ARMY MIL-S-63433 D-1989 SIMULATOR ARTILLERY FLASH M21 PERFORMANCE SPECIFICATION FOR《M21型炮兵闪光模拟器的规范》.pdf

《ARMY MIL-S-63433 D-1989 SIMULATOR ARTILLERY FLASH M21 PERFORMANCE SPECIFICATION FOR《M21型炮兵闪光模拟器的规范》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-63433 D-1989 SIMULATOR ARTILLERY FLASH M21 PERFORMANCE SPECIFICATION FOR《M21型炮兵闪光模拟器的规范》.pdf（43页珍藏版）》请在麦多课文档分享上搜索。

1、 I INCH-POUND I MIL-S-63433D (AR) 20 January i989 SUPERSEDING MIL-S-63 433C (AR) 24 April 1987 MIL I TARY SPEC IF I CAT I ON SIMULATOR, ARTILLERY FLASH; M21, PEREORMANCd SPECIFICATION FOR This specification is approved for use within the U.S. Army Armament, Munitions and Chemical Coininand, and is a

2、vailable for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scose. This specification covers requirements for design and establishes a uniform method of testing one type of Artillery Flash Simulator, M21. The purpose of testing is to determine performance, safety, sou

3、ndness of design and resistance to environments encountered during storage, handling, and service use. . 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 SpeciEications and standards. The following sDecifications and standards form a part of this specification to the extent specified herein.

4、Unless-otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS MILITARY MIL-P-116 MIL-A- 25 50 MIL-A-48078 - Preservation - Pack

5、aging, Methods Of. - Ammuni tion and Special Weapons; General Specification For. - Ammunition, Standard Quality Assurance Provisions, General Specification For. Beneficial comments (recommcndations, additions, deletions) and any pertinent data which may be of use in improving this document should be

6、 addressed to: Commander, U.S. Army Armament, Munitions, and Chemical Command, Ath. AMSMGQA, Picatinny Arsenal, New Jersey 07806-5000 by using the self-addressed Standardization Document Improvement Proposai (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FsC 1370 DISTRIB

7、UTION STATEMENT A, Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS f-3 PAGES. - - - c Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-63433D (AR) STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for

8、 MIL-STD-109 - Quality Assurance Terms and Definitions. MIE-STD-331 - Fuze and Fuze Components, Environmental MIL-STD-810 - Environmental Test Methods. MIL-STD-889 - Dissimilar Metals. , Inspection by Attributes. and Performance Tests for. (Unless otherwise indicated, copies of federal and military

9、specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein.

10、Unless otherwise specified, the issues shall be those in effect-on the. date of the solicitation. 2.1.2 Other Government documents, drawings, and publications. DRAWINGS U.S. ARMY ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER (ARDEC ) 9342970 - Packing processing, and testing of the completed

11、 item and related hazardous materials. All required safety information shall be submitted to the Contracting Officer for approval. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-63933D 13 E 7777706 0350307 7 E NIL-S-6 3 4 3 3D (AR) 3.2.5.1 S

12、imulator explosive hazard classification. A copy of the DOT authorization shall be furnished to the Contracting Officer prior to delivery of any assemblies, items, or hazardous materials. Transportation of the item must meet the requirements of the CODE OF FEDERAL REGULATIONS TITLE 49 - TRANSPORTATI

13、ON, PARTS 100-199. .The simulator, in its shipping and storage packaging, shall meet the requirements of the following classifications when tested in accordance with 5.3.f “Stack Test“ and 5.3.9 “External Fire Stack Test“ of TB 700-2: DoD Hazard Classification - 1.3 DoD Compatability Group - G DOT H

14、azard Classification - Class B Exslosives DOT Narking - SPECIAL FIREWORKS - HANDLE CAREFULLY - KEEP FIRE AWAY Prior to the acceptance of the simulator by the Government, the Contracting Officer shall review the contractors baseline Tech Data Package to determine if this classification can be obtaine

15、d by analogy or if testing in accordance with TB 700-2 is required. 3.2.5.2 DOT authorization/hazard classification. -I-_- Certification from tG susplier shall be required to assure no significant change in the item, materials, packaging, etc. which would affect the DOT autharization/hazard classifi

16、cation. 3.2.5.3 Hazardous materials (energetic, toxic, carcinogenic). _I- -_1_- - Hazardous materials/components will be identified as .they are selected, and submitted- to the Contracting Officer for aiproval. Only energetic materials acceptable for DOD use will be utilized. 3.2.5.4 Explosive ordna

17、nce disposal (EOD). EOD render saEe procedures and applicable render safe procedure tools will bcs formulated as early as possible and will be kept current with design. These procedures and tools shall be made available to the Government for approval as early as possible to insure applicable tools,

