ARMY MIL-S-44110 B-1991 SLACKS MATERNITY UTILITY WORK UNIFORM《公用工作服孕妇长裤》.pdf

《ARMY MIL-S-44110 B-1991 SLACKS MATERNITY UTILITY WORK UNIFORM《公用工作服孕妇长裤》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-44110 B-1991 SLACKS MATERNITY UTILITY WORK UNIFORM《公用工作服孕妇长裤》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-44LLOB 84 m 999990b 0468760 L m Xi L- S -4 4 I 1 OB 10 January 1991 SUPERSEDING KCL-S-44110A 21 April 1987 MILITARY SPECIFICATIOK SLACKS, MATERWITY, UTILITY WORK UNIFORM This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. Thi

2、s specification covers maternity slacks made of cotton poplin cloth, woodland camouflage pattern. 1.2 Classification, The slacks shall be one of the following sizes (see 6.2): Schedule of sizes Short Regular Long 6 6 6 8 8 8 !O 10 10 12 12 12 14 14 14 16 16 16 18 18 18 20 2c) 22 22 20 22 Beneficial

3、comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: U.S. Army Natiek Research, Development, and Engineering Center, Ilatick, MA 01760-5019 by using the Standardization Document Improvement Proposal (DD Form 1426

4、) appearing at the end of this document or by letter. AMSC N/A FSC 8410 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-4YLLOB 84 M 99999Ob 04b87bL 3 2.1 Governme

5、nt documents. 2.1.1 Specifications, standards and handbooks, The folluwing specifications, s,a.i:i;s and handbooks form n part af.th1s documeiit LLI; the esteilt specifiez herein. Cnless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Ind

6、ex of Specifications and Standards (DODISS) and supplement thereto, cited iI? the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-203 - Paper, Kraft, Untreated A-A-50198 - Thread, Gimp, Cotton, Buttonhole A-A-50199 - Thread, Polyester Core: Cotton- or Polyester-Covered V-B-871 - Button, Sewing Ho

7、le, and Button Staple (Plastic) DDD-L-2 O - Label: For Clothing, Equipage, and Tentage PPP-B-636 - Boxes, Shipping, Fiberboard (General Use) MILITARY MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For Cotto

8、n ML-C-43468 - Cloth, Camouflage Pattern; Wind Resistant Poplin, STANDARDS FEDERAL FED-STD-191 - Textile Test Methods FED-STD-595 - Colors Used in Government Procurement FED-STD-751 - Stitches, Seams, and Stitchings HLITARY MIL-STD-105 - Samplin Procedures and Tables for Inspection MIL-STD-129 - Mar

9、king for Shipment and Storage PIIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk. Buildin

10、g 4D, 700 Robbins Averiue, Philadelphia, PA 19111-5094.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-44LLOB 84 W 9777906 OYb87b2 5 7.2 Kan-Government pub?ications. The following documents form a part of this document to the extent specifi

11、ed herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Enless otherwise specified, the issues of documents not listed in tke DODISS are the issues of the documents cited in the sa:i:;ta:;an (see

12、6.2). AhfERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) Photographic Replica fo Seams (Application for copies should be addressed to the American Association of Textile Chemists and Colorists, Research Triangle Park, P.0, Box 12215, Durham, NC 27709.) AMERICAN SOCIETY FOR TESTING AND M

13、ATERIALS (ASTM) D 3951 - Standard Practice for Cownercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) THE COLOR ASSOCIATION OF THE UNITED STATES Standard Color Card of America Department of D

14、efense Standard Color Card ?or Sewing Threads Department of Defense Standard Shades for Buttons (Application for color cards should be addressed to-the Color Association of the United States, 343 Lexington Avenue, New York, NY 10016-0927. If color cards are not available from the Color Association,

15、individual color samples may be obtained fiom the contracting activity or as directed by the contracting activity.) (Non-Government standards and other publications are normally available from organizations that prepare or distribute the documents. These documents also may be available in or throtig

16、h libraries or other informational services. 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document however, supersedes applicable laws and regulations unless a specif

17、ic exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.21, a sample shall be subjected to first article inspection (see .3) in accordance with 4.3. B 3 ., Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-44LLOB

