ASTM A582 A582M-2005 Standard Specification for Free-Machining Stainless Steel Bars《高速切削不锈钢棒材的标准规范》.pdf

《ASTM A582 A582M-2005 Standard Specification for Free-Machining Stainless Steel Bars《高速切削不锈钢棒材的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM A582 A582M-2005 Standard Specification for Free-Machining Stainless Steel Bars《高速切削不锈钢棒材的标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 582/A 582M 05Standard Specification forFree-Machining Stainless Steel Bars1This standard is issued under the fixed designation A 582/A 582M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision.

2、A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification covers hot-finished or cold-fin

3、ishedbars, except bars for forging (Note 1), suitable for machiningprocesses. It includes rounds, squares, and hexagons in themore commonly used types of stainless free-machining steelsdesigned especially for optimum machinability and for generalcorrosion and high-temperature service. Stainless stee

4、l barsother than the free-machining types are covered in a separatespecification (Note 2).1.2 This specification is expressed in both inch-pound unitsand in SI units; however, unless the purchase order or contractspecifies the applicable M specification designation (SI units),the inch-pound units sh

5、all apply. The values stated in eitherinch-pound units or SI (metric) units are to be regardedseparately as standard: within the text and tables, the SI unitsare shown in brackets. The values stated in each system maynot be exact equivalents: therefore, each system shall be usedindependently of the

6、other. Combining values from the twosystems may result in nonconformance with the specification.NOTE 1For bars for reforging, see Specification A 314.NOTE 2For non-free machining stainless bars, see SpecificationA 276.2. Referenced Documents2.1 ASTM Standards:2A 276 Specification for Stainless Steel

7、 Bars and ShapesA 314 Specification for Stainless Steel Billets and Bars forForgingA 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 484/A 484M Specification for General Requirements forStainless Steel Bars, Billets, and ForgingsA 751 Test Methods, Practices, and Terminolog

8、y forChemical Analysis of Steel ProductsA 959 Guide for Specifying Harmonized Standard GradeCompositions for Wrought Stainless SteelsE 527 Practice for Numbering Metals and Alloys (UNS)2.2 SAE Document:3SAE J 1086 Recommended Practice for Numbering Metalsand Alloys33. Ordering Information3.1 It is t

9、he responsibility of the purchaser to specify allrequirements that are necessary for product ordered under thisspecification. Such requirements to be considered include, butare not limited to, the following:3.1.1 Quantity (weight or number of pieces),3.1.2 Type or UNS designation (Table 1),3.1.3 For

10、m (bars, angles, etc.),3.1.4 Condition (Table 2),3.1.5 Finish (5.1),3.1.6 Applicable dimensions, including size, thickness,width, and length,3.1.7 Cross section (round, square, etc.),3.1.8 ASTM designation (Specification A 582/A 582M) andpublication date,3.1.9 Preparation for delivery, and3.1.10 Mar

11、king requirements.NOTE 3Atypical ordering description is as follows: 5000 lb 2000 kgType 416 bars, annealed and centerless ground, 112 in. 40 mm round, 10to 12 ft 3 to 4 m in length, ASTM Specification A 582/A 582M dated.4. General Requirements for Delivery4.1 Product furnished to this specification

12、 shall conform tothe requirements of Specification A 484/A 484M, includingany supplementary requirements indicated in the purchaseorder or contract. Failure to comply with the general require-ments of Specification A 484/A 484M constitutes nonconfor-mance with this specification. In case of conflict

13、 between therequirements of this specification and Specification A 484/A 484M, this specification shall prevail.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.17 on Flat-Rolled and Wr

14、ought Stainless Steel.Current edition approved March 1, 2005. Published March 2005. Originallyapproved in 1967. Last previous edition approved in 2000 as A 582/A 582M 95b(2000)e1.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org.

15、 For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Society of Automotive Engineers (SAE), 400 CommonwealthDr., Warrendale, PA 15096-0001.1*A Summary of Changes section appears at the end of this standard.Copyright AST

16、M International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Materials and Manufacture5.1 Bars may be furnished either hot finished or coldfinished in one of the conditions listed in Table 2.5.2 Surface finishing shall be performed in accordance withfinishi

17、ng methods as defined in Specification A 484/A 484M.6. Chemical Requirements6.1 The chemical composition shall conform to the require-ments specified in Table 1.6.2 Methods and practices relating to chemical analysisrequired by this specification shall be in accordance with TestMethods, Practices, a

18、nd Terminology A 751.7. Hardness Requirement7.1 The product shall conform with the hardness require-ments listed in Table 3 for Brinell Hardness Number (HB).7.2 At least one hardness test shall be made midwaybetween surface and center on each lot to determine that thematerial conforms to Table 3.7.2

19、.1 Hardness testing shall be performed in accordancewith Test Methods and Definitions A 370.7.2.2 For sizes below 1 in. 25 mm cross section, it ispermitted to determine the hardness value by tensile test withconversion to hardness in accordance with Test Methods andDefinitions A 370.8. Certification

20、8.1 Certificate of ComplianceWhen specified in the pur-chase order or contract, the producer or supplier shall furnish acertificate of compliance stating that the product was manu-factured, sampled, tested, and inspected in accordance with thisspecification (including year date) and any other requir

21、ementsdesignated in the purchase order or contract, and has beenfound to meet such requirements.TABLE 1 Chemical RequirementsUNSDesig-nationATypeChemical Composition, %CarbonBManga-neseBPhos-phorus,BSulfurBSilicon,maxChromium NickelMolyb-denumSeleniumOtherElementsAusteniticS20300 XM-1 0.08 5.06.5 0.

