ASTM B333-2003(2008) Standard Specification for Nickel-Molybdenum Alloy Plate Sheet and Strip《镍钼合金板、薄板和带材标准规范》.pdf

《ASTM B333-2003(2008) Standard Specification for Nickel-Molybdenum Alloy Plate Sheet and Strip《镍钼合金板、薄板和带材标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM B333-2003(2008) Standard Specification for Nickel-Molybdenum Alloy Plate Sheet and Strip《镍钼合金板、薄板和带材标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 333 03 (Reapproved 2008)Standard Specification forNickel-Molybdenum Alloy Plate, Sheet, and Strip1This standard is issued under the fixed designation B 333; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、 last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification2covers plate, she

3、et, and strip ofnickel-molybdenum alloys (UNS N10001, N10665, N10675,N10629, and N10624)* as shown in Table 1, for use in generalcorrosive service.1.2 The following products are covered under this specifi-cation:1.2.1 Sheet and StripHot or cold rolled, solution an-nealed, and descaled unless solutio

4、n anneal is performed in anatmosphere yielding a bright finish.1.2.2 PlateHot or cold rolled, solution annealed, anddescaled.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for informat

5、ion onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data

6、Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3B 906 Specification for General Requirements for Flat-Rolled Ni

7、ckel and Nickel Alloys Plate, Sheet, and StripE112 Test Methods for Determining Average Grain SizeE 140 Hardness Conversion Tables for Metals RelationshipAmong Brinell Hardness, Vickers Hardness, RockwellHardness, Superficial Hardness, Knoop Hardness, andScleroscope Hardness3. Terminology3.1 Definit

8、ions of Terms Specific to This Standard:3.1.1 cold-rolled plate, nmaterial316 to38 in. (4.76 to9.52 mm), inclusive, in thickness.1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel

9、 and Cobalt and Their Alloys.Current edition approved Nov. 1, 2008. Published November 2008. Originallyapproved in 1958. Last previous edition approved in 2003 as B 333 03.* New designation established in accordance withASTM E 527 and SAE J 1086,Practice for Numbering Metals and Alloys (UNS).2For AS

10、ME Boiler and Pressure Vessel Code applications, see related Specifi-cation SB-333 in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the st

11、andards Document Summary page onthe ASTM website.TABLE 1 Chemical RequirementsElementComposition Limits, %AlloyN10001AlloyN10665AlloyN10675AlloyN10629AlloyN10624Nickel remainderAremainderA65.0 min remainderABalMolybdenum 26.030.0 26.030.0 27.032.0 26.030.0 21.0-25.0Iron 4.06.0 2.0 max 1.03.0 1.06.0

12、5.0-8.0Chromium 1.0 max 1.0 max 1.03.0 0.51.5 6.0-10.0Carbon, max 0.05 0.02 0.01 0.01 0.01Silicon, max 1.0 0.10 0.10 0.05 0.10Cobalt, max 2.5 1.00 3.0 2.5 1.0Manganese,max1.0 1.0 3.0 1.5 1.0Phosphorus,max0.04 0.04 0.030 0.04 0.025Sulfur, max 0.03 0.03 0.010 0.01 0.01Vanadium 0.20.4 . 0.20 max . .Nic

13、kel plusMolybdenum. . 94.098.0 .Aluminum . . 0.50 max 0.10.5 0.5Columbium(Nb), max. . 0.20 .Copper, max . . 0.20 0.5 0.5Tantalum,max. . 0.20 .Titanium,max. . 0.20 .Tungsten,max. . 3.0 .Zirconium,max. . 0.10 .Magnesium,max. . . . .ASee Specification B 906.1Copyright ASTM International, 100 Barr Harbo

14、r Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.2 hot-rolled plate, nmaterial316 in. (4.76 mm) andover in thickness.3.1.3 plate, nmaterial316 in. (4.76 mm) and over inthickness.3.1.4 sheet and strip, nmaterial under316 in. (4.76 mm) inthickness.4. General Requirements4.1 Ma

15、terial furnished under this specification shall con-form to the applicable requirements of Specification B 906unless otherwise provided herein.5. Ordering Information5.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecificati

16、on. Examples of such requirements include, but arenot limited to the following:5.1.1 AlloyTable 1,5.1.2 DimensionsThickness (in decimals of an inch),width, and length (inch or fractions of an inch),5.1.3 Optional RequirementPlate; how the plate is to becut (Specification B 906, Table A2.3)5.1.4 Cert

17、ificationState if certification or a report of testresults is required (Specification B 906, Section 21),5.1.5 Purchase InspectionState which tests or inspectionsare to be witnessed (Specification B 906, Section 18), and5.1.6 Samples for Product (Check) AnalysisState whethersamples should be furnish

18、ed (Specification B 906, Section7.2.2).6. Chemical Composition6.1 The material shall conform to the composition limitsspecified in Table 1.6.2 If a product (check) analysis is made by the purchaser,the material shall conform to the requirements specified inTable 1 and Specification B 906.7. Mechanic

