ARMY MIL-S-44220 A-1989 SLEEPING BAG COLD WEATHER AIRCRAFT SURVIVAL KIT (VACUUM PACKED)《冬季飞机救生装置睡袋(真空包装)》.pdf

《ARMY MIL-S-44220 A-1989 SLEEPING BAG COLD WEATHER AIRCRAFT SURVIVAL KIT (VACUUM PACKED)《冬季飞机救生装置睡袋(真空包装)》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-44220 A-1989 SLEEPING BAG COLD WEATHER AIRCRAFT SURVIVAL KIT (VACUUM PACKED)《冬季飞机救生装置睡袋(真空包装)》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、;5 MIL-S-44220A BY W 7997706 040LY70 7 W Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick., MA 01760-5014 by using the self-

2、 addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. MIL -S -44220 A( GL) 16 June 1989 SUPERSEDING MIL -S -4 4 2 2 O ( GL ) 31 March 1986 MILITARY SPECIFICATION SLEEPING BAG, COLD WEATHER AIRCRAFT SURVIVAL KIT (VACUUM PACKED) Thi

3、s specification is approved for use by the Natick Research, Development, and Engineering Center, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a vacuum packed sleeping bag of one type and s

4、ize for use in survival kits in aircraft operating in cold climates. * 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwis

5、e specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FE DE RAL V-F-106 - Fasteners, Slide, Interlocking DDD-L-20 - Label: For Cl

6、othing, Equipage, and Tentage, PPP-B-636 - Boxes, Shipping, Fiberboard (General Use Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-44220A 84 7777706 0401471 O M MIL -S -4 4 220 A( GL MILITARY MIL-C-5040 - Cord , Fibrous,Nylon MIL-L-35078 - Loa

7、ds , Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For MIL-F-43097 - Feathers and Down , Waterfowl; TAN-O-QUIL-QM Treated MIL-T-43548 - Thread , Polyester Core: Cotton- , Rayon- , or Pol ye st e r-Covered STANDARDS FEDERAL FED

8、-STD-595 - Colors FED-STD-751 - Stitches , Seams , and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members For Containers and Pallets MIL

9、-STD-810 - Environmental Test Methods and Engineering Guidelines (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center , ( ATTN : NPODS) , 5801 Tabor Avenue , Philadelphia , PA 1 9120 -5099. 2.2

10、 Non-Government publications. The following document forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issu

11、es of- documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Mat

12、erials, 1916 Race Street , Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2 Provided

13、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-S-44220A 84 7777706 0401472 2 W a O e MILS -44220A( GL) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document take

14、s precedence. regulations unless a specific exemption has been obtained. Nothing in this document, however, supersedes applicable laws and 3. REQUIREMENTS 3.1 First article. When specified (see 6.21, a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Guide

15、sample. Samples of the sleeping bag only (not vacuum packed), when furnished, are solely for guidance and information to the contractor (see 6.4). Variation from this document may appear in the sample, in which case this document shall govern. * 3.3 Material. It is encouraged that recycled material

16、be used when practical as long as it meets the requirements of this document. 3.3.1 Shell fabric. The inner and outer shell fabric shall be 1.9 ounces - + 0.2 ounce per yard ripstop, 70 denier nylon fabric woven with 109 yarns per inch minimum in the warp direction and 99 yarns per inch minimum in t

17、he filling direction. There shall be a minimum of five repeat yarns per inch of the reinforcing ribs in both the warp and filling directions. The material shall be wat er-repe 1 lent treated . 3.3.2 Baffling material. The baffling material shall be a 1 + 0.1 ounce per square yard, 20 denier, single-

18、warp-knit stitch tricot knit fabrFc with 190 yarns per inch minimum in the warp direction and 32 yarns per inch width in the filling direction. * 3.3.3 Slide fastener. The slide fastener shall be size MHS, type III, style 1, nylon or polyester continuous element fastener and shall meet all the requi

19、rements of V-F-106. slider with wire stirrup pulls and thongs attached, and the slider shall be free running for emergency exit. width and water-repellent treated. The length of the slide fastener shall be a minimum of 65 inches, and all slider stops, tape, and chain components shall be black. The f

20、astener shall have a reversible double-pull The slide fastener tape shall be 1 2 1/16 inch 3.3.4 Cord, nylon. The nylon drawcord shall conform to type II of MIL-C-5040. The color shall be black. 3.3.5 Clamp, cord, plastic. The cord clamp shall consist of a lock body and lock wheel. equal, and the lo

21、ck wheel shall conform to Fastex No. 238-082051-00-0101 or equal. The color shall be black. The lock body shall conform to Fastex No. 238-390703-00-5612 or I 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL -S-44220A( GL) 3.3.6 Thread. The threa

22、d for seaming and stitching shall be No. 50, 2 ply, conforming to MIL-T-43548. 3.3.7 - Down. The down shall conform to type II, class 1 of MIL-F-43097, except that the TAN-O-QUIL-QM treatment and all related requirements and related inspection provisions need not apply. 3.3.8 Instruction sheets. The

23、 user instructions shall be legibly printed on two 8-1/2 by 11 inch white, bond paper sheets. The contents of each instruction sheet for opening and use shall be in accordance with figures 1 and 2 of this document. * 3.3.8.1 Identification marking. Identification marking shall be placed in the upper

