ASTM B792-2001(2005)e1 Standard Specification for Zinc Alloys in Ingot Form for Slush Casting《空壳铸造用铸模中的锌合金锭标准规范》.pdf

《ASTM B792-2001(2005)e1 Standard Specification for Zinc Alloys in Ingot Form for Slush Casting《空壳铸造用铸模中的锌合金锭标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM B792-2001(2005)e1 Standard Specification for Zinc Alloys in Ingot Form for Slush Casting《空壳铸造用铸模中的锌合金锭标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 792 01 (Reapproved 2005)e1Standard Specification forZinc Alloys in Ingot Form for Slush Casting1This standard is issued under the fixed designation B 792; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of l

2、ast revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.e1NOTEAn editorial change was made to paragraph 1.2 in November 2005.1. Scope*1.1 This specification covers commercial zinc alloys

3、 iningot form for remelting for the manufacture of castings fromthe alloys as specified and designated as shown in Table 1.1.2 Slush casting alloys are used primarily for the manufac-ture of hollow castings such as lighting fixtures, lamp bases,and small statues.1.3 This specification covers two zin

4、c alloys which arespecified and designated as follows:UNS ASTMZ34510 Slush Casting Alloy AZ30500 Slush Casting Alloy B1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onl

5、yand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (

6、MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on dateof order acceptance form a part

7、of this specification to theextent referenced herein:2.2 ASTM Standards:2B 899 Terminology Relating to Non-ferrous Metals andAlloysB 908 Practice for the Use of Color Codes for Zinc CastingAlloy IngotE29 Practice for Using Significant Digits in Test Data toDetermine Conformance With SpecificationsE4

8、7 Test Methods for Chemical Analysis of Zinc Die-Casting Alloys3E88 Practice for Sampling Nonferrous Metals and Alloysin Cast Form for Determination of Chemical CompositionE 527 Practice for Numbering Metals and Alloys (UNS)E 536 Test Methods for ChemicalAnalysis of Zinc and ZincAlloys3. Terminology

9、3.1 Terms shall be defined in accordance with TerminologyB 899.4. Ordering Information4.1 Orders for ingots under this specification shall includethe following information:4.1.1 Quantity in pounds,4.1.2 Alloy (Table 1),1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous

10、Metals and Alloys and is the direct responsibility of SubcommitteeB02.04 on Zinc and Cadmium.Current edition approved Nov. 1, 2005. Published November 2005. Originallyapproved in 1988. Last previous edition approved in 2001 as B 792 01e1.2For referenced ASTM standards, visit the ASTM website, www.as

11、tm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.TABLE 1 Chemical and North American Color CodeRequirementsA,BComposition, %UNS Z34510Slush Casting Alloy AUNS Z3

12、0500Slush Casting Alloy BColor CodeCBlack/Red Black/OrangeElementCopper 0.20.3 0.1 maxAluminum 4.505.00 5.255.75Lead 0.007 max 0.007 maxCadmium 0.005 max 0.005 maxTin 0.005 max 0.005 maxIron 0.100 max 0.100 maxMagnesium 0.010 max 0.010 maxZinc Remainder RemainderAThe following applies to all specifi

13、ed limits in this table. For purposes ofdetermining conformance with this specification, the observed or calculated valueobtained from analysis shall be rounded off “to the nearest unit in the lastright-hand place of figures used in expressing the specified limit, in accordancewith the rounding meth

14、od of Practice E29.BUNS designations were established in accordance with Practice E 527.CRefer to Practice B 908. (Note: Colors indicated are for North Americanapplications.)1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box

15、 C700, West Conshohocken, PA 19428-2959, United States.4.1.3 Size, if not manufacturers standard,4.1.4 Specification number and date,4.1.5 Source inspection (Section 7), and4.1.6 Marking (Section 9).5. Materials and Manufacture5.1 The alloys may be made by any approved process.5.2 The material cover

