ARMY MIL-P-63210-1978 PRIMER PERCUSSION M100 LOADING ASSEMBLING AND PACKING《M100型撞击引物的装药 组装和包装》.pdf

《ARMY MIL-P-63210-1978 PRIMER PERCUSSION M100 LOADING ASSEMBLING AND PACKING《M100型撞击引物的装药 组装和包装》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-P-63210-1978 PRIMER PERCUSSION M100 LOADING ASSEMBLING AND PACKING《M100型撞击引物的装药 组装和包装》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-P-63210 (AR) 29 December 1978 MILITARY SPECIFICATION PRIMER, PERCUSSION, M100 LOADING, ASSEMBLING AND PACKING This specification is approved for use by U.S. Army Armament Research and Development Command, Department of the Army, and is available for use by all Departments and Agencies of the Dep

2、artment of Defense. SCOPE 1, - 1.1 This specification covers the loading, assembling and packing for one tyse of percussion primer designated as Primer, Percussion, M100. 2. APPLICABLE DOCUMENTS 2-1 The following documents of the issue in effect on date of invitation for bids or request for proposal

3、,.form a part of this specification to the extent specified herein. SPECIFICATIONS MI LI TARY MIL-P- 2 2 3 MIL-P-20 449 MI L- A- 4 8 O 7 8 DRAWINGS ARMY 9277103 9328574 9328575 - Powder, Black - Primer, Percussion, M61, Loading, - Ammunition, Standard Quality Assembling and Packing Assurance Provisi

4、ons, General Specification for - Primer, Percussion M100, Loading Assembly - Box, Fiberboard w/Partition Lioose - Packing and Marking for Box, Wirebound, Packing, for Primer, Percussion, M100 Assembly FSC: 1390 Benefichi cO.mrnenta (recommendations, additions, deletions) and any pertinent data which

5、 may be of use in improving thts document should be addressed to: Commander, us AmY Armament Research and Development Command, Attn. DRDARQA, Dover, New JeWY 07801 by using the seli-addresaed Standardization Document Improvement fiopOml (DD Form 1426) appearing at the end of thin document or bp lett

6、er. HIS DOCUMENT CONTAINS 2 PAGES? Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-6 3 210 (AR) (Copies of specifications, standards, drawings and publications required by contractors in connection with specific procurement and functions should

7、 be obtained from the procuring activity or as directed by the contracting officer). 3. REQUIREMENTS 3.1 Material.-Materials and parts shall be in accordance with 3.2 Percussion primer.-The percussion primer shall comply with applicable drawings and specifications. all requirements specified on Draw

8、ing (dwg.) 9277103, and with all requirements specified in applicable specifications. 3.3 Primer assembly 3.3.1 Primer assembly without black powder charge 3.3.1.1 Non-functioninq.-The primer assembly (without black powder charge) shall not function under an applied energy value of 47.52 inch-ounces

9、, iinimum. 3.3.1.2 Functioninq.-The primer assembly (without black powder charge) shall function under an applied energy value of 159.20 inch-ounces, maximum. 3.3.2 Primer assembly with black powder charge 3.3.2.1 Functioninq.-If the percussion element fires, the 3.4 Moisture content of black powder

10、.-The moisture content of primer assemblies shall function without audible hangfire. the black powder at the loading station, at the time of loading shall not exceed 0.5 percent, when tested as specified in 4.3.2. grease, cracks, rust corrosion and other foreign material. The cleaning method used sh

11、all notbe injurious to any of the parts nor shall the parts be contaminated by the cleaning agents used. 3.5 Workmanship.-All parts shall be free of burrs, chips, dirt, 4 QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection and standard quality assurance provisions.-Unless otherwise specif

12、ied herein or in the contract, the provisions of MIL-A-48078 shall apply and are hereby made a part of this detail specification. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b321O 13 777970b 03Li5540 W 7 MIL-P- 6 3 210 (AR) 4.2 Quality Co

13、nformance Inspection 4.2.1 Inspection lot formation.-Inspection lots shall comply with the lot formation provisions of MIL-A-48078. inspection lots of primers shall contain: manufacturer. In addition, a. Metal parts of one lot interfix number from one b. Black powder of one lot number from one manuf

14、acturer. c. Primers, Percussion, M61 of one lot interfix number from 9 one manufacturer. 4.2.2 Examination.-See MIL-A-48078 classification of Defects and Test tables, sampling plans for major and minor defects shall be in accordance with MIL-STD-105, Inspection Level II, except that continuous sampl

15、ing plans in accordance with MIL-STD-1235 may be used if approved by the procuring activity. a. Sampling plans-Unless otherwise specified in the 3 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-63210 13 M 7779706 03955Li1 T M rl N N G - r-l

