniumdioxide pellets are produced and the many special requirements for chemical and physicalcharacterization which may be imposed by the operating conditions to which the pellets will besubjected in specific reactor systems. Therefore, it is anticipated that the p

4、urchaser may supplementthis specification with additional requirements for specific applications.1. Scope1.1 This specification is for finished sintered uranium diox-ide pellets. It applies to uranium dioxide pellets containinguranium of any235U concentration for use in nuclear reactors.1.2 This spe

5、cification recognizes the presence of repro-cessed uranium in the fuel cycle and consequently definesisotopic limits for uranium dioxide pellets made from commer-cial grade UO2. Such commercial grade UO2is defined so that,regarding fuel design and manufacture, the product is essen-tially equivalent

6、to that made from unirradiated uranium. UO2falling outside these limits cannot necessarily be regarded asequivalent and may thus need special provisions at the fuelfabrication plant or in the fuel design.1.3 This specification does not include (a) provisions forpreventing criticality accidents or (b

7、) requirements for healthand safety. Observance of this specification does not relieve theuser of the obligation to be aware of and conform to all federal,state, and local regulations pertaining to possessing, shipping,processing, or using source or special nuclear material. Ex-amples of U.S. Govern

8、ment documents are Code of FederalRegulations (Latest Edition), Title 10, Part 50, Title 10, Part 71,and Title 49, Part 173.1.4 The following precautionary caveat pertains only to thetechnical requirements portion, Section 4, of this specification:This standard does not purport to address all of the

9、 safetyconcerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety andhealth practices and determine the applicability or regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C 696 Test Methods for Chemical,

10、 Mass Spectrometric, andSpectrochemical Analysis of Nuclear-Grade Uranium Di-oxide Powders and PelletsC 753 Specification for Nuclear-Grade, Sinterable UraniumDioxide PowderC 859 Terminology Relating to Nuclear Materials3C 996 Specification for Uranium Hexafluoride Enriched toLess Than 5 %235UC 1233

11、 Practice for Determining Equivalent Boron Con-tents of Nuclear MaterialsE 105 Practice for Probability Sampling Of Materials2.2 ANSI Standard:4ANSI/ASME NQA-1 Quality Assurance Requirements forNuclear Facility Applications2.3 U.S. Government Documents:Code of Federal Regulations (Latest Edition), T

12、itle 10, Part50, Energy (10 CFR 50) Domestic Licensing of Produc-tion and Utilization Facilities5Code of Federal Regulations, Title 10, Part 71, Packagingand Transportation of Radioactive Material5Code of Federal Regulations, Title 49, Part 173, GeneralRequirements for Shipments and Packaging5Regula

13、tory Guide NUREG 1.126 AnAcceptable Model andRelated Statistical Methods for the Analysis of Fuel1This specification is under the jurisdiction of ASTM Committee C26 onNuclear Fuel Cycle and is the direct responsibility of Subcommittee C26.02 on Fueland Fertile Material Specifications.Current edition

14、 approved Aug. 1, 2006. Published September 2006. Originallyapproved in 1976. Last previous edition approved in 2000 as C 776 00.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume informati

15、on, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from American National Standards Institute, 11 W. 42nd St., 13thFloor, New York, NY 10036.5Available from Superintendent of Documents, U. S. Government PrintingOffice, Washington, DC 20402.1Copyright ASTM Inter

16、national, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Densification, Rev. 1 March 197863. Terminology3.1 DefinitionsFor definitions of terms, refer to Terminol-ogy C 859.4. Technical Requirements4.1 Chemical RequirementsAll chemical analyses shall beperformed

17、on portions of the representative sample prepared inaccordance with Section 6. Analytical chemistry methods usedshall be as stated in Test Methods C 696 (latest edition) ordemonstrated equivalent as mutually agreed upon between theseller and the buyer.4.1.1 Uranium Content The uranium content shall

18、be aminimum of 87.7 weight % on a dry weight basis. (Dry weightis defined as the sample weight minus the moisture content.)4.1.2 Impurity Content The impurity content shall notexceed the individual element limit specified in Table 1 on auranium weight basis. The summation of the contribution ofeach

19、of the impurity elements listed in Table 1 shall not exceed1500 g/g. If an element analysis is reported as “less than” agiven concentration, this “less than” value shall be used in thedetermination of total impurities.4.1.3 Stoichiometry The oxygen-to-uranium ratio of sin-tered fuel pellets shall be

