ANSI UL 1641-2015 UL Standard for Safety Installation and Classification of Residential Burglar Alarm Systems (Fifth Edition)《住宅防盗报警系统的安装和分类用安全性标准》.pdf

《ANSI UL 1641-2015 UL Standard for Safety Installation and Classification of Residential Burglar Alarm Systems (Fifth Edition)《住宅防盗报警系统的安装和分类用安全性标准》.pdf》由会员分享，可在线阅读，更多相关《ANSI UL 1641-2015 UL Standard for Safety Installation and Classification of Residential Burglar Alarm Systems (Fifth Edition)《住宅防盗报警系统的安装和分类用安全性标准》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1641 Installation and Classication of Residential Burglar Alarm SystemsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTE

2、D MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Installation and Classication of Residential Burglar Alarm Systems, UL 1641 Fifth Edition, Dated January 26, 2015 Summary of Topics This new edition was issued to incorporate the

3、following changes: Revisions to 7.1 for the Standards to which control units may be evaluated Revisions to 8.1.2 for removal of NFPA 74 and adding Chapter 29 of NFPA 72 Revisions to 19.4 referencing codes after verication These revised requirements are substantially in accordance with Proposal(s) on

4、 this subject dated November 7, 2014. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as i

5、s without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings,

6、 loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardle

7、ss of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced

8、while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the a

9、ffected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. JANUARY 26, 2015 UL 1641 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION

10、 WITHOUT PERMISSION FROM UL JANUARY 26, 2015 UL 1641 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JANUARY 26, 2015 1 UL 1641 Standard for Installation and Classication of Residential Burglar Alarm Systems First Edi

11、tion April, 1983 Second Edition April, 1989 Third Edition September, 1994 Fourth Edition February, 1999 Fifth Edition January 26, 2015 This ANSI/UL Standard for Safety consists of the Fifth Edition. The most recent designation of ANSI/UL 1641 as an American National Standard (ANSI) occurred on Janua

12、ry 26, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-

13、Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain t

14、he sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 1641-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JANUARY 26, 2015 UL 1641 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FU

15、RTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 Components 4 3 Units of Measurement .5 4 Undated References 5 5 Glossary .5 6 Overall Requirements .7 7 Control Units .7 EXTENT OF PROTECTION FOR RESIDENTIAL ALARMS 8 General 8 8.1 Details 8 8.2 Basic pr

16、otection 8 8.3 Expanded protection 8 9 Wiring .9 9.1 General .9 9.2 Running and fastening 9 9.3 Splices and connections .10 9.4 Connectors .10 9.5 Entrance to building and remote areas .10 10 Windows .10 11 Doors and Other Openings 11 12 Air Conditioners, Exhaust Fans, and Similar Units 12 13 Screen

17、s .13 14 Floor Mats .13 15 Intrusion Detection Devices 13 15.1 General .13 15.2 Photoelectric units 13 15.3 Motion detection units 14 15.4 Sound and vibration units .14 16 Shunts 14 17 Control Unit 14 INTERPRETATIONS 18 General 14 MAINTENANCE AND SERVICE 19 General 21 JANUARY 26, 2015 UL 1641 3UL CO

18、PYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements apply to the installation of alarm protection products and devices connected to form a residential burglar alarm system. 1.2 These requirements include th

19、e criteria for classifying the extent of alarm protection at an individual residence as either basic protection or expanded protection. 1.3 A residential burglar alarm system may or may not have a remote connection to a central station, proprietary station, residential monitoring station, or police

20、station. If there is a remote connection, the signal receiving location shall comply with the requirements in the following standards, as applicable: a) The Standard for Central-Station Alarm Services, UL 827; b) The Standard for Proprietary Burglar Alarm Units and Systems, UL 1076; and c) The Stand

21、ard for Police Station Connected Burglar Alarm Units and Systems, UL 365. 1.4 Alarm systems covered by these requirements have a sounding device that may be mounted indoors or outdoors. 1.5 These systems comply with the requirements for Class 2 remote-control and signal circuits as dened by Article

22、725 of the National Electrical Code, NFPA 70. Systems using both re and burglary protection operate as dened by Article 760 of the National Electrical Code, NFPA 70. 1.6 The requirements assume that standard telephone operating practices may be used for leased or other lines connecting to a police o

23、r central station as dened by Article 800 of the National Electrical Code, NFPA 70. 2 Components 2.1 Except as indicated in 2.2, a component of a product covered by this standard shall comply with the requirements for that component. 2.2 A component is not required to comply with a specic requiremen

24、t that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.3 A component shall be used in accordance with its rating established for the intended conditions of use.

25、 JANUARY 26, 2015 UL 1641 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited condi

26、tions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.5 Components of a residential alarm system shall comply with the requirements for those components, and shall not be modied before, during, or after installation into the system.

