ARMY MIL-I-12597 C (2)-1993 IGNITER BLASTING FUSE FRICTION TYPE M3A1 LOADING ASSEMBLING AND PACKING《M3A1型冲锋枪摩擦式起爆引信点火器的装卸 组装及包装》.pdf

《ARMY MIL-I-12597 C (2)-1993 IGNITER BLASTING FUSE FRICTION TYPE M3A1 LOADING ASSEMBLING AND PACKING《M3A1型冲锋枪摩擦式起爆引信点火器的装卸 组装及包装》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-I-12597 C (2)-1993 IGNITER BLASTING FUSE FRICTION TYPE M3A1 LOADING ASSEMBLING AND PACKING《M3A1型冲锋枪摩擦式起爆引信点火器的装卸 组装及包装》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、a I MIL-I-L259?C (2) 999SSOb 1845242 079 !I INCH-POUND MIL-I-l2597C(AR) AMENDMENT 2 11 February 1993 SUPERSEDING AMENDMENT 1 6 December 1977 MILITARY SPECIFICATION IGNITER, BLASTING FUSE, FRICTION TYPE, M3A1 LOADING, ASSEMBLING AND PACKING This Amendment forms a part of Military Specification MIL-I-

2、2597C(AR), dated 23 May 1975, and is approved for use by the US Army Armament, Munitions and Chemical Command, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 2.2: Change “Industrial Checmicals“ to “industrial Chemicals“. PAGE 3 * 2.1, Add the following:

3、 MIL-B-117 - Bag, Sleeve and Tubing - Interior Packaging“ 1.11,-STD-129 - Marking for Shipment and Storage“ 3.3 Uelete in its entirety and substitute the following: 3.3 Tumble. The igniter shall not disassemble or ignite when sub- to the Tumbling Test. PAGE 8 * 4.4.2.2 Clip Safety, Minor 201: Delete

4、 “Diameter of Eyelet“ and substitute “Outside dimension of eyelet“. AMSC N/A DISTRIBUTION STATEMENT A. 1 of 3 FSC 1375 Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-l2597C(AR) AMENDMENT

5、2 PAGE 22 4.5.3: Change “Approximately 500“ to “400 plus or minus 50“. Change O . segregate those igniters which ignited during tumbling“ to “reject and remove from the lot those igniters which lost safety clips, disassembled or ignited during tumbling. “ PAGE 23 * 5.1.2: Add paragraph as follows: “

6、5.1.2 Level C. Four hundred Igniter, Blasting FUX shall be packed in a domestic class, fiberboard box of Spec PPP-B-636. They shall be arranged, on end, in 10 rows of 20 each with a fiberboard spacer between rows. A fiberboard iller shall be placed on top of the bottom layer of 200 igniters and a se

7、cond layer of 200 igniters shall be packed on top as above except the position f the ends of the igniter shall be alternated. Add additional fillers, as required, to insure tight packing. seal the box, blunt all corcers and place into a barrier bag, Type I, Class E OE Spec 1;,-8-117. Exhaust excess

8、air within bag and seal in accordance with manufacturers instructions. If required by the contract, the sealed package shall comply with the quick leak test of Spec MIL-P-116. “ * 5.2.2: Add paragraph as follows: “5.2.2 Level C. Twelve boxes (total 4800 Igniters), packaged and sealed as cited in 5.1

9、.2, shall be packed in an overseas class (waterproof), fiberboard box meeting the requirements of code of Federal Regulations (CFR), Title 49, Parts 100-199. Fillers shall be added around and on top of the inner boxes to insure tight packing. The box shall be securely sealed to meet the requirements

10、 of the code of Federal Regulations. “ * 5.3: Delete paragraph and substitute the following: “5.3 Marking. 5.3.1 Level A. The boxes and bags shall be marked as specified on dwgs. 8835011 and 8835012. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

11、MIL-I-l2597C(AR) AMENDMENT 2 5.3.2 Level C. The boxes and bags shall be marked in accordance with MIL-STD-129 and CFR Title 49, Parts 100-199.“ 6.2: Change address to: .Commander, US Army Research, Development and Engineering Center, ATTN: SMCAR-QAT-I, Picatinny Arsenal, NJ 07806-5000. 6.3: Change a

12、ddress to: “Commander, US Army Research, Development and Engineering center, ATTN: SMCAR-QAT-M, Picatinny Arsenal, NJ 07806-5000. The margins of this amendment are marked with a asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous

13、amendment were made. This was done as a convenience only and the government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to eveluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Cu s tod i an : Army-AR Preparing activity: Army-AR (Project 1375- 503) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-