ARMY MIL-M-62515-1985 MAINTENANCE REPAIR KIT ELECTRICAL FOR M901A2 AND M981 WEAPONS SYSTEMS《型号为M901A2和M981的武器系统的电子保养修理工具》.pdf

《ARMY MIL-M-62515-1985 MAINTENANCE REPAIR KIT ELECTRICAL FOR M901A2 AND M981 WEAPONS SYSTEMS《型号为M901A2和M981的武器系统的电子保养修理工具》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-M-62515-1985 MAINTENANCE REPAIR KIT ELECTRICAL FOR M901A2 AND M981 WEAPONS SYSTEMS《型号为M901A2和M981的武器系统的电子保养修理工具》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、t h v MIL-M-62515 LI9 m 9799906 0252558 O U I I Q-o i-Q3 MIL-M-6 2 5 1 5 (AT) 22 October 1985 SUPERSEDING (see 6.3) MILITARY SPECIFICATION MAINTENANCE REPAIR KIT, ELECTRICAL, FOR M901A1 AND M981 WEAPON SYSTEMS This specification is approved for use by US Army Tank-Automotive Command, Department of t

2、he Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a maintenance repair kit, herein referred to as the kit, used for the maintenance and repair of electrical connectors, contacts, and connector and cable acces

3、sories used on the weapon stations of the M90IA1 and M981 weapon systems. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. Unless otherwise o specified, the following specifications, standards, and handbooks of the issue listed in that issue of the De

4、partment of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of this specification to the extent specified herein. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should

5、be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-GSS, Warren, MI 48397-5000, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document, or by letter. FSC 4910 DISTRIBUTION STATEMENT A. Approved for public release; dist

6、ribution is unlimited. . THIS DOCUMENT CONTAINS JA PAGES Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-IIC q7 m 799970b 01?51?557 2 m MIL-M-62515(AT) SPECIFICATIONS FEDERAL MMM-A- 1 2 1 MMM-A-130 MMM-A- 13 2 MMM-A- 13 4 PPP-c-1752 MILITARY MI

7、L-F-13927 MIL-F-14072 MIL-P-19834 MIL-C-22520/ 3 MIL-C-22520/5 MIL-I-23053/6 MIL-I-81969/8 MIL-I-81969/14 MIL-I-81969/17 MIL-I-81969/19 MIL-1-8 1969/30 - Adhesive, Bonding Vulcanized Synthetic Rubber to Steel. - Adhesive, Contact. - Adhesives, Heat Resistant, Airframe - Adhesive, Epoxy Resin, Metal

8、to Metal - Cushioning Material, Packaging, Unicellular Structural, Metal-to-Metal. Structural Bonding. Polyethylene Foam, Flexible. - Fungus Resistance Test; Automotive - Finishes for Ground Electronic Equipment. - Plates, Identification or Instruction, Components . Metal Foil, Adhesive Back, Genera

9、l Specification for. - Crimping Tools, Terminal, Hand, Wire Termination for Wire Barrel Sizes 20 through 28. - Crimping Tools, Terminal, Hand, Wire Terminations; In-Service Inspection Gages. - Crimping Tools, Terminal, Wire Termination, Large for Coxial, Shielded Contacts and Ferrules, Terminal Lugs

10、, Splices and End Caps. - Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Semi-Rigid, Crosslinked. Electrical Contact, Types I and II, Class 2, Composition A. - Installing and Removal Tools, Connector Electrical Contact, Type III, Class 2, Composition B. - Installing and Removal Tools,

11、 Connector Electrical Contact, Type I, Class 1, Composition C. - Installing and Removal Tools, Connector Electrical Contact, Type II, Class 1, Composition C. - Installing and Removal Tools, Connector Electrical Contact, Type II, Class 2, Composition C. - Installing and Removal Tools, Connector Provi

12、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-N-625L5 L17 W 9777706 0252560 9 W 3 STANDARDS FEDERAL FED-STD-595 - Colors. MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes, MIL-STD-130 - Identification Marking of U.S

13、. Military Property. MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. MIL-STD-454 - Standard General Requirements for Electronic Equipment. MIL-STD-810 - Environmental Test Methods and Engineering Guidelines. MIL-STD-889 - Dissimilar Metals. MIL-STD-45662 - Calibration Syste

14、ms Requirements. 2.1.2 Other Government documents, drawings, and publications. The following documents, drawings, and publications form a part of this specification to the extent specified herein. DRAWINGS ARMY 1231 1946 - Maintenance Repair Kit. (Copies of specifications, standards, handbooks, draw

15、ings, and publications required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 2.2 Order of precedence. In the event of a conflict between the text of this specification and the reference

16、s cited herein, the text of this specification shall take precedence. 3. REQUIREMENTS 3.1 First article. Unless otherwise specified (see 6.2), the contractor shall furnish kits which shall be subjected to first article inspection (see 4.4). information, shall be representative of the units to be fur

