ARMY MIL-C-63461-1981 CONTAINER AMMUNITION METAL FOR PROPELLING CHARGES AND CARTRIDGES《金属弹药及炮弹集装箱的装药推进系统》.pdf

《ARMY MIL-C-63461-1981 CONTAINER AMMUNITION METAL FOR PROPELLING CHARGES AND CARTRIDGES《金属弹药及炮弹集装箱的装药推进系统》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-63461-1981 CONTAINER AMMUNITION METAL FOR PROPELLING CHARGES AND CARTRIDGES《金属弹药及炮弹集装箱的装药推进系统》.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、- MIL-C-63461 B1 i 7777706 0287272 2 i! ,- MIL-C-63461 (AR) 20 JULY 1981 MILITARY SPECIFICATION CONTAINER, AMMUNITION, METAL, FOR PROPELLING CHARGES AND CARTRIDGES This specification is approved for use by the U.S. Army Armament Research and Development Command, and is available for use by all Depar

2、tments and Agencies of the Department of Defense . 1. SCOPE 1.1 This specification covers one type of metal container used for packing propelling charge6 or separate loaded artillery ammunition and for packing cartridges. 2 . APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on

3、 date of invitation for bids or request for proposals form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL TT-C-490 MILITARY MIL-A-48078 -Cleaning and Preparation of Ferrous and Zinc Coated Surfaces for Organic Protect ive Coatings -Welding Resistance, Spot, Seam

4、and Production, for Fabricating Assem- blies of Low-Carbon Steel -Ammunition, Standard Quality Assurance Provisions, General Specification For -,7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63461 81 9799906 0289273 4 MIL-(2-63461 (AR) STAN

5、DARDS MILITARY MIL-STD-105 -Sampling Procedures and Tables for MIL-STD-171 -Finishing of Metal and Wood Surfaces MIL-STD-1188 -Commercial Packaging of Supplies and MIL-STD-1261 -Welding Procedures for Constructional Inspection by Attributes Equipment Steel DRAWINGS (see 6.2) US ARMY ARMAMENT RESEARC

6、H AND DEVELOPMENT COMMAND (ARRADCOM) 9331196 9331197 9331198 9331199 9331200 9331201 9331202 9331203 9331204 9331205 -Container, -Contai ner , -Conta iner, -Container, -Container , -Container, -Conta iner, -Container, -Container , -Container, Ammo. , Ammo. , Ammo., AIWIIO. mo., Ammo., Ammo., Ammo.,

7、Ammo., AINnO., Metal: Metal: Metal: Metal: Metal: Metal: Metal: Metal: Metal: Metal: PA9 1 PA9 2 PA9 3 PA94 PA9 5 PA9 6 PA9 7 PA98 PA9 9 PA100 (Copies of specifications, standards, drawings and publications required by suppliers in connection. with specific procurement functions should be obtained f

8、rom the procuring activity or as directed by the contracting officer) . 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply

9、. AMERICAN SOCIETY FOR TESTING MATERIALS ASTM-D412 -Tension Testing of Vulcanized ASTM-D2240 -Indentation Hardness of Rubber Rubber, Standard Method of and Plastics by Means of a Duro- meter, Standard Method of Test for Materials, Standard Method of AS TM- E8 -Tension Testing of Metallic 2 Provided

10、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-636L 81 9777906 0287274 6 MIL-C-63461 (AR) AMERICAN SOCIETY FOR TESTING MATERIALS (Contd) ASTM-E18 . -Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials, Test for (Application for c

11、opies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103) 3. REQUIREMENTS -. 3.1 Materials. Materials and parts shall be in accordance with applicable #drawings and specifications. 3.2 Containers. The containers (container assemblies) shal

12、l comply with all requirements specified on drawings (dwgs.) 9331196 through 9331205 as applicable, and associated drawings and with all requirements specified in applicable specifications and standards. - 3.3 Welding. The welding shall comply with the require- ments of MIL-W-,12332 or MIL-STD-1261.

13、 . 3.3.1 Tensile strenqth (if applicable) . The tensile - strength of the longitudinal body weld shall not be less than 65 percent of the tensile strength of body material when tested as specified in 4.5.1. 3.4 Painted surface. The painted exterior surface of the container shall comply with the requ

14、irements of TT-(2-490 except that the film thickness, and salt spray requirements of TT-(2-490 shall not apply to the interior surfaces and welded spots and sharp corners of the exterior surface of the containers . 3.5 Cover assembly. Upon assembly of the cover assembly to the body assembly (body we

15、ldment) I the cover assembly shall freely engage and rotate within the body assembly. As the cover assembly is rotated with the “Yn handle in the open position, the “Yn handle shaft ends shall freely engage into the respective bayonet slots of the rim. When the “Yn handle is in the closed position (

