ARMY MIL-C-12927 B-1963 CARTRIDGE IGNITION M2E1 PARTS FOR LOADING ASSEMBLING AND PACKING《M2E1型子弹点火开关的装配 组装和包装》.pdf

《ARMY MIL-C-12927 B-1963 CARTRIDGE IGNITION M2E1 PARTS FOR LOADING ASSEMBLING AND PACKING《M2E1型子弹点火开关的装配 组装和包装》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-12927 B-1963 CARTRIDGE IGNITION M2E1 PARTS FOR LOADING ASSEMBLING AND PACKING《M2E1型子弹点火开关的装配 组装和包装》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-A-2550 -Amunition and Spe- cial Weapons; Gen- eral Specification for MIL-P-223 -Powder, Black MILI45208 -Inspection Require- ments, General Specification for MIL-1-45607 -Inspection Equip- ment$ Supply and Maintenance of MIGSTD-109 -Quality Assurance Terms and Defini- tions MILSTD-129 -Marking f

2、or Ship- ment and Storage MIGSTD-1235 -Single and Multi Level Continuous Sampling. Proce- dures and Tables for Inspection by Att Abu tes DRAWINGS ORDNANCE CORPS 8863425-Cartridge, Ignition, MZEI As- sembly PUBLICATIONS ORDNANCE CORPS -1EG8863425Index of Inspection (Copies of specifications, standard

3、s drawings, and publications required by suppliers in connection with specific procurement unctions should be . obtained from the procuring activity or as directed by the .contracting officer.) 2.2 Other publications. The following docu- - ment forms a part of this specification to the extent specif

4、ied herein. Unless otherwise in- dicated, the issue in effect on date of invita- tion for bids, or request for proposal, shall Equipment Lists . WPb. .- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IIL-C-12927B (MU) CODE OF FEDERAL REGULATIONS 49

5、CFR 71-90-Interstate Commerce Commission Rules and Regulations for the Transportation of Explosives and Other Dangerous Articles (The Interstate Commerce Commission Regula- tions are now a part of the Code o Federal Reg- ulations (1949 Edition and revisions) available from the Superintendent of Docu

6、ments, Government Printing Office, Wnsliington 25, D.C. Orders for the above publications should cite “49 CFR 71-90 (latest revisions) .” 3. REQUIREMENTS 3.1 Material, Materials shall be in accord- ance with applicable drawings and specifica- tions. 3.2 Cartridge assembly. The assembly shall comply

7、with all requirements specified on Drawing (dwg,) 8863426 and with all re- quirements specified in applicable specifica- tions. 3.3 Moisture content of black powder. The moisture content of the black powder at the loading station, at the time of loading, shall not exceed 0.60 percent when determined

8、 as specified in 4.3.1. 3.4 Primer Functioning Sensitivity. 3.4.1 Nonfmctioning. The primer-and body assembly shall not function under an applied energy value of 4 inch ounces minimum (min.) when tested as specified in 4.3.2.1. 3.4.2 Functzon$ng. The primer and body assembly shall function under an

9、applied en- ergy value of 1920 inch ounces maximum (max.) when tested as specified in 4.3.2.2. 3.5 Waterproofness, The loaded cartridges shall function after being completely sub- merged in water for 3 hours (see 43.3). 3.6 Workmanship, AlLparts and assemblies shall be fabricated and loaded in a tho

10、rough, worlmanlike manner. They shall be free of burrs, sharp edges, cracks, dirt, grease, blisters and other foreign matter. The clean- ing method used shall not be injurious to any part nor shall the parts be contaminated by the cleaning agent. Exterior surface coatings shall be continuous except

11、for a few light scratches not exposing base material. All required markings shall be neat and sharply defined. All packing components shall be dry. 4. QUALITY ASSURANCE PROVISIONS 4.1 General quality assurance provisions. Unless otherwise specified in the contract or purchase order the supplier is r

12、esponsible for the performance of all inspection require- ments specified herein. Except as otherwise specified, the supplier may utilize his own or any other inspection facilities and services acceptable to the Government. Inspection records of the examinations and tests shall be kept complete and

13、available to the Govern- ment as specified in the contract or order. The Government reserves the right to per- form any of the inspections set forth in the specification where such inspections are deemed necessary to assure that supplies and services conform to prescribed requirements. Reference sha

14、ll be made to Standard MIL STD-109 in order to define terms used herein. The provisions of Specification MIL-A-2650 shall apply. 4.1.1 Contractor quality assurance system. The contractor shall provide and maintain an effective quality assurance system in com- pliance with the requirements of Specifi