17、nished to the Government. All subsequent kits delivered to the Government shall conform to these samples in all of their pertinent physical and performance attributes. First article inspection samples, properly marked with identifying 3.2 Materials. Materials shall be as specified herein and in appl

18、icable specifications, standards, and drawings. When a definite material is not specified, the material used shall be suitable for the purpose and shall I - enable the kit to meet the performance requirements of this specification 0 (see 4.8.1). 3 Provided by IHSNot for ResaleNo reproduction or netw

19、orking permitted without license from IHS-,-,-MIL-M-6 25 15 (AT) 3.2.1 Case. The case shall be fiberglass with an aluminum alloy frame (see 4.8.1). 3.2.2 Hinged covers and attaching components. The hinged covers and attaching components shall be aluminum alloy, clear anodized in accordance with MIL-

20、F-14072 (see 4.8.1). 3.2.3 Clasps, handles, and hinges. The clasps, handles, and hinges shall be suitably protected to resist corrosion (see 4.8.1). 3.2.4 Inserts and retainer pads. The inserts and retainer pads shall be fire-retardant foamed polyethylene in accordance with PPP-C-1752 (see 4.8.1). 3

21、.2.5 Instruction handbook sheets and contents charts. The instruction handbook sheets and contents charts shall be 0.020-inch thick white vinyl (see 4.8.1). 3.2.6 Adhesives, Adhesives shall be in accordance with MMM-A-121, llfil-A-130, IiMM-A-132, or MMM-A-134 (see 4.8.1) . 3.2.7 Dissimilar metals.

22、The use of dissimilar metals in contact with each other shall be avoided unless suitably protected against electrolytic corrosion in accordance with requirement 16 of MIL-STD-454. Dissimilar metals are as specified in MIL-STD-889 (see 4.8.1). 3.3 Design and construction. The kit shall be designed an

23、d constructed as specified herein (see 4.5.2 and 4.8.2). 3.3.1 Configuration. The kit shall conform to figures 1 and 2 (see 4.5.2 and 4.8.2). 3.3.2 - Color. The color of the case shall be olive drab in accordance with number 24087 of FED-STD-595 (see 4.5.2 and 4.8.2). 3.3.3 Rubber feet. Rubber feet

24、shall be provided on the back and bottom of the case as shown in figures 1 and 2 (see 4.8.3). 3.3.4 Hinged covers. The hinged covers shall be as shown in figure 2. Each hinged cover shall have latch and a retainer pad (see figure 5) permanently affixed to the underside that will retain the tools in

25、their reepectve positions when tkc hinged cover is closed. Each hinged cover shall have a warning label stating: “CAUTION: Lock this lid before closing“ (see 4.8.3) . 3.3.5 Jnstreon handbook and contents chart. The lettering shall be. black, legible, and protected with a trnnsparent coating. The ins

26、truction handbook sliabl conteEn a cover sheet with appropriate identification, detailed tool usage instructions and diagrams, and a connector part number breakdown appeti4i.x giving the shell sizes, insert arrangements, and the sizes and qunntitlec of contacts found in the connectors serviced by th

27、e tool kit. The contents charts shall. be centered on the inside of the top and bottom Mnged covers, shall have a pressure-sensitive adhesive backing, and shall show the insert cavity configurations (see figures 3 and 4) and the respective tool part nuubers (see 4.8.3). 4 Provided by IHSNot for Resa

28、leNo reproduction or networking permitted without license from IHS-,-,-MIL-M-625L5 LI9 = 7777706 0252562 2 MIL-M-62515(AT) / / /- ,- /- 1 ,- 3.3.6 Foamed inserts. The foamed inserts shall be as shown ip=figures 6 1 and 7 (see 4.8.3). I i ,fi - 3.3.7 Contents. The kit shall contain the items or.their

29、 approved equivalents specified in table I and shown in figures 8 through 11, arranged as shown in figures 3 and 4 (see 4.8.3). 3.3.7.1 Tools. The tools shall conform to the corresponding cpeeificatfons as shown in table II. (see 4.8.1). /y - 3.4.1 Low pressure (altitud). The kit with contents shall

30、 not be damaged when exposed to a pressure equfvalent to an altitude of 40 O00 feet / (see 4.8.4.1). - 3.4.2 High temperature. The kit with contents shall-not be damaged- when exposed to a temperature of 160 degrees Fahrenheit (OF) (see 4.8.4.2). 3.4.3 Low temperature. The kit with contents shall no

31、t be damaged when exposed to a temperature of minus 70F (see 4.8.4.3). 3.4.4 Solar radiation (sunshine). The kit with contents shall not be damaged when exposed to solar radiation (see 4.8.4.4). 3.4.5 Rain. The kit with contents shall not be damaged, and there shall 0 be no evidence of water or mois