16、rotated 1800), the spring clip shall engage and lock the handle in place. When the spring clip is disengaged and the handle rotated to the open position, the cover assembly shall disengage from the body assembly. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

17、from IHS-,-,-MIL-C-63461 (AR) 3.6 First article inspection. This specification contains technical provisions for first article inspection. ments for the submission of first article samples by the contractor shall be as specified in the contract. Require- 3 . 7 3.7.1 Containers. The containers shall

18、be regular, Wor kmansh ip . smooth, and free from wrinkles, pin holes, cracks, rough spots, burrs, sharp edges and any other defect that might affect the serviceability, durability, safety and appearance of the . container . accordance with. applicable drawings and comply with instruct ions in MIL-S

19、TD-171 . 3.7.3 Parts. All parts shall be free of chips, dirt, grease, rust and foreign material. shall not be injurious to any of the parts nor shall any of the parts be contaminated by the cleaning agents used. 3.7.2 Paint coatinq. The paint coating shall be in The cleaning method used 4. QUALITY A

20、SSURANCE PROVISIONS 4.1 Responsibility for inspection and standard qualit assurance provisions. Unless otherwise specified herein 05 in the contract, the provisions of MIL-A-48078 shall apply and are hereby made a part of this detail specification. 4.2 Classification of inspections. The following ty

21、pes of inspection shall be conducted on this item: a. First Article Inspection b. Quality Conformance Inspection 4.3 First article inspection. 4.3.1 Submission. The contractor shall submit a first article sample as designated by the Contracting Officer for evaluation in accordance with provisions of

22、 4.3.2. The first article sample shall consist of five (5) painted container assemblies, five (5) painted cover assemblies, five (5) unpainted cover assemblies, and ten (10) each of every subassembly and component (unpainted). 4.3.2 inspections to be performed. See MIL-A-48078 and Table I specified

23、herein. 4.3.3 Rejection. See MIL-A-48078. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63461 81 m 9999906 0287276 T * I k 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6 . 3 O mm rimm P

24、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-63LlbL 81 m 7777906 0287278 3 = MIL-C-6 3 4 6 I (AR) 4.4 Quality conformance inspection. 4.4.1 Inspection lot formation. Inspection lots shall comply with the lot formation provisions of MIL-A-480

25、78. addition, inspection lots of containers shall contain material from lots with the same interfix number from one manufacturer. In 4.4.2 Examination - See MIL-A-48078. Unless otherwise specified in the Classification of Defects and Test Tables, sampling plans and procedures for major and minor def

26、ects shall be in accordance with MIL-STD-105, Inspection Level II. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-634bL 81 W 7779706 0289279 5 = z z t O u a, c O - mm ww r v) 5 E Y L O 5 L O O a rc O w V E w 2 w W Provided by IHSNot for Resa

27、leNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63461 8l 1 3999906 0287280 l 000000 o i cn E L v, ar ta . U ei c rc QI QI c O .r- n rc O aJ u C al U .C w 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b3LIbL 82 M

28、 999990b 0289282 3 W c Y n 8 Y Y Z O 5 u U QI In 3 InU QC ou la n la .w cr- O a In ar ulul UC am E CY OL O u3 r aJL In0 alo Ln rc u0 O CaJ U cnr 3aJ I- -0 u ar- a CZW n -c O VI F . U aJ c cc aJ .I- n a. c O -* L O P a =I IV, Provided by IHSNot for ResaleNo reproduction or networking permitted withou

29、t license from IHS-,-,-1 i .- rl b rl MIL-C-63461 81 7779706 0289282 5 m, 12 m dpdp dp O0 3 e. O0 O . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63qbL 81 W 99979-06 0289283 7 W #a# #a# # O000 00000 O0 eeqe wdieew di- *# mmm www . . . . . .

30、 . . . . O000 00000 O0 O00 a m a! O U al rl s 2 x 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IL-C-63461 81 7779706 0287284 7 1 P 5 =I VI *I- aJ en Iu -!?Cu. Cu. Cu. mmmmm m m h m . aJ VI aJ aJ E: L U O r 5 en c P 5 Y P X O VY rc LLO aJaJ U aJ

31、 t rc aJ .I- n aJ U t aJ U .r al K O w Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-tIIL-C-6346L 81 9 9999706 0289285 O i! dpdpdp dp O00 O00 3 O 22: . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

32、,-MIL-C-63LIbL 81 7779706 028728b 2 - dpdpdpdp a, O000 O000 M . 8 4444 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-W Co W vl m d - rl 8 rl MIL-C-63461 1 = 7777906 0287287 4 W . * 9 O0 Provided by IHSNot for ResaleNo reproduction or networking per

