ASD-STAN PREN 3682-004-2011 Aerospace series Connectors plug and receptacle electrical rectangular interchangeable insert type rack to panel operating temperature 150 continuous Pa.pdf

《ASD-STAN PREN 3682-004-2011 Aerospace series Connectors plug and receptacle electrical rectangular interchangeable insert type rack to panel operating temperature 150 continuous Pa.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 3682-004-2011 Aerospace series Connectors plug and receptacle electrical rectangular interchangeable insert type rack to panel operating temperature 150 continuous Pa.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 3682-004 Edition P 2 July 2011 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Supersedes editio

2、n P 1 of September 2002 and will supersede EN 3682-004:2006 Descriptors: ENGLISH VERSION Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 C continuous Part 004: Size 2 receptacle Product standard Srie aro

3、spatiale Connecteurs lectriques rectangulaires rackables, fiches et embases, inserts interchangeables, temprature dutilisation 150 C continu Partie 004 : Botier femelle taille 2 Norme de produit Luft- und Raumfahrt Elektrischer Rechtecksteckverbinder, freie und feste Bauform, auswechselbare Isolierk

4、rper, Gestell-Einschubsteckverbinder, Betriebstemperatur 150 C konstant Teil 004: Steckdose Gre 2 Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for

5、 the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically

6、 or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (

7、EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1 July 2011 Comments should be sent within six months after the date of

8、 publication to ASD-STAN Electrical Domain Copyright 2011 by ASD-STAN prEN 3682-004:2011 (E) 2 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Required characteristics.3 5 Designation 8 6 Marking .8 7 Technical specification .8 Foreword This standard was revie

9、wed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3682-004:2011 (E) 3 1 Scope This standard defi

10、nes the size 2 receptacle used in the family of rectangular electrical connectors for rack to panel, with interchangeable inserts. The plug corresponding to this receptacle is defined in EN 3682-005. 2 Normative references The following referenced documents are indispensable for the application of t

11、his document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3682-001, Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to p

12、anel, operating temperature 150 C continuous Part 001: Technical specification EN 3682-002, Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 C continuous Part 002: Specification of performance and contact

13、 arrangements EN 3682-005, Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 C continuous Part 005: Size 2 plug Product standard ISO 263, ISO inch screw threads General plan and selection for screws, bolts

14、 and nuts Diameter range 0,06 to 6 in 1)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3682-001 apply. 4 Required characteristics 4.1 Dimensions See Figures 1 to 3. Dimensions are in millimetres. 1) Published by: ISO International International Stand

15、ardisation Organisation http:/www.iso.ch/ prEN 3682-004:2011 (E) 4 Key 1 Axis of T , see note. diameter 3,96 2 18 holes diameter 3,71 3 Axis of S , see note. NOTE See EN 3682-001, Tables 2, 3 and 4 for S and T references. Figure 1 prEN 3682-004:2011 (E) 5 aFor arrangements with size 22 contacts. bFo

16、r arrangements without size 22 contacts. Figure 2 prEN 3682-004:2011 (E) 6 Key 1 Eight Philips screw 4-40 UNC 2A 2 Cavities identification on the front and the rear of the flange 3 Insert retention device 4 Marking of trademark of manufacture and part number on right or left of the flange aSee ISO 2

17、63. NOTE See EN 3682-001, Tables 2, 3 and 5 for S and T references. Figure 3 prEN 3682-004:2011 (E) 7 4.2 Recommended panel cut-out and mounting of connectors See Figure 4. Dimensions in millimetres Key diameter 4,58 1 18 holes diameter 4,22 NOTE The W reference represents the width of the equipment

18、. Figure 4 prEN 3682-004:2011 (E) 8 5 Designation EXAMPLE Description block ELECTRICAL CONNECTOR, SIZE 2 RECEPTACLE Identity block EN 3682 R 2 200 A 01 L Standard reference Housing Type (R = Receptacle, P = Plug) Housing size Connector insert combination code (see EN 3682-002) A: coaxial, triaxial a

19、nd quadrax contacts not connected to the ground Polarization (see EN 3682-002) Contact delivery If left blank: insert delivered with contacts exept coaxial, triaxial and quadrax contacts; L: insert delivered without contacts. 6 Marking Housing identification marking, as specified in Clause 5, should be applied in the position shown on the corresponding drawing. When polarization code is 00, the polarization code is not included in the connector marking. In addition, marking shall show: date of manufacture (year week); manufacturer name or trademark. 7 Technical specification See EN 3682-001.