18、equipment and publications will be available to army EOD units 30 days before the deployment date of the siinulator. 3.2.5.5 Demilitarization. Demili%arization/dispocal procedores will be formulated and kept current with design changes as they ara instituted. These procedures shall. be made availabl

19、e to the Government for approval at the time of submission of the first ar ticle sample. 3.2.5.6 Static and other induced electric hazards. The ignition system should be designed and maintained so that static _ charges and induced electric energies will not produce a hazardous device. 3.2.5.6.1 Elec

20、tromagnetictibility. The simulator shall not function when tested as specified in 4.5.14. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-S-b3i33D 33 777770b 0350330 5 - MIL-S-63433D (AR) 3.2.5.6.2 Electrostatic discharge (ESD). The simulator

21、shall not function from human-borne or aircraft-borne ESD when tested as specified in 4.5.15. shall be esigned and constructed to conform to the performance requirements specified herein. from either plastic, paper or both products with exception of the connecting wires, contacts and pyrotechnic com

22、positions. The components of the simulator shall consist of at least a container, flash charge, igniter, connecting wires and plug assemblyand some method of protecting the item from inadvertant or accidental initiation. 3.3 Design and construction. The components o the simulator 3.3.1 Assembly of c

23、omponents. All components shall be made 3.3.2 Application of sealants and adhesives. Any sealants or adhesives used in the construction of the simulator shall be applied in such a manner that the performance of the simulator in 3.4 after prolonged storage shall not be degraded by aging or any other

24、changes of the sealant or adhesive. A sealant used toseal the interface of a cap and container shall be applied in such a manner that excessive sealant will not enter the interior of the simulator and cover or encapsulate the chemical components in such a way as to change the functional characterist

25、ics of the simulator under . prolonged storage. 3.3.3 Plastic parts. Plastic components shall be compatible with the flash charge and shall not degrade during prolonged storage to the extent that the simulators fail to meet the functioning requirements of 3.4. 3.3.4 Moisture content. 3.3.4.1 Charge

26、composition. The moisture content of the charge composition at the loading station at the time of loading shall not exceed 0.10 percent when tested as specified in 4.5.3.1. 3.3.4.2 Paper and paper products. The moisture content of any paper or paper product component of the simulator assembly at the

27、 loading station at the time of loading shall not exceed 6.0 percent when tested as specified in 4.5.3.2. 3.3.5 Bridge-wire resistance. The igniter bridge-wire resistance shall be between 1.1 and 1.4 ohms when tested as specified in 4.5.9. 3.3.6 Connecting wire assembly resistance. The connecting wi

28、res shall be 24.6 + .4 inches in length fitted with a plug that interfaces with the applicable gunfire devices. resistance, including connecting wires, bridgewire and plug shall be 1.51 ohms max. when tested as specified in 4.5.13. The assembly 6 Provided by IHSNot for ResaleNo reproduction or netwo

29、rking permitted without license from IHS-,-,-MIL-S-63q33D 13 7777706 0350311 7 3.3.7 Shorting cap. cap for safety purposes. 3.3.8 Label. The la MI L-S - 6 3 4 3 3D (AR) The plug shall be fitted with a shorting el shall be as shown in Figure 1. 3.4 Performance. The simulator shall not damage the gunf

30、ire device or interface with repeated use, and shall satisfy all requirements specified herein after subjection to the applicable environmental tests. Performance shall be measured and values recorded in accordance with 6.4 for the ballistic operation of the simulator. 3.4.1 Fun-ctioning. The assemb

31、ly shall function and comply with all requirements when tested iii accordance with 4.5.4 after conditioning at the specified temperatures. 3.4.1.1 Sound characteristics. The sound level intensity of the simulatorshall be a minimum of 124 decibels (db) to a maximum (max.) of 147 db when measured at a

32、 distance of 96 meters min. from the item under test when tested as specified in 4.5.4.1. 3.4.1.2 Functioning time. The time from application of 24 + 2 Volts Direct Current (VDC), with a minimum ignition enerqy of 3.0 milliwatt seconds/ohm, to initiation of the assembly shaii not be greater than .50

33、 seconds (sec) when tested as specified in 4.5.4.2. 3.4.1.3 Flash characteristics. The flash intensity of the simulator shall be 4 x 100 candlepower minimum when tested as specified in 4.5.4.3. Residual smoke shall be white in appearance. 3.4.2 Chamber withdrawal. The simulators shall be capable of

34、being extracted freely from the firing tubes of approved gunfire devices when a force of three (3) to twelve (12) pounds is applied at a temperature of 70+5OF - when tested as specified in 4.5.2. 3.4.3 the electric igniter. The continuity of the electric igniter shall be 10 milliseconds (ms) minimum

