书签分享收藏举报版权申诉 / 39

立即下载加入VIP,交流精品资源

当前位置：首页 > 标准规范 > 国际标准 > ANSI > ANSI ASME B16.11-2016 Forged Fittings Socket-Welding and Threaded (Includes Errata June 2017).pdf

ANSI ASME B16.11-2016 Forged Fittings Socket-Welding and Threaded (Includes Errata June 2017).pdf

上传人：boatfragile160

文档编号：431698

上传时间：2018-11-11

格式：PDF

页数：39

大小：727.33KB

《ANSI ASME B16.11-2016 Forged Fittings Socket-Welding and Threaded (Includes Errata June 2017).pdf》由会员分享，可在线阅读，更多相关《ANSI ASME B16.11-2016 Forged Fittings Socket-Welding and Threaded (Includes Errata June 2017).pdf（39页珍藏版）》请在麦多课文档分享上搜索。

1、AN AMERICAN NATIONAL STANDARD ASME B16.11-2016 (Revision of ASME B16.11-2011) Forged Fittings, Socket-Welding and ThreadedErrata to ASME B16.11-2016 Forged Fittings, Socket-Welding and Threaded The errata corrections listed below apply to ASME B16.11-2016. Corrected entries in the Tables are shown i

2、n bold for the users convenience. Page Location Change 3 Table 2 (1) For Nominal Pipe Size 1, entry for “End-to-End Couplet, M” corrected to “42.9” (2) For Nominal Pipe Size 1, entry for “Weld Ring Diameter, N” corrected to “33.4” 6 Table 5 (1) For Nominal Pipe Size 3 8 , entry for “End-to-End Coupl

3、ing, W” corrected to “38” (2) For Nominal Pipe Size 3 8 , entry for “End-to-End Caps, P” for 3000 corrected to “25” (3) For Nominal Pipe Size 3, entry for “Weld Ring Diameter, N” corrected to “88.9” (4) Reference to Table 2 corrected in General Note (b) 12 Table I-1 For Nominal Pipe Size 3 4 , entry

4、 for “Body Wall, G” for 3000 Min. corrected to “0.154” 13 Table I-2 For Nominal Pipe Size 1 4 , entry for “Socket Wall Thickness, C” for 3000 Avg. corrected to “0.149” 16 Table I-5 (1) For Nominal Pipe Size 3, entry for “Outside Diameter, D” for 3000 corrected to “4.25” (2) In General Note (a), mill

5、imeters corrected to read “inches” THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Two Park Avenue, New York, NY 10016-5990 June 2017Table 2 Socket-Welding Couplings, Bosses, Caps, and Couplets Nominal Pipe Size Socket Bore Dia., B Bore Diameter of Fittings, D Socket Wall Thickness, Note (1), C Outside

6、 Dia. Couplet, G Tol. Socket Depth, J Laying Lgth., E Tol. Laying Lgth., F Tol. End Wall Thickness, K End-to-End Couplet, M Weld Ring Diameter, N Weld Ring Length, Q Tol. 3000 6000 9000 3000 6000 9000 3000 6000 9000 Tol. Tol. Max. Min. Max. Min. Max. Min. Max. Min. Avg. Min. Avg. Min. Avg. Min. 3000

7、 6000 Min. Min. Min. Min. 3000/ 6000 1 8 11.2 10.8 7.6 6.1 4.8 3.2 3.18 3.18 3.96 3.43 1.5/0.0 9.5 6.5 1.5 16.0 1.5 4.8 6.4 1 4 14.6 14.2 10.0 8.5 7.1 5.6 3.78 3.30 4.60 4.01 23.8 25.4 1.5/0.0 9.5 6.5 1.5 16.0 1.5 4.8 6.4 30.2 0.8/0.0 17.5 1.5/0.0 9.5 0.8 3 8 18.0 17.6 13.3 11.8 9.9 8.4 4.01 3.50 5.