33、mitted without license from IHS-,-,-MIL-C-63461 81 7777706 0287288 b I O i. 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-rl B rl E B MIL-C-63461 81 W 9999906 0289289 8 W i,. 4 i; $a$ c e O00 s z u4 O AI 18 +- . Provided by IHSNot for ResaleNo r

34、eproduction or networking permitted without license from IHS-,-,-. O i9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-rl ti rl tIIL-C-63LtbL 3 - 7777706 0287273 b =I “! m m 8 8 O * 3 . O -0 Provided by IHSNot for ResaleNo reproduction or networking

35、 permitted without license from IHS-,-,-i rl W ! *. MIL-C-63461 81 7797906 0289292 B W f d w * O0 . - a .d FI !?I - . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. -. L L LaJL w v) aJ u CI 7 n Cu v) c ic r v) v) LT v) CI O E L CnY U EL 5 .F o v)5

36、 .) CI n c v) I- L EO an F O+ -Co aJaJ CIS EaJ I- u CI I- L nw FI I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-tlIL-C-63qhL 81 m 9797706 0287274 L = E w w il0 !* . W c O c . Y c L n E - *I- O E 3 U L O O Q rc O W o E W U w 23 Provided by IHSNot

37、for ResaleNo reproduction or networking permitted without license from IHS-,-,-o t- v3 rl M M o 4 i r NIL-C-6346L Bl = 9999706 OSB72953 L lQ 3 ln .I- O . U E % er- n aJ E O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-63461 1 977970b 0289296

38、 5 m O000 by u) O 9 I U ai E5 *I- % n aJ c O P -c v) c RI E Y L O 3 L O O .I- n % aJ u C aJ U W -I- I l I 25 69 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. -. .- . . . - . . . - . . . . . . . . . . . -. - . . . . . . . ._ . . - . -. . . . - - .

39、 . - . . . . . - . . . . . . . . . . - . .- - MIL-C-b34bL 81 = 777770b 0287277 7 rl 8 rl 2 I4 sv 4 L) O 8 68 8 .5 I AI dl . 26 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- i E- -a dp dp- O0 ew dpdp w ww i! mrn 88 8 88 al “ Provided by IHSNot fo

40、r ResaleNo reproduction or networking permitted without license from IHS-,-,-u MIL-C-63462 81 7397706 0287279 O W MIL-(2-63461 (AR) 4.4.3 Testinq. 4.4.3.1 Tensile strenqth (see 3.3.1), Major Defect.- Five (5) bodies shall be randomly selected for this test. Four specimens, approximately equally spac

41、ed along the axis, shall be taken from each body at right angles to the weld. If one or more specimens of a sample fail to comply with the requirement, that sample shall be classed defective. If two or more samples are classed defective, the lot shall be rejected. 4.4.3.2 Weld of rim to body (see 93

42、31684), Major Defect.- Five (5) body assemblies shall be selected for this test. If any sample fails to comply with the requirement, the lot shall be rejected. 4.4.3.3 grinq embrittlement (see dwg. 9331694), Major Defect.- Five (5) springs shall be randomly selected from each heat treatment lot for

43、this test. If any spring fails to meet the requirement, the heat treatment lot shall be rejected. 4.4.3.4 Hardness of sprinq (see dwg. 9331694), Major Defect.- Five (5) springs shall be randomly selected from each heat treatment lot for this test. If any spring fails to meet the requirement, the hea

44、t treatment lot shall be rejected. 4.4.3.5 Deflection load of sprinq (see dwg. 9331694), Major Defect.- Ten (10) springs shall be randomly selected from each heat treatment lot for this test. If any spring fails to meet the requirement, the heat treatment lot shall be rejected. 4.4.3.6 Tensile stres

45、s of qasket (see dwg. 9331685), Major Defect.- Five (5) qaskets shall be randomly selected from each - lot for this test. requirement, the lot shall be rejected. If any gasket fails to meet the 4.4.3.7 Hardness of qasket (see dwg. 9331685), Major Defect.- Five (5) gaskets shall be randomly selected

46、from each lot for this test. If any gasket fails to meet the requirement, the lot shall be rejected. 4.4.3.8 Air pressure. 4.4.3.8.1 Air pressure of unpainted cover assembly (see applicable contain,er assembly dwg. (see 2.1) , Major defect.- The cover assemblies shall be checked 100 percent. If any

47、cover assembly fails to comply with the requirement, the cover assembly shall be rejected. 28 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b3LIhL 81 77777Oh 0287300 3 9 i , MIL-C-63461 (AR) 4.4.3.802 Air pressure of unpainted body assembly (body weldment) (see applicable container assembly dwg. (see 2.1) , Major defect.- The body assemblies shall be checked 100 percent. If the body assembly fails to comply with the requirement, the body assembly shall be rejected. 4.4.3.8.3