27、 3 Units of Measurement 3.1 When a value for measurement is followed by a value in other units in parentheses, the rst stated value is the requirement. 4 Undated References 4.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referrin

28、g to the latest edition of that code or standard. 5 Glossary 5.1 For the purpose of this standard the following denitions apply. 5.2 ALARM PROTECTION Equipment and wiring that is installed to provide protection within an alarm system. 5.3 AREA, INACCESSIBLE An area in which people can not freely mov

29、e about, such as crawl spaces and the like. 5.4 BOUNDARY, PHYSICAL A barrier, such as a wall, ceiling, oor, partition, window, or door, that encloses the protected area. 5.5 COMBINATION SYSTEM An alarm system that provides both burglary and re protection. The alarm system may also provide additional

30、 supervisory circuits, such as medical alert, police call, basement ooding and the like. 5.6 CONTACT A device installed on a movable opening complying with the Standard for Connectors and Switches for Use with Burglar-Alarm Systems, UL 634, and that initiates an alarm. 5.7 INTRUSION DETECTION DEVICE

31、 An acoustic or shock type glass breakage detector, photoelectric beam, sound detector, vibration detector, or motion detector complying with the Standard for Intrusion-Detection Units, UL 639, designed to detect the penetration or attempted penetration of an intruder through the perimeter of the pr

32、emise, or the presence, movement, sound or other activity of an intruder within the premise. 5.8 LACING A single circuit of ne wire or foil applied to a door or similar surface in continuous parallel strips, a maximum of 4 inches (102 mm) center-to-center and covered to provide mechanical protection

33、. JANUARY 26, 2015 UL 1641 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5.9 MAINTENANCE Repair service and inspections at prescribed intervals that are intended to keep the burglar alarm system and all installed equipment in a fully oper

34、ative condition. 5.10 OPENING A point at which entry can be gained through an aperture of manhole size without cutting or tearing down any part of the building structure. An opening can be xed or movable. 5.11 OPENING, ACCESSIBLE An opening that does not comply with the requirements for an inaccessi

35、ble opening. 5.12 OPENING, INACCESSIBLE An opening: a) More than 12 feet (3.7 m) above either the ground or any projection from the same building, adjoining building or both; b) More than 12 feet away from a directly or diagonally opposite window, re escape, or roof; or c) More than 3 feet (0.9 m) a

36、way from an opening, re escape, xed object, and the like, that is in or projecting from the same or adjacent wall and that leads to other premises. See Interpretations, General, Section 18. 5.13 OPENING, MANHOLE SIZE An opening with a clear cross-section area of 96 square inches (619 cm 2 ) or more,

37、 and with the smallest dimension exceeding 6 inches (152 mm). 5.14 PROTECTION OF AN OPENING, COMPLETE Alarm protection applied to a xed or movable opening, plus contacts installed on a movable opening. A screen over an opening is considered complete protection of an opening. See also 15.4.1. 5.15 PR

38、OTECTION OF AN OPENING, PARTIAL Contacts installed on a movable opening; or an intrusion detection device installed so as to detect entry through the opening. See also 15.4.1. 5.16 RESIDENCE Any dwelling in which people reside. 5.17 RESIDENTIAL ALARM A burglar alarm system used in a residence with o

39、r without a re or supervisory alarm. 5.18 SCREEN A fully framed assembly of grooved-wood dowels having ne wire secured in the grooves, or window screen with the circuit wire secured to the mesh and frame, and complying with the Standard for Linings and Screens for Use with Burglar-Alarm Systems, UL

40、606. 5.19 SERVICE CENTER A location that may be separate from the alarm service companys main business location providing installation, maintenance, and repair service to systems served by the company. The service center is to keep maintenance records for the systems that it serves unless the record

41、s can be accessed from another location. 5.20 SERVICE VEHICLE A vehicle that is used to provide installation, maintenance, and repair service to systems served by the company. JANUARY 26, 2015 UL 1641 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION

42、 FROM UL 5.21 SOUNDING DEVICE An audible signal appliance used to signal unauthorized entry into a protected area. 5.22 TRAP A conductor or device fastened between a building structure and a screen, stripping, foiled or wired panel, fan, air conditioner, or similar device so that the two cannot be s

43、eparated without initiating an alarm. 5.23 WIRE, FINE Bare, hard-drawn, solid copper wire not larger than 24 AWG (0.21 mm 2 ) or insulated solid copper wire not larger than 26 AWG (0.13 mm 2 ) or the equivalent, used for alarm protection. 5.24 WIRING, INTERCONNECTING Those conductors used to interco

44、nnect protective devices in a burglar alarm system. 6 Overall Requirements 6.1 The area protected by a residential alarm shall be provided with a complete physical boundary. 6.2 A sounding device is required, and if mounted outdoors shall be investigated to determine if the device is acceptable for

45、outdoor use. 7 Control Units 7.1 A control unit used in a residential burglar alarm system shall comply with the control unit requirements in one or more of the following: a) The Standard for Police Station Connected Burglar Alarm Units and Systems, UL 365; b) The Standard for Local Burglar Alarm Un

46、its and Systems, UL 609; c) The Standard for Household Burglar-Alarm System Units, UL 1023; d) The Standard for Proprietary Burglar Alarm Units and Systems, UL 1076; e) The Standard for Central-Station Burglar-Alarm Units, UL 1610; f) The Standard for Digital Alarm Communicator System Units, UL 1635

47、; or g) The Control Panel Standard-Features for False Alarm Reduction, SIA CP-01. JANUARY 26, 2015 UL 1641 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL EXTENT OF PROTECTION FOR RESIDENTIAL ALARMS 8 General 8.1 Details 8.1.1 An individual

48、 alarm system protecting an entire residence or a portion thereof shall be identied as expanded or basic (see 8.2.1 and 8.3.1). The alarm system may or may not include re or supervisory alarm protection. 8.1.2 The re protection portion of a combination system shall comply with the requirements of Ch

49、apter 29 of the National Fire Alarm and Signaling Code, NFPA 72. 8.2 Basic protection 8.2.1 Basic protection shall consist of: a) Contacts on all movable accessible openings; or b) Contacts on all accessible exterior doors and: 1) A motion detection device in one or more selected areas; 2) A photoelectric beam or motion detector across one or more hallways, stairways, rooms, or the like; 3) A oor mat in one or more selected areas, such as a hallway, sta