ARMY MIL-DTL-3628 62 E-2008 BADGE QUALIFICATION COMMAND ASHORE COAST GUARD《海岸警卫队路上司令部资质徽章》.pdf

《ARMY MIL-DTL-3628 62 E-2008 BADGE QUALIFICATION COMMAND ASHORE COAST GUARD《海岸警卫队路上司令部资质徽章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 62 E-2008 BADGE QUALIFICATION COMMAND ASHORE COAST GUARD《海岸警卫队路上司令部资质徽章》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND MIL-DTL-3628/62E 1 November 2008 SUPERSEDING MIL-DTL-3628/62D 15 November 1996 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, COMMAND ASHORE, COAST GUARD This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring t

2、he product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3628. DASH NO. -1: Regular Size -2: Miniature Size MATERIAL: Red Brass FINISH: WREATH AND EAGLE: Gold Plated, Matte Finish, Polished Highlights and shall match The Institute of Heraldry (TIOH) Metal

3、 Finish Chip Number 8. SHIELD, ANCHOR AND ROPE: Nickel Plated, Mirror-like Polished and shall match TIOH Metal Finish Chip Number 16. DIMENSIONS: HEIGHT (overall): -1: 1-3/8 inches (REF) -2: 11/16 inch (REF) AMSC N/A Page 1 of 2 FSC 8455 Provided by IHSNot for ResaleNo reproduction or networking per

4、mitted without license from IHS-,-,-MIL-DTL-3628/62E Page 2 of 2 WIDTH (overall): -1: 1-9/16 inches (REF) -2: 13/16 inch (REF) THICKNESS (thickest point at shield): -1: 0.125 inch + 0.005 inch -2: 0.085 inch + 0.005 inch NOTES: 1. The term (REF) refers to the measurements taken from the Government f

5、urnished hub or die. 2. Piercing shall be as indicated. 3. The attaching device shall be prong and clutch type. The prongs shall be located as follows: Dash No. -1: One prong shall be located on the vertical center line 1/8 inch + 1/16 inch from the bottom of the badge. Two prongs shall be located o

6、n a horizontal line 1-3/16 inches + 1/16 inch from the bottom of the badge, equidistant from each side and 1-3/16 inches + 1/16 inch apart. Dash No. -2: Two prongs shall be located on a horizontal line 7/16 inch + 1/6 inch from the bottom of the badge, equidistant from each side and 11/16 inch + 1/1

7、6 inch apart. 4. Shield, anchor and rope may be rhodium plated, mirror-like polished and shall match TIOH Metal Finish Chip Number 16 at the option of the manufacturer. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issu

8、e due to the extent of the changes. Custodian: Preparing activity: Army - IH Army - IH Navy - NU (Project No. 8455-2009-006) Review activities: DLA - CT Coast Guard - CG NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-