15、ca- tion MIL-1-45208. 4.1.2 Submission of prodztct. At the time the completed lot of product is submitted to the Government for acceptance the contrac- tor shall supply the following information accompanied by a certificate which attests that the information provided is correct and applicable to the

16、 product being submitted: (a) A statement that the lot complies with all quality assurance pro- visions of the approved current written description of the system. (b) Number of units of product in- spected. e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

17、HS-,-,-(c) Results obtained for all inspection (d) Drawing, Specification number and basis of the contractors records. assigned. In no instance will a characteristic classified “critical” be accepted solely on the performed. date, together with an identifica- tion and date of changes. 4.2 Inspection

18、 (e) Certificates of analyses on all ma- terial procured diyectly by the contractor when such material is controlled by Government specifi- cations referenced in any of the contractual documents. (f) Number of items in the lot. (9) Date submitted. The certificate shall be signed by a responsi- ble a

19、gent of the certifying organization. The initial certificate submitted shall be substanti- ated by evidence of the agents authority to bind his principal. Substantiation . of the agents authority will not be required with subsequent certificates unless, during the course of the contract, this author

20、ity is vested in another agent of the certifying organiza- tion, 4.1.3 Government verification, Using the contractors written quality assurance pro- cedure, this detail specification, the applicable drawings and other contractual documents as a guide, the Government inspector shall verify at unsched

21、uled intervals all quality assurance operations performed by the con- tractor. Verification will be in accordance with Specification MILI45208 and will be performed to the extent necessary to assure compliance with the contractual require- ments. Severity of Government inspection of individual chara

22、cteristics will be directly re- lated to the seriousness of the classification 4.2.1 Lot fovmation. A lot shall consist of cartridges produced by one manufacturer in one unchanged process, in accordance with the same drawing, same drawing revision, same specification, and same specification re- visi

23、on. Drawing, specification, and process changes not affecting safety, performance or fit, as determined by the Government shall not necessitate changing the lot interfix num- ber. Lots shall be submitted for inspection in accordance with Standard MIGSTD- 105D (or Standard MIGSTD-1235, when applicabl

24、e). Each lot shall contain: (a) Primers of one lot interfix number from one manufacturer. (b) Black powder of one lot interfix number from one manufacturer. 4.2.2 Examimt;orl. Sampling plans and procedures for the following classifications of defects shall be in accordance with Stand- ard MIL-STD-10

25、5D except that inspection. for critical defects, when listed, shall .be 100 percent. Continuous sampling plans in ac- cordance with Standard MIGSTD-1235 may be used if approved by the procuring activ- ity. Also, at the option of the piocuring ac- tivity, AQLs and sampling plans may be applied to the

26、 individual characteristics listed using an AQL of 0.25 percent for each major defect and an AQL of 0.40 percent for each minor defect. Equipment necessary for the performance of the inspections listed shall be in accordance with 4.2.4. 4.2.21 Body assembly (see dwg. 8863423 covering a detail of 886

27、3424). Categoi-ies Critical: None defined. Defects Method of Code No. inmecth (866 63) Major: 101. 102. 103. 104. 105. 201. 202. Minor : AQL 0.65 percent Diametev of flange (max.) . O1001 Outside diameter of body, max. . 01002 Knurl not 360 degrees .: . Visual 01003 Head loose visual- al-Manual 0100

28、4 Wad missing or improperly seated . :. .Visual 01005 Marking misleading or unidentifiable .Visual 01006 Cut or blister on inside of body .Visual 01007 Gage .Gage AQL 1.0 percent 8 Y - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIGG12927B (MU) 4

29、.2.2.2 Primer and body assembly (see dwg. 8863424 covering a detail of 8863425). Method of Code No. inspection Categorias Defecta Critieal : Major: AQL 0.25 percent 1. Primer above flush Straighage 02001 Primer flash hole not completely covered by lacquer Visual Primer loose or missing . Visual-Manu

30、al 02003 02002 101. 102. 201. Evidence of poor workmanship (see 3.6) 02004 Visual Minor : AQL 0.40 percent 4.2.2.3 Crimp cap (see dyg. 8863421 covering it detail of 8863426). Categories Critical ; None defined. Major: None defined. Defects Minor : AQL 1.50 percent 201. Length, mu. . ,Gage 03001 0300