35、 at 12 VDC (nominal) at O. 5 amperes (amp). It shall produce an open circuit (if only for an instant) within 25 ms of receiving 12 VDC at 1 ampere when tested as specified in 4.5.10. 3.4.4 Surface danger zone. When fired, the simulator shall produce a hazardous fragment distance of no greater than 2

36、5 meters to either side or 5Q meters forward of the firing device when tested as specified in 4-.5.12. 3.4.5 Performance reliability, The simulator must meet all performance requirements at a reliability of not less than 95 percent at a confidence level of 90 percent over a temperature range of 125

37、5 50F to minus 25 + 50F as defined in 4.3.3 and 4.4.2. - 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-b3433D 13 W 777770b 0350332 7 U MIL-S-63433D (AR) DANGER: DO NOT CUT OR BREAK I OPEN TO REMOVE EXPLOSIVE NOTE 3 CONTENTS. SERIOUS INJURY

38、CAN I RESULT THROUGH IMPADPER USE. 5 I MULATOR, ART i LLERV FLASH: M21 SAFETY INSTRUCTIONS BEFORE LOADING OR UNLOADING SIMULATOR FROM FIRING FIXTURE ALL POWER SWITCHES MUST BE OFF. GRASP FRAME OF FIRING FIXTURE TO DISCHARGE STATIC ELECTRICITY. SHORT CIRCUIT CAP MUST REMAIN ON ELECTRICAL PLUG UNTIL R

39、EADY TO CONNECT SIMULATOR TO FIRING FIXTURE. REPLACE SHORT CIRCUIT CAP ON ALL UNUSED SIMULATORS AND DUDS PRIOR TO REMOVAL FROM FIRING FIXTURE. HAZARQ: DO NOT STAND IFJ FRONT OR-ABOVE FIRING FIXTURE AT ANY TIME. NQTE 3 NDTES: 1. PRINTED INFDRMATION SHALL BE WATER AND SMUDGE 2. ADHESIVE SHALL PASS WAT

40、ER IMMERSION TEST. 3. PRINT WITH RED INK. 4. PRINT REMAINDER WITH BLACK INK. 5. INSERT LOT NUMBER, RES I STANT. Figure 1 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S- 6 3 43 3D (AR) 3.5 Environmental conditions. 3.5.1 Vibration. The simula

41、tors, when packed, shall not fire when subjected to vibration as specified in 4.5.8.1. After vibration (and additional testing as indicated for first article tests), the simulators shall show no signs of damage, shall be safe to handle and operate, and shall meet the performance requirements of 3.4.

42、1. 3.5.2 Five foot drop. The bare simulator shall not fire when dropped from a height of 5 feet as specified in 4.5.8.12. After drop, the simulator shall be safe to handle and operate, and shall meet the applicable requirements of 3.4.1. 3.5.3 Seven-foot drop. The simulators, when packed, shall not

43、fire when subjected to 7 foot drop as specified in 4.5.8.6. After being subjected to drop test (and additional testing as indicated for first article tests), the simulators shall show no signs of damage, shall be safe to handle and operate, and shall meet the performance requirements of 3.4.1. 3.5.4

44、 Loose cargo. The simulators, when packed, shall not fire when subjected to loose cargo testing as specified in 4.5.8.8. After loose cargo test (and additional testing as indicated for first article tests and quality conformance inspection), the simulators shall show no signs of damage, shall be saf

45、e to handle and operate, and shall meet the performance requirements of 3.4.1. 3.5.5 Ten foot drop. The bare simulator shall not fire when dropped from a height of i0 feet as specified in 4.5.8.5. After being subjected to drop, the simulators, if not damaged to the extent that they cannot be loaded

46、into the gunfire device shall be safe to operate. If after such a drop, the simulators are damaged to the extent that they cannot be loaded into the gunfire device, they shall be safe to handle and dispose of. 3.5.6 Forty-foot drop. The simulators, when packed, shall not detonate when dropped from a

47、 height of 40 feet as specified in 4.5.8.7 and shall be safe to handle and dispose of. 3.5.7 Cold temperature. The bare simulator shall be capable of meeting the performance requirements of 3.4.1 after being subjected to cold temperature conditions as specified in 4.5.8.2. 3.5.8 Hottemperature. The

48、bare simulator shall be capable of meeting the performance requirements of 3.4.1 after being subjected to hot temperature conditions as specified in 4.5.8.3. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 MIL-S-63LI33D 33 W 7779706 0350334 2 MF

49、MIL-S-63433D (AR) 3.5.9 Leakage test. The simulators, when packaged, shall be -I- capable of meeting the performance requirements o 3.4.1 after exposure to the leakage test as specified in 4.5.6. 3.5.10 Water _- immersion test. The bare simulator shall meet the performance requirements o 3.4.1 after exposure to water immersion as specified in 4.5.8.11. 3.5.11 Jumble. The bare simulator shall comply with the fol