16、44 8 O O *. rl h da) M O AI Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5 FI rl rl w O h rl P v) rn cd O u 8 .rl k Pi .i 8 .rl k pi i. 6. 5 s rl w kij rlnl O0 rlrl m4- CDO rlrl 3 i - Provided by IHSNot for ResaleNo reproduction or networking perm

17、itted without license from IHS-,-,-MIL-P-63210 13 m 7977706 0345543 3 m Y d a w O h r-l P w 8 2 ko O u .rl k a - 4- hlhl 4- cv mrr) m m . 4- 4 al cri ko 2 9; 6 P Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b32LO 13 m 7797706 0345544 5 m v.?

18、 mm m cv 7 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b32LO 13 7777906 0345545 7 W % d rrl 4-i al a al !2i i! a .rl u4 al a al 2 2 i! Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a al

19、rl v1 2 x O P D N N 4 clc.clN N o omom a sl u al a al 2 d !3 al da 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-n v ad O d N m o I BI I FI MIL-P-63210 13 9 7797706 03Ll55V7 O 1 rl 8 d r b9 bD a P tj k! 4 k P a al FI KJ al vi n I #e O0 44 -I KJl

20、o $3 u 10 I “ R Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-63210 13 m 7777906 03q5548 2 m rl (d 4 3 m M Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-63210 13 9999706 0345549 L1 hl

21、hl Nhl hlhl mm m m mm . . . . _ kM rl Cdl rlhl O0 rld rl hl me o o O0 hl hl NCu 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-63210 13 7779706 0345550 O MIL-P-63210 (AR) 4.2.3 Testinq 4.2.3.1 Primer assembly without black powder charqe 4.2

22、,3,1.1 Non-functioning.-Beginning with the first lot produced and continuing until three consecutive lots have complied with the acceptance criteria specified, a sample of 150 assemblies shall be randomly selected from each lot for the test. If any sample fails to comply with requirement the lot sha

23、ll be rejected. The test shall be performed as specified in 4.3.1.1.1. Primers subjected to this test shall be destroyed. of 4.2.3.1.1, sample of 50 assemblies shall be randomly selected from each lot for this test. If one or more primers fail to comply with the applicable requirement, the lot shall

24、 be rejected. The test shall be performed as specified in 4.3.1.1.1 using equipment in accordance with 4.2.4. Primers subjected to this test shall be destroyed. 4.2.3.1.2 Functioning.-Beginning with the first lot produced and continuing until three consecutive lots have complied with the applicable

25、requirements specified two hundred and fifty samples shall be randomly selected from each lot for this test. If three or more primers fail to comply with the applicable requirements, the lot shall be rejected. If one or two defects are found, a second sample of five hundred primers shall be tested.

26、If the combined number of defectives in both the first and second sample is three or more, the lot shall be rejected. The test shall be performed as specified in 4.3.1.1.2 using equipment in accordance with 4.2.4. 4.2.3.1.1.1 After three consecutive lots have met the criteria 4.2.3.1.2.1 After three

27、 consecutive lots have met the criteria of 4.2.31.2, a sample of 125 primers shall be randomly selected from each lot for this test. If two or more primers fail to comply with the applicable requirement, the lot shall be rejected. one defect is found, a second sample of 250 primers shall be tested.

28、If the combined number of defectives in both the first and second sample is two or more, the lot shall be rejected. The test shall be performed as specified in 4.3.1.1.2 using equipment in accordance with 4.2.4. If only 4.2.3.2 Primer assembly with black powder charCie.-A sample of 25 primers shall

29、be selected from each lot for this test. If anv primer fails to comply with the applicable requirement, the lot * shall be rejected. The test shall be performed as specified in 4.3.1.2.1. 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- I MIL-P-63

30、210 13 m 7779706 0345551 2 m MIL-P-63210 (R) 4.2.3.3 Check test for deterioration of primer, percussion (M61 assembly).-If the total elapsed time between original acceptance of the M61 primer lot and the assembly of that lot into the M100 primer exceeds two years, or if the M61 primers have been sub

31、jected to adverse conditions for any period of time since previous test, the M61 primer lot shall be subjected to and must satisfactorily pass the check test for deterioration specified in Specification MIL-P-20449 immediately before the M61 primer lot is assembled into the M100 primers (see 6.3) .

