ARMY MIL-D-70430 (5)-1996 DECELERATOR RAM AIR PARTS AND CONTAINER ASSEMBLY《冲压空气减速机的零件及集装箱零件》.pdf
《ARMY MIL-D-70430 (5)-1996 DECELERATOR RAM AIR PARTS AND CONTAINER ASSEMBLY《冲压空气减速机的零件及集装箱零件》.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-D-70430 (5)-1996 DECELERATOR RAM AIR PARTS AND CONTAINER ASSEMBLY《冲压空气减速机的零件及集装箱零件》.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-D-70430 (5) 9999906 2025332 29T 1 INCH-POUND 1 MILITARY MIL-D-70430 (AR) AMENDMENT 5 - SUPERSEDING AMENDMENT 4 22 June 1994 SPECIFICATION DECELERATOR, RAM AIR, PARTS AND CONTAINER ASSEMBLY This amendment forms a part of MIL-D-70430 (AR), dated 12 September 1983, and is approved for use by the U.
2、S. Army Armament Research, Development and Engineering Center, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 3 * 3.4.1: Delete in its entirety and substitute the following: “3.4.1 RAD inteuritv. The RAD Assembly Complete shall not display any broken thre
3、ads nor opening of the weave around any stitch greater than 1/8 inch square after being inflated to peak pressure within a duration interval not to exceed 14.0 milliseconds by an inert gas which is exhausted by means of a solenoid valve from a lecture bottle (having an internal volume of27.0 CU. in.
4、 minimum) pressurized to 490 + 10 psi.“ 3.5: Delete in its entirety. PAGE 4 4.3.1, Parts Description: Delete “Scoop Assembly; Panel Assembly, Lower RAD; and Packing Container, RAD“ in its entirety. TABLE I: Delete “Scoop Assembly; Panel Assembly, Lower RAD; and Packing Container, RAD“ in its entiret
5、y. AMSC N/A 1 of 6 FSC 1330 DISTRIBUTION STATEM ENT 4. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-D-70430 (5) 9 9999906 2025113 126 9 MIL-D-70430 (AR) AMENDMENT 5 PAGE 7 TABLE I, under
6、RAD Assembly, Complete: Delete “RAD Integrity“ in its entirety. PAGE 8 TABLE I: Under RAD Container Assembly, add “FWD Integrity 50 3.4.1 4.5.1“. Delete Thermal Shock in its entirety. PAGE 10 4.4.2.1: Delete “Majors 102, 103, and 105“. Add Minor 203 “Major diameter .65% 3.4 Gage“. PAGE 11 4.4.2.2, M
7、ajor 101: Add “(a)“ next to .40%. Add Note (a) to Notes block: “(a) Special inspection level, S-4, Of MIL-STD-105. II PAGE 12 4.4.2.3: Delete Major 101 in its entirety. Delete Majors 102 and 104 in their entirety. Delete Minor 201 and substitute “Major diameter .65% (a) 3.4 Gage“ . Delete Minor 202
8、and substitute “Flatness 3.4 Gage“ . Delete Minor 203. Add next to .40% (2 places). .65% (a) Add Note (a) to Notes block: “(a) Special inspection level, S-4, Of MIL-STD-105. II 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-D-70430 (5) - 99999
9、0b 2025114 Ob2 MIL-D-70430 (AR) AMENDMENT 5 PAGE 13 4.4.2.4: Major 102: Delete “from center“. Delete Minor 202 and 203 in their entirety. Delete Minor 204 and substitute “Blend radius .65% 3.4 Gage“ . Add Minor 205: “Notch .65% 3.4 Add Minor 206: “Small hole diameters .65% 3.4 Gage“ . .65% 3.4 Gage“
10、 . Add Minor 207: “Small hole locations Add Minor 208: “Center hole diameter Gage“ . of four-hole pattern) of four-hole pattern) .65% 3.4 Gage“ Add 18(a)p next to .40% (2 places) and .65% (7 places). Add Note (a) to Notes block: “(a) Special inspection level, S-4, Of MIL-STD-105. I PAGE 14 4.4.2.5:
11、4. Major 101: Delete “100%“ and substitute I .40%“. Add Major 102: “Rivets improper .40% 3.4 Gage“ . PAGE 15 4.2.6: Delete Minor 202 and substitute “Profile of scoop -65% 3.4 Gage“ . Delete Minor 203. Add (a) I next to -65% (4 places) . Add Note (a) to Notes block: “(a) Five units per cutting die pe
12、r 60,000 pieces. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PAGE 16 4.4.2.7: Minor 201: Delete “Scoop lengthl and substitute “Centerline to outermost intersection of scoop (horizontal)“. Minor 202: Delete “Scoop width and substitute “Centerlin
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILD7043051996DECELERATORRAMAIRPARTSANDCONTAINERASSEMBLY 冲压 空气 减速 零件 集装箱 PDF

链接地址:http://www.mydoc123.com/p-442591.html