22、04 0.180.35 1.00 16.018.0 5.06.5 . . . . . . Cu 1.752.25S30300 303 0.15 2.00 0.20 0.15 min 1.00 17.019.0 8.010.0 . . . . . . . . .S30310 XM-5 0.15 2.54.5 0.20 0.25 min 1.00 17.019.0 7.010.0 . . . . . . . . .S30323 303Se 0.15 2.00 0.20 0.06 1.00 17.019.0 8.010.0 . . . 0.15 min . . .S30345 XM-2 0.15 2

23、.00 0.05 0.110.16 1.00 17.019.0 8.010.0 0.400.60 . . . Al 0.601.00MartensiticS41600 416 0.15 1.25 0.06 0.15 min 1.00 12.014.0 . . . . . . . . . . . .S41610 XM-6 0.15 1.502.50 0.06 0.15 min 1.00 12.014.0 . . . . . . . . . . . .S41623 416Se 0.15 1.25 0.06 0.06 1.00 12.014.0 . . . . . . 0.15 min . . .S

24、42020 420F 0.300.40 1.25 0.06 0.15 min 1.00 12.014.0 0.50C. . Cu0.60CS42023 420FSe 0.200.40 1.25 0.06 0.06 1.00 12.014.0 0.50C. . . 0.15 min Cu 0.60CS44020 440F 0.951.20 1.25 0.06 0.15 min 1.00 16.018.0 0.50C. . Cu0.60CS44023 440FSe 0.951.20 1.25 0.06 0.06 1.00 16.018.0 0.50C. . . 0.15 min Cu 0.60CF

25、erriticS18200 XM-34 0.08 2.50 0.04 0.15 min 1.00 17.519.5 . . . 1.502.50 . . . . . .S18235 . . . 0.025 0.50 0.030 0.150.35 1.00 17.518.5 1.00 2.002.50 . . . Ti 0.301.00N 0.025C+N 0.035S41603 . . . 0.08 1.25 0.06 0.15 min 1.00 12.0-14.0 . . . . . . . . . . . .S43020 430F 0.12 1.25 0.06 0.15 min 1.00

26、16.018.0 . . . . . . . . . . . .S43023 430FSe 0.12 1.25 0.06 0.06 1.00 16.018.0 . . . . . . 0.15 min . . .ADesignation established in accordance with Practice E 527 and SAE J 1086, Recommended Practice for Numbering Metals and Alloys (UNS).BMaximum unless otherwise noted.CAt manufacturers option, re

27、ported only when intentionally added.TABLE 2 ConditionType Condition A(Annealed)Condition T(IntermediateTemper)Condition H(Hard Temper)XM-1 A . . .303 A . .XM-5 A . .303Se A . . . . . .XM-2 A . .416 A T HXM-6 A T H416Se A T H420F A . . . . . .420FSe A . . . . . .440F A . . . . . .440FSe A . . . . .

28、.XM-34 A . .S18235 A . . . . . .S41603 A . . . . . .430F A . . . . . .430FSe A . . . . . .TABLE 3 Mechanical Test RequirementsTypes Condition HardnessA(HB)All (except 440F, 440FSe and S18235) A 262 max416, 416Se, 420FSe, and XM-6 T 248 to 302416, 416Se, and XM-6 H 293 to 352440 F and 440FSe A 285 ma

29、xS18235 A 207 maxASizes below approximately 1 in. 25 mm cross section may be tensile testedand converted to hardness in accordance with Test Methods and Definitions A 370.A 582/A 582M 0528.2 Test ReportsWhen specified in the purchase order orcontract, test reports shall be furnished to the purchaser

30、containing the results of all tests and chemical analysesrequired by this specification (including year date), and anyother requirements designated in the purchase order or con-tract.9. Keywords9.1 austenitic stainless steel; ferritic stainless steel; free-machining stainless steel; martensitic stai

31、nless steel; stainlesssteel barsAPPENDIX(Nonmandatory Information)X1. CROSS REFERENCEX1.1 This table is intended to assist the user whenSpecification A 582/A 582M is referenced in a governmentprocurement. It shows the types of steels in SpecificationA 582/A 582M replacing the steels formerly specifi

32、ed in QQ-S-764B.TABLE X1.1 Cross ReferenceUNS DesignationAQQ-S-764BSpecification A 582,TypeS20300 203EZ XM-1S30300 303 303S30310 303 Plus X XM-5S30323 303Se 303SeS30345 303Ma XM-2S41600 416 416S41610 416 Plus X XM-6S41623 416Se 416SeS42020 420F 420FS42023 420FSe 420FSeS43020 430F 430FS43023 430FSe 4

33、30FSeADesignation established in accordance with Practice E 527 and SAE J 1086, Recommended Practice for Numbering Metals and Alloys (UNS).SUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to this standard since the last issue,A 582/A 582M 95b (2000)e1, that may impact

34、the use of this standard. (Approved March 1, 2005.)(1) The following sections were modified to conform withcurrent form and style practices: Scope, Referenced Docu-ments, Ordering Information, General Requirements, and Cer-tification.(2) Section 2 was revised to include references to Test Meth-ods a

35、nd Definitions A 370 and Specification A 484/A 484M.(3) Section 5, Materials and Manufacture, was updated toinclude a description of finishing processes.(4) Section 7, Hardness Requirements, was updated to specifyhardness and conversion factor requirements.(5) Table 1 was revised for compliance with

36、 Guide A 959regarding the number of digits in the composition listed.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of an

37、y such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are i

38、nvited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not receiv

39、ed a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).A 582/A 582M 053