8、03 4.37 27.0 31.8 1.5/0.0 9.5 6.5 3.0 17.5 3.0 4.8 6.4 30.2 0.8/0.0 20.7 1.5/0.0 9.5 0.8 1 2 22.2 21.8 16.6 15.0 12.5 11.0 7.2 5.6 4.67 4.09 5.97 5.18 9.35 8.18 33.4 38.1 1.5/0.0 9.5 9.5 3.0 22.5 3.0 6.4 7.9 11.2 33.4 0.8/0.0 23.8 1.5/0.0 9.5 0.8 3 4 27.6 27.2 21.7 20.2 16.3 14.8 11.8 10.3 4.90 4.27

9、 6.96 6.04 9.78 8.56 38.1 44.5 1.5/0.0 12.5 9.5 3.0 24.0 3.0 6.4 7.9 12.7 34.9 0.8/0.0 27.0 1.5/0.0 9.5 0.8 1 34.3 33.9 27.4 25.9 21.5 19.9 16.0 14.4 5.69 4.98 7.92 6.93 11.38 9.96 46.1 57.2 1.5/0.0 12.5 12.5 4.0 28.5 4.0 9.6 11.2 14.2 42.9 0.8/0.0 33.4 1.5/0.0 9.5 0.8 1 1 4 43.1 42.7 35.8 34.3 30.2

10、 28.7 23.5 22.0 6.07 5.28 7.92 6.93 12.14 10.62 55.6 63.5 1.5/0.0 12.5 12.5 4.0 30.0 4.0 9.6 11.2 14.2 47.6 0.8/0.0 42.9 1.5/0.0 9.5 0.8 1 1 2 49.2 48.8 41.6 40.1 34.7 33.2 28.7 27.2 6.35 5.54 8.92 7.80 12.70 11.12 63.5 76.2 1.5/0.0 12.5 12.5 4.0 32.0 4.0 11.2 12.7 15.7 50.8 0.8/0.0 49.2 1.5/0.0 9.5

11、 0.8 2 61.7 61.2 53.3 51.7 43.6 42.1 38.9 37.4 6.93 6.04 10.92 9.50 13.84 12.21 79.4 92.1 1.5/0.0 16.0 19.0 4.0 41.0 4.0 12.7 15.7 19.0 57.2 1.5/0.0 61.9 1.5/0.0 9.5 0.8 2 1 2 74.4 73.9 64.2 61.2 8.76 7.67 92.1 108.0 1.5/0.0 16.0 19.0 5.0 43.0 5.0 15.7 19.0 63.5 1.5/0.0 73.0 1.5/0.0 9.5 0.8 3 90.3 8

12、9.8 79.4 76.4 9.52 8.30 111.1 127.0 1.5/0.0 16.0 19.0 5.0 44.5 5.0 19.0 22.4 69.9 1.5/0.0 88.9 1.5/0.0 9.5 0.8 4 115.7 115.2 103.8 100.7 10.69 9.35 141.3 158.8 1.5/0.0 19.0 19.0 5.0 48.0 5.0 22.4 28.4 76.2 1.5/0.0 114.3 1.5/0.0 9.5 0.8 GENERAL NOTE: Dimensions are in millimeters. NOTE: (1) Average o

13、f socket wall thickness around periphery shall not be less than listed values. The minimum values are permitted in localized areas.Table 5 Threaded Couplings, Bosses, Caps, and Couplets Nominal Pipe Size Outside Diameter, D Outside Diameter Couplet, E Tol. End-to- End Coupling, W End-to-End Caps, P

14、End-to-End Coupling, M Tol. Minimum End Wall Thickness, G Weld Ring Length, Q Tol. Weld Ring Diameter, N Tol. Minimum Length of Thread Note (1) 3000 6000 3000 6000 3000/ 6000 3000 6000 3000/ 6000 3000 6000 3000/ 6000 3000/ 6000 3000/6000 B L 2 1 8 16 22 32 19 22 4.8 6.4 6.4 6.7 1 4 19 25 23.8 25.4 1

15、.5/0.0 35 25 27 30.2 0.8/0.0 4.8 6.4 9.5 0.8 17.5 1.5/0.0 8.1 10.2 3 8 22 32 27.0 31.8 1.5/0.0 38 25 27 30.2 0.8/0.0 4.8 6.4 9.5 0.8 20.7 1.5/0.0 9.1 10.4 1 2 28 38 33.4 38.1 1.5/0.0 48 32 33 33.4 0.8/0.0 6.4 7.9 9.5 0.8 23.8 1.5/0.0 10.9 13.6 3 4 35 44 38.1 44.5 1.5/0.0 51 37 38 34.9 0.8/0.0 6.4 7.