16、ed by this specification shall be ofuniform quality and shall be free from dross, slag, or otherharmful contamination. The ingot shall also be reasonably freeof surface corrosion and adhering foreign matter.6. Chemical Requirements Chemical Requirements6.1 LimitsThis alloy shall conform to the requi

17、rements asto chemical composition prescribed in Table 1. Conformanceshall be determined by the producer by analyzing samplestaken at the time the ingots are made. If the producer hasdetermined the chemical composition of the metal during thecourse of manufacture, he shall not be required to sample a

18、ndanalyze the finished product.6.2 In case of dispute, the following requirements shallapply:6.2.1 Number of SamplesSamples for verification ofchemical composition shall be taken as follows:6.2.1.1 If the ingots are shipped in carload lots of the samealloy, not less than five ingots shall be taken a

19、t random fromthe carload for sampling. If the shipment is less than a carloadlot, one sample ingot shall be taken for each 10 000 lb (4 500kg) or fraction thereof. When it is deemed necessary, a samplemay be taken from each melt of 1 000 lb (450 kg) or more.6.3 Methods of SamplingSamples from ingots

20、 for deter-mination of chemical composition shall be taken in accordancewith one of the following methods:6.3.1 Samples for chemical analysis shall be taken from thematerial by drilling, sawing, milling, turning, or clipping arepresentative piece or pieces to obtain weight of preparedsample not less

21、 than 100 g. Sampling shall be in accordancewith Practice E88.6.3.2 By agreement, an optional method of sampling foranalysis may be by melting together representative portions ofeach ingot selected, and then sampling the liquid composite bycasting suitable specimens for either spectrographic or chem

22、i-cal analysis.6.3.3 Sample may also be in the form of a separately castspectrographic specimen taken from the same pour used to castthe ingot.6.4 Method of AnalysisThe determination of chemicalcomposition shall be made in accordance with suitable chemi-cal (Test Methods E 536 or Test Method E47for

23、tin) or othermethods. In case of dispute, the results secured by TestMethods E 536 and Test Method E47for tin only shall be thebasis of acceptance.7. Source Inspection7.1 If the purchaser desires that his representative inspect orwitness the inspection and testing of the product prior toshipment, su

24、ch agreement shall be made by the purchaser andproducer or supplier as part of the contract or purchase order.7.2 When such inspection or witness of inspection andtesting is agreed upon, the producer or supplier shall afford thepurchasers representative all reasonable facilities to satisfyhim that t

25、he product meets the requirements of this specifica-tion. Inspection and tests shall be conducted so there is nounnecessary interference with the producers operations.8. Rejection and Rehearing8.1 Material that fails to conform to the requirements of thisspecification may be rejected. Rejection shou

26、ld be reported tothe producer or supplier promptly and in writing. In case ofdissatisfaction with the results of the test, the producer orsupplier may make claim for a rehearing. If the rehearingestablishes that the material does not conform to the require-ments of this specification, as much of the

27、 rejected originalmaterial as possible shall be returned to the producer orsupplier.9. Identification Marking9.1 All ingots shall be properly marked for identificationwith the producers name or brand.9.2 Each bundle or skid shall be identified with the produc-ers heat, lot, or other identification m

28、ark.9.3 Each ingot, bundle or skid shall be marked with theappropriate Color Code for the alloy as per North AmericanRequirements in Practice B 908.10. Preparation for Delivery10.1 PackagingUnless otherwise specified, the ingot shallbe packaged to provide adequate protection during normalhandling an

29、d transportation. Each package shall contain onlyone alloy unless otherwise agreed upon.11. Keywords11.1 casting; casting alloys; gravity casting; permanentmold casting; slush casting; zinc; zinc alloysB 792 01 (2005)e12SUMMARY OF CHANGESThis section contains the principal changes to the standard th

30、at have been incorporated since the last issue.(1) Practice B 908 was added to Referenced Documents.(2) North American Color Code Requirements added to Table1.(3) Color Code requirement added to Identification Marking.ASTM International takes no position respecting the validity of any patent rights

31、asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any tim

32、e by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will r

33、eceive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM I

34、nternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).B 792 01 (2005)e13