ASD-STAN PREN 6075-2015 Aerospace series Static seal elements O-Ring ethylene-propylene moulded phosphate ester resistant (- 55 to 107 Inch series (Edition P 2).pdf
《ASD-STAN PREN 6075-2015 Aerospace series Static seal elements O-Ring ethylene-propylene moulded phosphate ester resistant (- 55 to 107 Inch series (Edition P 2).pdf》由会员分享,可在线阅读,更多相关《ASD-STAN PREN 6075-2015 Aerospace series Static seal elements O-Ring ethylene-propylene moulded phosphate ester resistant (- 55 to 107 Inch series (Edition P 2).pdf(15页珍藏版)》请在麦多课文档分享上搜索。
1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 6075 Edition P 2 April 2015 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: Supersedes edition P 1 of Decemb
2、er 2004 Descriptors: ENGLISH VERSION Aerospace series Static seal elements O-Ring ethylene-propylene, moulded, phosphate ester resistant ( 55 C to 107 C) Inch series Srie arospatiale Joint torique statique thylne-propylne, moul, rsistant lester phosphorique ( 55 C 107 C) Srie en inches Luft- und Rau
3、mfahrt Statische Dichtungen O-Ringe Ethylen-Propylen, geformt, bestndig gegen Phosphorsureester ( 55 C bis 107 C) Inch Reihe This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It i
4、s published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affec
5、ted, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full Euro
6、pean Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1st April 2015 Comments should be sent within six months
7、 after the date of publication to ASD-STAN Mechanical Domain Copyright 2015 by ASD-STAN prEN 6075:2015 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Requirements . 3 4 Designation 13 5 Marking and packaging .13 6 Technical specification .14 7 Quality assurance 14 Annex A (infor
8、mative) Standard evolution form .15 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Mechanical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval
9、for Publication. prEN 6075:2015 (E) 3 1 Scope This standard specifies the characteristics of configuration, dimensions, tolerances and mass for moulded O-Ring seal elements, phosphate ester fluid resistant, for use as static seals in hydraulic systems for aerospace application. Application temperatu
10、re range: 55 C to 107 C of continuous operation. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest editio
11、n of the referenced document (including any amendments) applies. EN 6109, Aerospace series Static seal elements elastomer moulded, phosphate ester resistant Technical specification 1) EN 6111, Aerospace series Ethylene-propylene elastomer (EPM/EPDM) Hardness 80 IRHD for static seal elements in hydra
12、ulic systems for long-term application Material standard 1) EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts 3 Requirements 3.1 Configuration, dimensions, tolerances and mass Configuration shall be in accordance with Figure 1. Dimensions shall
13、 conform with Figure 1 and Table 1. Tolerances shall be in accordance with Table 1. Mass shall be in accordance with Table 1. Dimensions and tolerances are expressed in millimetres (inches). 3.2 Material Ethylene-propylene elastomer (EPM/EPDM) per EN 6111. 1) Published as ASD-STAN Prestandard at the
14、 date of publication of this standard. http:/www.asd-stan.org/ prEN 6075:2015 (E) 4 Figure 1 Configuration prEN 6075:2015 (E) 5 Table 1 O-Rings Diameter code, dimensions, tolerances and mass (1 of 9) Diameter code W ID Mass kg/1 000 pieces Tolerances Tolerances 10 % 001 1,02 (.040) 0,08 ( .003) 0,74
