ARMY MIL-F-63434 A (3)-1990 FUZE PROBE ASSEMBLY SPRING ASSEMBLING AND PACKING (TOW)《引信探针组装 弹簧组装和包装(陶式武器)》.pdf

《ARMY MIL-F-63434 A (3)-1990 FUZE PROBE ASSEMBLY SPRING ASSEMBLING AND PACKING (TOW)《引信探针组装 弹簧组装和包装(陶式武器)》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-F-63434 A (3)-1990 FUZE PROBE ASSEMBLY SPRING ASSEMBLING AND PACKING (TOW)《引信探针组装 弹簧组装和包装(陶式武器)》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-F-63434A (AR) AMENDMENT 3 23 March 1990 SUPERSEDING AMENDMENT 2 7 November 1983 MILITARY SPECIFICATION FUZE PROBE ASSEMBLY, SPRING ASSEMBLING AND PACKING (TOW) This Amendment forms a part of Military Specification MIL-F-63434A (AR), dated 30 August 1982, and is approved for use within the U.S. A

2、rmy Armament, Munitions and Chemical Command and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 * Standards, Military: Add the following: MIL-STD-1169 - Packaging, Packing and Marking for Shipment of Inert Ammunition Components.“ PAGE 3 3.7.4: Delete paragr

3、aph and substiiute with the following: “Electrical resistance of brown wire to inner ogive shall not exceed 0.5 ohm.* 3.7.5: Add the following: ElectricaI resistance between the brown and black wires shall be 100 megohms minimum at 100 + 5 Vdc.“ - PAGE 20 4.4.2.13: Add under Major: “106 Length from

4、end of small groove 1.Q Gage.“ PAGE 40 4.4.2.33: Add under Major: 103 Location of groove 1.0 Gage. II AEiC N/A 1 of 2 FSC 1336 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

5、HS-,-,-MIL-F-63434A (AR) Amendment 3 PAGE 43 4.4.2.36: Add under Major: 104 Distance from thread end to chamfer at O.D. 1.0 Gage.“ PAGE 48 4.4.2.41: Add under Major: 105 Shoulder to chamfer at O.D. 1.0 Gage.“ PAGE 83 * 5.1 and 5.2: Delete in their entirety and substitute the following: 5.1 Packaging

6、 and packing. The parts shall be packaged and packed in accordance with the requirements of MIL-CTD-1169. 5.2 Marking. Marking shall be in accordance with requirements of MIL-STD-1169. NOTE: The margins of this amendment are marked with an asterisk or vertical line to indicate where changes (additio

7、ns, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the government assumes no liability whatsoever for any inaccuracies in these nota-tions. Bidder and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Custodian: Army-AR Preparing activity: Army-AR (Project 1336-A606) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-