32、ture accumulation inside the case, when exposed to blowing rain (see 4.8.4.5). 3.4.6 Humidity. The kit with contents shall not be damaged by exposure to 95 percent (%) relative humidity (see 4.8.4.6). 3.4.7 Fungus. The kit with contents shall not support fungus growth when exposed to conditions favo

33、rable for their development (see 4.8.4.7). 3.4.8 Salt fog. The kit with contents shall show no evidence of corrosion that could impair the operation of the kit and contents when exposed to a salt fog atmosphere (see 4.8.4.8). 3.4.9 Dust. The kit with contents shall not be damaged when exposed to blo

34、wing dust (see 4.8.4.9). 3.4.10 Leakage (immersion). The kit with contents shall not be damaged, and there shall be no evidence of water or moisture accumulation inside the case, when immersed in water to a depth of 3 feet (see 4.8.4.10). 3.4.11 Vibration. “he kit with contents shall not be damaged

35、when tested as specified in 4.8.4.11. 3.4.12 Shock. The kit with contents shall not be damaged when tested as specified in 4.8.4.12. O 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M I L-M-625 15 (AT) al bo P 8 tl *rl U U al E H i k w d O O U bo

36、E -I4 a E! .r( k V Fi al E O d U 4 pi 8 k O 4 U d VI O pi E k al 0 O 1-I U 1-I pi 8 al k w d O O U bo c d a 1-I B a 8 d O O U d (d El al k al 1-I o n U Q) v) al 1-I n U al VI al 4 n al d -3 c d O O U d (d El 3 g 2 al V I c; *rl Oe a *rl 111 u U d O U tl k al P d U k td pc El 2 2 m MIL-M-62515 47 9 7

37、779706 0252564 6 m MI L-M-62515(AT) 3-4 3-4 rl O O u rl td i 2 O O U M d *rl rl rl (d u H 2 rl O O U rl td P 8 8 O O u M 0 .rl rl rl td U H 2 , 4 .O O rl U O O M U d *d d rl td rl td U e 2 2 H rl O O U rl td P O a d k al a a .rl k U 111 al k *rl s 111111 rlrl alal A h in .n m 03 h a Co d h O m a a m

38、 O 00 m m m m m a 4 m a a a e 6 e I I I I h m m N d m 4 h h h b e N 4 4 d O O m I O I I I I I I O O O O O O O O O O O O O I O I I I I O O o O I O N N N N N N 4 d I+ 4 d 4 4 rl rn m rn m m m m I I D h I I O I I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

39、IHS-,-,-I 2 E 4 U E O CJ I !3 4 U a U W-I W 4 U E QI 3 D 8 VI U U E e U w E-r Fi flIL-M-b25L5 44 W 44934Ob 02525b5 8 MIL-M-62515(AT) 44444 4 n un ua O0 PU vw 8 n U U O Ja v U k al VI E H 8 n a O U v U M QI H U k a 4 d 8 VJ U U E U 2 -3 d VI U U CJ QI CJ 8 l-l cn 1 Q 8 Provided by IHSNot for ResaleNo

40、 reproduction or networking permitted without license from IHS-,-,- I I MIL-M-b25L5 Li9 = 7777706 025256b T - , 3.5 Identification and marking. Identification and marking shall be in a accordance with MIL-STD-130 and shall be permanent and legible (see 4.5.2 and 4.8.2). 1 3.5.1 Nameplates. The namep

41、lates shall be marked with the information specified in figure 1, shall be 0.003- to 0.005-inch thick aluminum foil in accordance with MIL-P-19834, and shall be permanently mounted, The marking shall be black on a light background (see 4.5.2, 4.8.1, and 4.8.2). 3.6 Workmanship. Workmanship shall be

42、in accordance with high-grade practices and quality and free of sharp edges, burrs, cracks, corrosion, or any other defect or feature which is a potential personal hazard to the operator during normal usage (see 4.5.2 and 4.8.2). - - 4. QUALITY ASSURANCE PROVISIONS -? - - 4.1 Responsibility for insp

43、ection. Unless otherwise specified in the contract or purchase order (see 6.2), the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilitie

44、s suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. The Government reserves

45、 the right to perform or witness any of 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection req

46、uirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply wih all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective mat

47、erial, either indicated or actual, nor does it commit the Government to acceptance of defective material. a 4.1.2 Inspection equipment. Unless otherwise specified in the contract (see 6.2), the contractor is responsible for the provision and maintenance of all inspection equipment necessary to assur

48、e that supplies and services conform to contract requirements. Inspection equipment must be capable of repetitive measurements to an accuracy of 10 percent of the measurement tolerance. Calibration of inspection equipment shall be in accordance with MIL-STD-45662. 4.2 Classification of inspection: a

49、. First article inspection (see 4.4). b. Quality conformance inspections (see 4.5). 1. Examination (see 4.5.2). 2. Tests (see 4.5.3). C. Control tests (see 4.6). 9 i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-bSSLC 47 W 777970b 021525b7 I 4.3 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be co