20、 within the range from 1.99 to 2.02.4.1.4 Moisture Content The moisture content limit isincluded in the total hydrogen limit (see Table 1).4.2 Nuclear Requirements:4.2.1 Isotopic Content:4.2.1.1 For UO2pellets with an isotopic content of235Ubetween that of natural uranium and 5 %, the isotopic limit

21、sand radionuclide analytical requirements of SpecificationC 996 shall apply, unless otherwise agreed upon between thebuyer and the seller7. The specific isotopic measurementsrequired by Specification C 996 may be waived, provided thatthe seller can demonstrate compliance with SpecificationC 996, for

22、 instance, through the sellers quality assurancerecords.4.2.1.2 For UO2pellets not having an assay in the range setforth in 4.2.1.1, the isotopic requirements shall be as agreedupon between the buyer and the seller.4.2.2 Equivalent Boron ContentFor thermal reactor use,the total equivalent boron cont

23、ent (EBC) shall not exceed 4.0g/g on a uranium basis. The total EBC is the sum of theindividual EBC values. For purpose of EBC calculation B, Gd,Eu, Dy, Sm, and Cd shall be included in addition to elementslisted in Table 1 below. The method of performing thecalculation shall be as indicated in Pract

24、ice C 1233. For fastreactor use, the above limitation on EBC does not apply.4.3 Physical Characteristics:4.3.1 DimensionsThe dimensions of the pellet shall bespecified by the buyer. These shall include diameter, length,perpendicularity, and, as required, other geometric parametersincluding surface f

25、inish.4.3.2 Pellet Density The density of sintered pellets shallbe as specified by the buyer. The theoretical density for UO2ofnatural isotopic content shall be considered as 10.96 g/cm3.Density measurements shall be made by the geometric methodstated in the Specification C 753 Annex, an immersion m

26、ethodor by a demonstrated equivalent method as mutually agreedupon between the buyer and the seller.4.3.3 Grain Size and Pore MorphologyThe performanceof UO2fuel pellets may be affected by the grain size and poremorphology. These characteristics shall be mutually agreedupon between the buyer and the

27、 seller.4.3.4 Pellet Integrity Pellets shall be inspected to criteriawhich maintain adequate fuel performance and ensure thatexcessive breakage will not occur during fuel-rod loading.Acceptable test methods include a visual (13) comparisonwith pellet standards or other methods, for example, loadabil

28、itytests, approved by both the buyer and the seller.4.3.4.1 Surface Cracks The suggested limits for surfacecracks are defined as follows:(1) Axial Cracks, including those leading to the PelletEnds12 the pellet length.(2) Circumferential Cracks13 of the pellet circumfer-ence.4.3.4.2 ChipsThe limits f

29、or chips (missing material) areas follows:(1) Cylindrical Surface Chips(a)Cylindrical Surface Areathe total area of all chips shall beless than 5% of the pellet cylindrical surface area.(b)Maximum Linear Dimensionthe maximum linear dimen-sion shall be established to maintain adequate fuel performanc

30、ein the intended application and shall be agreed upon betweenthe buyer and the seller.(2) Pellet Ends13 of the pellet end surface (may beinspected as13 of missing circumference at the pellet end).4.3.5 Cleanliness and WorkmanshipThe surface of fin-ished pellets shall be visually free of macroscopic

31、inclusionsand foreign material such as oil and grinding media.4.4 Identification Pellets may be identified as to enrich-ment by either marking or coding.6Available from U.S. Nuclear Regulatory Commission, Washington, DC 20555.Attention: Director, Division of Document Control.7A236U content greater t

32、han the one specified in Specification C 996 forCommercial grade UF6may be acceptable for the intended application since it is nota radiological safety concern. The intent of the C 996 isotope limits is to indicatepossible presence of reprocessed UF6. Acceptance of UO2pellets with a236Ucontent above

33、 that specified for Commercial Enriched UF6, shall be based on a fuelperformance evaluation.TABLE 1 Impurity Elements and Maximum Concentration LimitsElementMaximum ConcentrationLimit (g/g U)Aluminum 250Carbon 100Calcium + magnesium 200Chlorine 25Chromium 250Cobalt 100Fluorine 15Hydrogen (total from

34、 all sources) 1.3Iron 500Nickel 250Nitrogen 75Silicon 500Thorium 10C7760624.5 Irradiation Stability (Densification)An estimate of thefuel pellet irradiation stability shall be obtained (maximumdensification anticipated) unless adequate allowance for sucheffects is factored into the fuel rod design.