24、 left hand corner of the label shown on figure 1 of this document. This identification marking shall conform to class 5 of DDD-L-20. 3.4 Design. The sleeping bag shall be a mummy bag with a slide fastener closure and integral hood with drawstring closure with quick release for hood closure and be do

25、wn filled. 3.5 Color. The color of the sleeping bag shall conform to International Orange No. 12246 of FED-STD-595. e 3.6 Construction. The sleeping bag shall be differential-cut construction with all baffling seams, both internal and external, turned and finished toward the inside. I 3.6.1 Insulati

26、on distribution. The sleeping bag shall be down insulated with the down evenly distributed throughout the bag with each channel (as formed.by the baffling) containing equal and proportionate amounts of the total amount of down (see 6.6). 3.6.2 Stitches, seams, and stitching. Stitches, seams, and sti

27、tching shall conform to FED-STD-751. Stitch type shall be 301; seam type shall be SSa-1; and stitches per inch shall be 8-10. 3.6.2.1 Type 301 stitching. Ends of all stitching shall be backstitched or overstitched 1/2 inch minimum, except when caught in other stitching or turned under in a hem. Thre

28、ad tensions shall be maintained so that there will be no loose stitching resulting in loose bobbin or top thread, or excessively tight stitching resulting in puckering of the materials sewn. The lock shall be embedded in the materials sewn. 3.6.2.1.1 Repairs of type 301 stitching. Repairs of type 30

29、1 stitching shall be as follows: a. When thread breaks or bobbin run-outs,occur during sewing, the stitching shall be repaired by restarting the stitching a minimum of 1/2 inch back of the end of the stitching. - 1/ 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

30、se from IHS-,-,-T e O - MIL-S-44220A 84 m 9999906 OLIO1474 b m MIL -44220A( GL) b. Thread breaks or two or more consecutive skipped or run-off stitches noted during inspection of the item (in-process or end item) shall be repaired by overstitching. the defective area, and continue a minimum of 1/2 i

31、nch beyond the defective area on to the existing stitching. be repaired by removing the defective stitching, without damaging the materials, and restitching in the required manner. - 1/ The stitching shall start a minimum of 1/2 inch in back of Loose or excessively tight stitching shall - I/ When ma

32、king the above repairs the ends of the stitching are not required to be backstitched. 3.6.2.2 Trimming. All thread ends shall be trimmed to a maximum length of 1 inch. * 3.7 Use of automated equipment. Automated equipment may be used to perform any of the operations specified, providing that the sea

33、m and stitch type areas specified and the finished component conforms to the required configurations. * 3.8 Finished measurements. The measurements of the finished sleeping bag shall be a minimum of 91 inches long by 32 inches wide at the widest point and 22 inches wide at the narrowest point. The d

34、imensions shall be taken on the outside of the bag. The length shall be taken from the foot to the top of the hood in the .open position. the slide fastener closed and the bag laid out flat. The width shall be taken at the widest point with 3.9 Vacuum packing. The sleeping bag shall be vacuum packed

35、 in two layers of a heat-sealable transparent film. Each layer of the film shall be fitted with a pull tab for easy opening. Both pull tabs shall be on the same side of the package. The vacuum packed sleeping bag shall be capable of passing the vibration, altitude, low temperature and ease of openin

36、g tests specified in 4.5.1, 4.5.2, and 4.5.3. bag shall be 13 by 13 by 2-1/2 inches. The instruction sheet for opening the package (figure 1) shall be placed between the two layers of film on the same side as the pull tabs so as to be readable before opening. The instructions for use (figure 2) shal

37、l be placed between-the two layers of film on the side opposite the pull tabs. The maximum dimensions of the vacuum packed sleeping 3.10 Insulating liclol value. After removal from the vacuum packing, the sleeping bag shall have a test sample average liclof value of 7.1 with no individual irclf valu

38、e of less than 6.8 when tested as specified in 4.5.4. 3.11 Workmanship. The finished sleeping bag shall conform to the quality of product established by this document and the occurrence of defects shall show any sign of loss of vacuum. . not exceed the applicable acceptable quality levels. Vacuum pa

39、cking shall not 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-S-44220A 84 m 7779706 0401475 m MIL-S-4422OA(GL) 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, t

40、he contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection require

41、ments specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for c

42、ompliance. All items shall meet all requirements of sections 3 and 5. become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or

43、 supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, ei

44、ther indicated or actual, nor does it commit the Government to accept defective material. * 4.1.2 Responsibility for dimensional requirements. Unless otherwise The inspection set forth in this specification shall specified in the contract or purchase order, the contractor is responsible for ensuring

45、 that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to assure compliance with all dimensional requirements. 4.1.3 Certificates of compliance. When certificates

46、 of compliance are submitted, the Government reserves the right to inspect such items to determine the validity of the certification. 4.2 Classification of inspections. The inspection requirements specified herein. are classified as follows: a. First article inspection (see 4.3). b. Quality conforma

47、nce inspection (see 4.4). 4.3 First article inspection. When a first article is required (see 3.1 and 6.21, it shall be examined for the defects specified in 4.4.3 and 4,4.4 and tested as specified in 4.4.5. rejection of the first article. The presence of any defect shall be cause for 4.4 Quality co

48、nformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL S-44220A( GL) 4.4* 1 Component and material inspection. In accordance w

49、ith 4.1, components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. 4.4.1.1 Component and material certification. A certificate of compliance may be acceptable as evidence that the component and material conforms to the requirements specified in 3.3.1 and 3.3.2. Each certificate of complian