18、84 9999906 0468763 7 W 3.2 Guide sample. Guide samples, h c U O c IL O E o. L. :E Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-O O u) u. O u) I I Q- I O I O 4 O Cu7 4 u)n 4 I O 4 - 4 +I W4Q c ovo O cc v a,a, - O ci a, V id w Li P id w -a C idQ m L

19、im a, CUY 3 4 x W r d t z 3 L3 u v 3 W J 5 m i YI t U o. U o z c c 0 - (2 W 3 3 h E Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-44LLOB 84 m 9999906 0468774 1 m 3.13 Finished measurements. The finished meascrements shall be as shown in table

20、 II. inseam shall be t 3/4 inch. Ail tolerances shall be - 1/2 inch, except that the toierance for the TABLE 1. Finished measurements (inche* 6 8 10 12 14 16 18 20 22 1/2 Waist 11-3/4 12-1/4 12-3/4 13-1/2 14-1/4 15 16 17 18 relaxed - i/ 1/2 Hip - 2/ 19-3/4 20-1/4 20-3/4 21-1/2 22-1/4 23 24 25 26 uts

21、eam - 3/: Short 42-1/4 42-1/2 42-3/4 43 Regular 44-1/2 44-3/4 45 45-1/4 Long 46-1/2 46-3/4 47 47-1/4 Inseam - 4/: Short 32 32 32 32 Regular 33-1/2 33-1/2 33-1/2 33-1/2 Long 35 35 35 35 43-1/4 43-1/2 43-3/4 44 47-1/2 47-3/4 48 48-1/4 45-1/2 45-3/4 46 46-1/4 32 32 32 32 33-1/2 33-1/2 33-1/2 33-1/2 35

22、35 35 35 44:1/2 46-1/2 48-1/2 32 33-1/2 35 Taken from folded edge to folded edge at center of waistband in relaxed pos it ion. Taken from folded edge to folded edge of slacks along bottom of stretch pane 1. Taken from top of waistband along seam to bottom of slacks. Taken from crotch seam along inse

23、am to bottom of slacks. 11 Workmanship. The end item shall conform to the quality of product established by this specification and the occurrence of defects shall not exceed the applicable acceptable quality levels and point values. 4. QUALITY ASSLJRANCE PROVISIONS 4.1 Responsibility for inspection.

24、 Unless otherwise specified in the contract or purchase order, the contractor is responsible or the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other fa

25、cilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-44LLOB 84 m 9999906 04b8775 3 m YTL-S- i i OS -. :ne Government rese

26、rves the right to perform any of the inspections set forth iii nis specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all requirements 25 se:,iuns 3 and 5. The inspecti

27、on set forth in :his specification shall become a part of the contractirs overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Go

28、v-ernment for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor d

29、oes it commit the Government to accept defective material. 4.1.2 Responsibility for dimensional requirements. Unless otherwise speci- fied in the contract or purchase order, the contractor is responsible for ensuring that all specified dimensions have been met, When dimensions cannot be examined on

30、the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to ensure compliance with all dimensional requirements, 4.1.3 Certificates of compliance. Nhere certificates of compliance are sub- mitted, the Government reserves the right to inspect such i

31、tems to determine the validity of the certification. 4.2 Classification of inspections, The inspec.tion requirements specified herein are classified as follows: a. First article inspection (see 4.3). b, Qual i ty conformance inspection (see 4.41, 4.3 First article. When a first article is required (

32、see 3.1 and 6.2), it shall be examined for the defects specified in 4.4.2.1 and 4,4.2.2. 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection. In accordance with 4.1, compone

33、nts and materials shall be inspected in accordance with all the requireme-nts of referenced documents unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document, provisions contained in subsidiary specifications, testing shall be performed on the

34、 component listed in table III for characteristics noted. indicated, testing shall be conducted in accordance with FED-STD-191. All test reports shall contain the individual values utilized in expressing the final result, The lot shall be unacceptable if one or more sample units fail to meet any of

35、the test requirements specified. The lot size and sample size shall be in accordance with the following: In addition to testing Unless otherwise 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-44LLOB 84 9999906 0468776 5 Lot size yards Sampl