15、 (.029) 0,10 ( .004) 0,006 002 1,27 (.050) 1,07 (.042) 0,012 003 1,52 (.060) 1,42 (.056) 0,019 004 1,78 (.070) 1,78 (.070) 0,033 005 2,57 (.101) 0,13 ( .005) 0,040 006 2,90 (.114) 0,042 007 3,68 (.145) 0,051 008 4,47 (.176) 0,058 009 5,28 (.208) 0,066 010 6,07 (.239) 0,072 011 7,65 (.301) 0,087 012
16、9,25 (.364) 0,100 013 10,82 (.426) 0,115 014 12,42 (.489) 0,131 015 14,00 (.551) 0,145 016 15,60 (.614) 0,160 017 17,17 (.676) 0,173 018 18,77 (.739) 0,190 019 20,35 (.801) 0,15 ( .006) 0,202 020 21,95 (.864) 0,218 021 23,52 (.926) 0,232 022 25,12 (.989) 0,247 023 26,70 (1.051) 0,263 024 28,30 (1.11
17、4) 0,275 025 29,87 (1.176) 0,291 026 31,47 (1.239) 0,305 027 33,05 (1.301) 0,320 028 34,65 (1.364) 0,333 029 37,82 (1.489) 0,25 ( .010) 0,363 030 40,10 (1.614) 0,393 031 44,17 (1.739) 0,423 032 47,35 (1.864) 0,458 033 50,52 (1.989 0,480 034 53,70 (2.114) 0,510 035 56,87 (2.239 0,538 036 60,05 (2.364
18、) 0,567 037 63,22 (2.489) 0,596 038 66,40 (2.614) 0,627 039 69,57 (2.739) 0,38 ( .015) 0,656 040 72,75 (2.864) 0,685 041 75,92 (2.989) 0,713 042 82,27 (3.239) 0,771 prEN 6075:2015 (E) 6 Table 1 O-Rings Diameter code, dimensions, tolerances and mass (2 of 9) Diameter code W ID Mass kg/1 000 pieces To
19、lerances Tolerances 10 % 043 1,78 (.070) 0,08 ( .003) 88,62 (3.489) 0,38 ( .015) 0,830 044 94,97 (3.739) 0,889 045 101,32 (3.989) 0,948 046 107,67 (4.239) 1,005 047 114,02 (4.489) 1,063 048 120,37 (4.739) 1,121 049 126,72 (4.989) 0,58 ( .023) 1,181 050 133,07 (5.239) 1,238 102 2,62 (.103) 0,08 ( .00
20、3) 1,24 (.049) 0,13 ( .005) 0,078 103 2,06 (.081) 0,093 104 2,84 (.112) 0,108 105 3,63 (.143) 0,124 106 4,42 (.174) 0,141 107 5,23 (.206) 0,157 108 6,02 (.237) 0,172 109 7,59 (.299) 0,202 110 9,19 (.362) 0,235 111 11,53 (.424) 0,266 112 12,37 (.487) 0,297 113 13,94 (.549) 0,330 114 15,54 (.612) 0,36
21、0 115 17,12 (.674) 0,392 116 18,72 (.737) 0,425 117 20,29 (.799) 0,15 ( .006) 0,456 118 21,89 (.862) 0,489 119 23,47 (.924) 0,519 120 25,07 (.987) 0,550 121 26,64 (1.049) 0,583 122 28,24 (1.112) 0,613 123 29,82 (1.174) 0,644 124 31,42 (1.237) 0,677 125 32,99 (1.299) 0,707 126 34,59 (1.362) 0,739 127
22、 36,17 (1.424) 0,771 128 37,77 (1.487) 0,803 129 39,34 (1.549) 0,25 ( .010) 0,833 130 40,94 (1.612) 0,866 131 42,52 (1.674) 0,897 132 44,12 (1.737) 0,930 133 45,69 (1.799) 0,961 134 47,29 (1.862) 0,991 prEN 6075:2015 (E) 7 Table 1 O-Rings Diameter code, dimensions, tolerances and mass (3 of 9) Diame
23、ter code W ID Mass kg/1000 pieces Tolerances Tolerances 10 % 135 2,62 (.103) 0,08 ( .003) 48,90 (1.925) 0,25 ( .010) 1,024 136 50,47 (1.987) 1,055 137 52,07 (2.050) 1,088 138 53,64 (2.112) 1,118 139 55,25 (2.175) 1,150 140 56,82 (2.237) 1,183 141 58,42 (2.300) 1,214 142 59,99 (2.362) 1,244 143 61,60
24、 (2.425) 1,277 144 63,17 (2.487) 1,308 145 64,77 (2.550) 1,338 146 66,34 (2.612) 1,371 147 67,95 (2.675) 0,38 ( .015) 1,402 148 69,52 (2.737) 1,434 149 71,12 (2.800) 1,466 150 72,69 (2.862) 1,497 151 75,87 (2.987) 1,561 152 82,22 (3.237) 1,686 153 88,57 (3.487) 1,813 154 94,92 (3.737) 1,939 155 101,
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASDSTANPREN60752015AEROSPACESERIESSTATICSEALELEMENTSORINGETHYLENEPROPYLENEMOULDEDPHOSPHATEESTERRESISTANT55TO107INCHSERIESEDITIONP2PDF

链接地址:http://www.mydoc123.com/p-453692.html