35、The estimation ofthe stability shall consist of either (a) conformance to thethermal stability test as specified in US NRC Regulatory GuideNUREG 1.126,or(b) by adequate correlation of manufactur-ing process or microstructure to in-reactor behavior, or both.5. Lot Requirements5.1 A pellet lot is defi

36、ned as a group of pellets made from asingle uranium dioxide powder lot as defined in SpecificationC 753 using one set of process parameters.5.2 The identity of a pellet lot shall be retained throughoutprocessing without mixing with other established lots.5.3 Conformance to this specification shall b

37、e establishedfor each pellet lot.6. Sampling6.1 Uranium dioxide pellets may be hygroscopic and retainsufficient water after exposure to a moist atmosphere. Sam-pling and handling the sample shall be done under conditionswhich assure that the sample is representative of the lot.Practice E 105 is refe

38、renced as a guide.6.2 The buyer shall have the option to take a representativesample of pellets from each pellet lot for the purpose ofdetermining chemical, nuclear, or physical properties.6.3 The lot sample shall be of sufficient size to performquality assurance testing at the sellers plant, refere

39、e testing inthe event it becomes necessary, and, when required, acceptancetesting at the buyers plant.6.4 The lot sample for acceptance testing at the buyersplant, when required, shall be packaged in a separate container,clearly identified by lot number, and shipped preceding or withthe lot. The ref

40、eree sample shall be clearly identified andretained at the sellers plant until the lot has been formallyaccepted by the buyer.7. Testing and Certification7.1 The seller shall test the sample described in Section 6 toassure conformance of the pellet lot to the requirements ofSection 4. All testing sh

41、all be conducted by techniques mutu-ally agreed to between the buyer and the seller.7.2 The seller shall provide to the buyer documentationcertifying that the pellets meet all the requirements of Section4.7.3 For a time period to be agreed upon by the buyer and theseller, the seller shall maintain a

42、nd make available uponrequest all results used to certify that pellets meet the require-ments of Section 4.7.4 Lot AcceptanceAcceptance testing may be performedby the buyer on either the sample provided by the seller or ona sample taken at the buyers plant. Acceptance shall be on apellet lot basis a

43、nd shall be contingent upon the materialproperties meeting the requirements of Section 4 as modifiedby contract documentation.7.5 RefereeThe buyer and seller shall agree to a thirdparty as a referee in the event of a dispute in analytical results.8. Packaging and Shipping8.1 Uranium dioxide pellets

44、shall be packaged in sealedcontainers to prevent loss or damage of material and contami-nation from airborne or container materials. The exact size andtype of packaging shall be as mutually agreed upon betweenthe buyer and the seller.8.2 Each container in 8.1 shall bear labels on the lid and sidetha

45、t include the required to satisfy the appropriate transporta-tion and regulatory requirements, including as a minimum thefollowing:8.2.1 Sellers name,8.2.2 Material in container,8.2.3 Lot number,8.2.4 Uranium enrichment,8.2.5 Gross, tare, net oxide weights,8.2.6 Uranium weight,8.2.7 Purchase order n

46、umber, and8.2.8 Container ( ) of ( ).9. Quality Assurance9.1 Quality assurance requirements shall be agreed uponbetween the buyer and the seller when specified in the purchaseorder. Code of Federal Regulations Title 10, Part 50, AppendixB and ANSI/ASME NQA-1 are referenced as guides.10. Keywords10.1

47、 nuclear fuel; nuclear fuel pellets; urania; uraniumdioxideC776063APPENDIX(Nonmandatory Information)X1. PELLET LOADABILITY TESTX1.1 Randomly selected samples (the number of samplesto be established by statistical considerations) shall be sub-jected to an axial load representative of fuel rod loading

48、conditions at the fabrication plant. Each test sample shallconsist of ten finished pellets. Samples shall be subjected to anaxial load that is 125% of the maximum load applied duringpellet loading without producing a chip with a maximum lineardimension in excess of that agreed upon between the buyer

49、 andseller.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited eith