19、al Properties and Other Requirements7.1 Tensile PropertiesThe material shall conform to theroom temperature tensile properties prescribed in Table 2.7.2 HardnessThe hardness values given in Table 2 areinformative only.7.3 Grain Size for Sheet and StripSheet and strip shallconform to the grain sizes

20、as illustrated in Plate 1 of TestMethods E112. The requirements shall be as indicated in Table3.8. Dimensions, Mass, and Permissible Variations8.1 WeightFor calculations of mass or weight, the follow-ing densities shall be used:DensityAlloy lb/in.3(g/cm3)N10001 0.334 (9.24)N10665 0.333 (9.22)N10675

21、0.333 (9.22)N10629 0.333 (9.22)N10624 0.322 (8.9)8.2 Thickness:8.2.1 Sheet and StripThe thickness shall be measuredwith the micrometer spindle38 in. (9.525 mm) or more fromany edge for material 1 in. (25.4 mm) or over in width and atany place on material under 1 in. (25.4 mm) in width.8.3 Length:8.3

22、.1 Sheet and StripSheet and strip may be ordered to cutlengths, in which case a variation of18 in. (3.175 mm) over thespecified length shall be permitted, with a 0 minus tolerance.8.4 Straightness:8.4.1 The edgewise curvature (depth of chord) of flat sheet,strip, and plate shall not exceed 0.05 in.

23、(1.27 mm) multipliedby the length in feet or 0.04 mm multiplied by the length incentimetres.8.4.2 Straightness for coiled strip is subject to agreementbetween the manufacturer and the purchaser.TABLE 2 Mechanical Property RequirementsAlloyThickness,in. (mm)Tensile Strength,min, psi (MPa)Yield Streng

24、th(0.2 % Offset),min, psi (MPa)Elongationin2in.(50.8 mm)or 4DAmin, %RockwellHardness,BmaxSheet and StripN10001 Under316 (4.76) 115 000 (795) 50 000 (345) 45 100 HRBN10665 Under316 (4.76) 110 000 (760) 51 000 (350) 40 100 HRBN10675 Under316 (4.76) 110 000 (760) 51 000 (350) 40 100 HRBN10629 Under316

25、(4.76) 110 000 (760) 51 000 (350) 40 100 HRBN10624 Under316 (4.76) 104 000 (720) 46 000 (320) 40 100 HRBPlateN10001316 to 212 in. (4.76 to 63.5 mm), incl 100 000 (690) 45 000 (310) 40 100 HRBN10665316 to 212 in. (4.76 to 63.5 mm), incl 110 000 (760) 51 000 (350) 40 100 HRBN10675316 to 212 in. (4.76

26、to 63.5 mm), incl 110 000 (760) 51 000 (350) 40 100 HRBN10629316 to 212 in. (4.76 to 63.5 mm), incl 110 000 (760) 51 000 (350) 40 100 HRBN10624316 to 212 in. (4.76 to 63.5 mm), incl 104 000 (720) 46 000 (320) 40 100 HRBAD refers to the diameter of the tension specimen.BHardness values are shown for

27、information purposes only and are not to be used as a basis for rejection or acceptance. For approximate hardness conversions, seeHardness Conversion Tables E 140.TABLE 3 Grain Size for Annealed SheetThickness,in. (mm)ASTM MicrograinSize Number,maxAverage GrainDiameter, max,mm (in.)0.125 (3.175) and

28、 under 3.0 0.127 (0.0050)Over 0.125 (3.175) 1.5 0.214 (0.0084)B 333 03 (2008)28.5 Squareness (Sheet)For sheets of all thicknesses andwidths of 6 in. (152.4 mm) or more, the angle between adjacentsides shall be 90 6 0.15 degrees (116 in. in 24 in. or 2.6mm/m).8.6 FlatnessPlate, sheet, and strip shall

29、 be commerciallyflat.8.7 Edges:8.7.1 Plates shall have sheared, abrasive cut, or plasma-torch-cut edges as specified.8.7.2 Sheet and strip shall have sheared or slit edges.9. Product Marking9.1 Each plate, sheet, or strip shall be marked on one facewith the specification number, alloy, heat number,

30、manufactur-ers identification, and size. The markings shall have nodeleterious effect on the material or its performance and shallbe sufficiently stable to withstand normal handling.9.2 Each bundle or shipping container shall be marked withthe name of the material; this specification number; alloy;

31、thesize; gross, tare, and net weight; consignor and consigneeaddress; contract or order number; and such other informationas may be defined in the contract or order.10. Keywords10.1 plate; sheet; strip; UNS N10001; UNS N10629; UNSN10665; UNS N10675; UNS N10624APPENDIX(Nonmandatory Information)X1. HE

32、AT TREATMENTX1.1 Proper heat treatment during or subsequent to fabri-cation is necessary for optimum performance, and themanufacturer shall be consulted for details.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this

33、 standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be

34、reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of therespo

35、nsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, Wes

36、t Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).B 333 03 (2008)3