31、2 202. Inside diameter Gage 203. Wall thickness, min. .Gage 03003 204. Evidence of poor workmanship (see 3.6) . ,Visual 03004 4.2.2.4 Cartridge assembly prior to crimping (see dwg. 8863425). CatogM.iee Critical: None defined. Method of Code. No. Sliaiiection Major : AQL 0.25 percent Minor : AQL 0.40

32、 percent 101. 201. Weight of charge, out of tolerance . Balance Foreign matter in charge . .visual 4.2.2.5 Cartridge assembly prior to assembling crimp cap (seedwg. 8863425) Nethod of inspection CateDOrim Defeoa Critical : 1. Major: None defined. Minor : AQL 1.50 percent Wadding slanted or damaged c

33、ausing power leakage . . . .Visual 201. 202. 203. 204. 205. Crimp roll not 360 degrees . .Visual Lacquer missing or improperly applied Visual Wadding slanted or damaged with no power leakage Visual Marking on outer wad misleading or unidentifiable . ,Visual Evidence of poor workmanship (see 3.6) . V

34、isual 4.2.2.6 Ignition cartridge assembly (see dwg. 8863425). CategoriBs Critical: None defined. DCf8Ct.S etiw of iwection Major: AQL 0;40 percent 101. 102. 103. Outside diameter at crimp cap max. ,i., .Gage Overall length, Max. . .; . .Gage Lacquer mlssing frqm end of primer .or crimp, cap . ;Visua

35、l 4. (, _-_sbl_-=- - 04001 04002 Code No. 06001 05002 05003 05004 06005 . O5006 Code No. 06001 06002 06003 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.2.3 Testing. 4.2.3.1 Moisture content of black powder (see d.d)-major defect, Code No. 04003.

36、 The contractor shall provide adequate controls to assure the compliance of each lot with the applicable requirement. The contractor shall test for verification at least one completed cartridge assembly from each eight hours production. Composite samples shall not be used in determining compliance.

37、The black powder shall be tested as specified in 4.3.1 and any failure to comply with the applicable requirement shall be cause for rejection of the eight hours production represented by the sample. 4.2.3.2 Sensitivity. 4.2.3.2.1 Nonfunctioning (see ,?4.1)-Crit IVZUrG12927B(MU) categories Defects Me

38、thod of Co ORDM-698-12. CDCF -Contractors design responsi- bility on contractor format. OD -Ordnance design. ODMU -Ordnance design, mandatory for use. CE -Commercial equipment. SCD -Specification ControI Draw- 6.3.3 Odnnnce designs. Ordnance designs are reflected on detailed drawings which completel

39、y depict all the information neces- sary for the fabrication of the item of in- spection equipment. The contractor need pro- vide no design when an Ordnance design ia listed for an item of inspection equipment. Ordnance designs fall into two basic classi- fications; mandatory and nonmandatory. When

40、an Inspection Equipment List refer- ences mandatory Ordnance designs, the contractor shall comply with, and use hese designs accordingly. The contractor may, howevei, in connection with nonmandatory designs and with the approval of the Gov- enment, design alternate inspection equip- ment or use comp

41、arable commercial equipment to facilitate his operations. Such contractor prepared designs or commercial equipment selections must be approved by the Government prior to fabrication or pro- curing of the equipment. Designs shall be submitted for approval as specified in 6.3.7. 6.3.4 Specification co

42、ntrol drawings. Speci- fication control drawings depict the mini- mum equipment requirements in outline, descriptive, diagrammatic, or pictorial form only and specify the required performance or other characteristics. Contractors must prepare detailed drawings (see 6.3.6) of their designs in support

43、 of specification con- trol drawings. These contractor prepared designs must be approved by the Govern- ing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIGG12927B (MU) fs permissible and encouraged. However, the Arsenal completion date for desig

44、n review will be based on the date of the final submis- sion of designs. 6.4 Check test for deterioration (see 6.6). If the total elapsed time between original acceptaiice of the ignition cartridge lot and the assembly of that lot into the complete round exceeds two years, or if the ignition cartrid

45、ges have been subjected to adverse conditions for any period of time since previ- ous tests, the ignition cartridges shall be sub- jected to, and must satisfactorily comply with the following tests immediately before the ignition cartridges are assembled into the complete round. 6.4.1 Ignition cartr

46、idge assembly (after re- moval of bhck powder). 6.4.1.1 Nonfunctioning. The sampling plan for this test shall be as specified in 4.2.3.2.1, The test shall be performed as specified in 4.3.2.1. 6.4.1.2 Functioning. The sampling plan for Custodian: Army-MU %T U.8. GOVERNMENT PRINTINQ OPFlCEr I864-101047/lXUl - - -., r- - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-