36、e size (sample units) 800 cr less 2 801 up to and including 22,000 3 22,OU: and aver 5 The sample unit shall be 2 yards full width of the nylon stretch cloth. TABLE III. Component tests - Requirement Component Character is tic paragraph Test method Nylon stretch cloth Material identification 3;3,2 -

37、 i/ Weight 3.3.2 5041 Texture 3.3.2 5070 Stretch (percent): Lengthwise 3.3.2 - 2/ Wid thw i se 3.3.2 - 21 PH 3.3.2 2811 Dimensional stability 3.3.2 5556 3/ . Bursting strength 3.3.2 5120 - 4/ Co lorf as tnes s to : Laundering 3.3.2.2 5610 Crocking 3.3.2.2 565 1 Perspiration 3.3.2.2 5680 - i/ A certi

38、ficate of compliance shall be submitted and will be acceptable for the stated requirement. Stretch of the cloth shall be measured an an Fnclined plane type of machine (IP4 or similar type) with a suitable autographic recording device. Five 4- by 6-inch specimens shall be cut from the sample unit wit

39、h the long direc- tion of the specimens parallel tc the direction to be tested. The five specimens shall be cut such that no two specimens contain the same wales or courses. One-inch clamps, placed 2 inches apart shall be used with the specimen placed in the clamp jaws without tension or slack. The

40、machine shall run through ten complete cycles, proceeding to its maximum depression so as to exert a 5-pound tension. Individual recorded stretch graphs shall - - 2, 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-44LLOB 84 = 999990b 0468777

41、 7 be used for each of the five specimens. The stretch of each specimen shall be measured at the peak of last recorded cycle, in a line perpendicular to the horizontal zero axis. The percent stretch for each specimen shall be calculated as follows: percent = Elongation dimensisn - Original dimension

42、 100 Original dimension The stretch of the sample unit shall be the average of the results obtained from the five specimens tested and shall be reported to the nearest 1 percent. - 3/ The cotton laundering procedure shall be followed. - 4/ It may be necessary to clamp the 1 x 1 rib material in a pre

43、stretched state before testing. 4.4.1.1 Component and material certification. A certificate of compliance may be acceptable as evidence that the waistband stabilizer conforms to the requirements specified in 3.3.3. 4.4.2 Point count inspection (see 6.5), 4.4.2.1 End item visual examination. The end

44、item shall be examined for the defects listed in table IV and the assessment of penalty points shall be as indicated therein. Sampling and acceptance criteria shall be as specified in 4.4.2.1.1. TABLE IV. End item visual defects Defect Point value I. MATERIAL DEFECT AND DAMAGE a. Any hole, cut, tear

45、, smash, burn, drill hole A/, scorched area, multiple float, or open place: 1. On outside (longest dimension in any direction): (a) - up to 1/4 inch inclusive (b) - more than 1/4 inch (a) - up to 1/4 inch inclusive (b) - more than 1/4 inch 2. On inside (longest dimension in any direction): b. Knot o

46、r club c. Misweave, area of poor dye penetration, dyestreak, broken and missing section of yarn, visible mend, thin place, or shade bar (largest dimension in any direction) d. Loose yarn or coarse yarn on outside e. Woven in waste on outside 2 3 1 2 1 Provided by IHSNot for ResaleNo reproduction or

47、networking permitted without license from IHS-,-,-NIL-S-44LLOB 84 9999906 0468778 9 ?Ii-S-44110E TABLE IV. End item visual defects (contcf) Defect Po in t value II. SHADED PART a. On outside: Variation in shade within a part or between parts I I I. CLEANNESS IV a. Any spot or stain an outside visibl

48、e at 3 feet b. Thread ends (on outside): Not trimmed ta 1/2 inch c. Thread end caught for a distance or more than 1/4 d. Two or more shade or size tickets or loose threads e. Any size or shade marking or residue on outside, (largest dimension in any direction) or less throughout inch in line of stit

49、ching on outside not removed score as spot or stain COMPONENT AND ASSEMBLY a. Any component part or operation omitted (unless otherwise classified herein) b. Any component not as specified c. Any component part tight, twisted, distorted, pleated, or full (unless otherwise classified herein) classified herein) forced out having folds of more than 1/8 inch (unless otherwise classif