32、4.2.3.4 Moisture content of black powder.-A sample of one primer shall be randomly selected from each eight hours production. The black powder shall be tested as specified in 4.3.2 and any failure to comply with the applicable requirement shall be cause for rejection of the eight hours production re

33、presented by the sample. 4.2.4 Inspection equipment.-The inspection equipment required to perform the examinations and tests prescribed herein is described in the paragraph Reference/Inspection in Method column in tables starting with paragraph 4.2.2.1. The contractor shall submit for approval inspe

34、ction equipment designs in accordance with the terms of the contract. See section 6 of MIL-A-48078. 4.3 Test methods and procedures 4 . 3.1 Primer assembly 4.3.1.1 Primer assembly without black powder charge 4.3.1,l.l Non-functioninq.-The primer assembly (without black powder charge) shall be assemb

35、led into a test fixture (see 4.2.4). A steel ball weighing a minimum of 7.92 ounces shall be dropped from a height to give the required impact force (approximately 6 inches). 4.3.1.1.2 Functioning.-The test shall be performed as specified in 4.3.1.1.1 except that the weight of the ball shall be 7.96

36、 ounces maximum, and the height shall be adjusted to give the required impact force (approximately 20 inches). 4.3.1.2 Primer assembly with black powder charge 4.3.1.2.1 Functioning.-The primers shall be assembled to the complete round for which the primer was designed and fired from the gun for whi

37、ch the round is standard. to determine compliance with the requirement. The primer shall be observed 14 4 . I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-63210 13 7774906 03q5552 4 I MI L- P- 6 3 2 1 O (AR) 4.3.2 Determination of moisture c

38、ontent of black powder.-The moisture content of the black powder shall be determined in accordance with the procedure specified in Specification MIL-P-223. 5. PREPARATION FOR DELIVERY 5.1 Preservation and packaging 5.1.1 Level C.-The primers shall be preserved and packaged in accordance with dwg. 93

39、28574. 5.2 Packing 5.2.1 Level C.-The cartons shall be packed in accordance with dwg. 9328575. 5.3 Marking.-Marking shall be in accordance with dwgs. 9328574 and 9328575. NOTES 6. - 6.1 Ordering data.-See MIL-A-48078. 6.2 Submission of design for approval.-See 6.2.3 of MIL-A-48078. Submit equipment

40、designs as required, to Commander, ARRADCOM, ATTN: DRDAR-QAR-I, Dover, New Jersey 07801. 6.3 Cost of check tests.-The contracting officer will arrange for the contractor to be reimbursed for the expense incurred in the performance of the check test. The test shall be conducted at Government expense

41、without cost of the contractor who loaded the M61 primer or the contractor loading and assembling the M100 primer, and shall not constitute a basis for rejection against either contractor, except where deterioration has occurred as a direct result of carelessness in handling, storage, etc., while th

42、e primers were under the jurisdiction of either contractor. 6.4 Check test for possible deterioration of percussion artillery primers.-The following tests are designed to prevent the loading of artillery primers which have deteriorated into a maior ammunition item. The- test shall be performed on ar

43、tillery primers from each lot which has been stored under normal conditions for more than two years or under adverse conditions for any period of time. If the specification for the ammunition item into which the artillery primers are loaded does not require that the check test be performed, the cont

44、racting officer should insert a provision for the performance of the check test in the contract. 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-63210 13 m 9999906 0345553 b MIL-P-63210 (AR) 6.4.1 Moisture content of black powder.-A sample

45、of 25 primers shall be selected for this test. The black powder shall be removed from the body by any suitable means. powder shall be determined in accordance with the methods specified in Specification MIL-P-223. tested exceeds 0.7 percent, the lot of primers shall be rejected. test shall be in acc

46、ordance with Table I. Any primer head assembly which fails to comply with the applicable requirement shall be rejected. The black powder shall be removed from the charge cavity prior to performance of this test. *This moisture content of the If .the moisture content of the powder 6.4.2 Primer head a

47、ssembly function.-The sampling plan for this TABLE I Combined Samples Number Number Sample Acceptance Rejection Sample Size Size First Second Third Fourth Fifth Sixth Seventh 75 75 75 75 75 75 75 75 150 225 300 375 450 525 * O O 1 2 2 4 * No acceptance on first sample, * Since black powder is hygros

48、copic, it is advisable to place the powder in a dry, air-tight container immediately upon removal, and to run the determination as soon as possible,thereafter. Custodian: ,Preparing Activity: Army-AR Army-AR Project Number: 139fLAl68 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b32LO L3 777770b 0345554 = ARTILLERY PRIMERS STANDARDS FOR PAINT CONDITIONS IN FLASH HOLES NO, I NO* 2 PREFERRED ACCEPTABLE NO. 3 ACC PTA BL E R N0,4 NO. 5 NOT ACCEPTABLE NOT ACCEPTABLE -L