16、9 9.5 0.8 27.0 1.5/0.0 12.7 13.9 1 44 57 46.1 57.2 1.5/0.0 60 41 43 42.9 0.8/0.0 9.7 11.2 9.5 0.8 33.4 1.5/0.0 14.7 17.3 1 1 4 57 64 55.6 63.5 1.5/0.0 67 44 46 47.6 0.8/0.0 9.7 11.2 9.5 0.8 42.9 1.5/0.0 17.0 18.4 1 1 2 64 76 63.5 76.2 1.5/0.0 79 44 48 50.8 0.8/0.0 11.2 12.7 9.5 0.8 49.2 1.5/0.0 17.8

17、 18.4 2 76 92 79.4 79.4 1.5/0.0 86 48 51 57.2 1.5/0.0 12.7 15.7 9.5 0.8 61.9 1.5/0.0 19.0 19.2 2 1 2 92 108 92.1 92.1 1.5/0.0 92 60 64 63.5 1.5/0.0 15.7 19.0 9.5 0.8 73.0 1.5/0.0 23.6 28.9 3 108 127 111.1 111.1 1.5/0.0 108 65 68 69.9 1.5/0.0 19.0 22.4 9.5 0.8 88.9 1.5/0.0 25.9 30.5 4 140 159 141.3 1

18、41.3 1.5/0.0 121 68 75 76.2 1.5/0.0 22.4 28.4 9.5 0.8 114.3 1.5/0.0 27.7 33.0 GENERAL NOTES: (a) Dimensions are in millimeters. (b) The wall thickness away from the threaded ends shall meet the minimum wall thickness requirements of Table 2 for the appropriate NPS and Class Designation fitting. NOTE

19、: (1) Dimension B is minimum length of perfect thread. The length of useful thread (B plus threads with fully formed roots and flat crests) shall not be less than L 2 (effective length of external thread) required by American National Standard for Pipe Threads (ASME B1.20.1; see para. 6.3).Table I-1

20、 Socket-Welding Elbows, Tees, and Crosses Nominal Pipe Size Socket Bore Dia., B Bore Diameter of Fittings, D Socket Wall Thickness, Note (1), C Body Wall, G Socket Depth, J Center-to-Bottom of Socket, A 3000 6000 9000 3000 6000 9000 3000 6000 9000 90 Elbows, Tees, and Crosses 45deg Elbow Tol. Max. M

21、in. Max. Min. Max. Min. Max. Min. Avg. Min. Avg. Min. Avg. Min. Min. Min. Min. Min. 3000 6000 9000 3000 6000 9000 1 8 0.440 0.420 0.299 0.239 0.189 0.126 0.125 0.125 0.156 0.135 0.095 0.124 0.380 0.440 0.440 0.310 0.310 0.030 1 4 0.575 0.555 0.394 0.334 0.280 0.220 0.149 0.130 0.181 0.158 0.119 0.14

22、5 0.380 0.440 0.530 0.310 0.310 0.030 3 8 0.710 0.690 0.523 0.463 0.389 0.329 0.158 0.138 0.198 0.172 0.126 0.158 0.380 0.530 0.620 0.310 0.440 0.060 1 2 0.875 0.855 0.652 0.592 0.494 0.434 0.282 0.222 0.184 0.161 0.235 0.204 0.368 0.322 0.147 0.188 0.294 0.380 0.620 0.750 1.000 0.440 0.500 0.620 0.

23、060 3 4 1.085 1.065 0.854 0.794 0.642 0.582 0.464 0.404 0.193 0.168 0.274 0.238 0.385 0.337 0.154 0.219 0.308 0.500 0.750 0.880 1.120 0.500 0.560 0.750 0.060 1 1.350 1.330 1.079 1.019 0.845 0.785 0.629 0.569 0.224 0.196 0.312 0.273 0.448 0.392 0.179 0.250 0.358 0.500 0.880 1.060 1.250 0.560 0.690 0.

24、810 0.080 1 1 4 1.695 1.675 1.410 1.350 1.190 1.130 0.926 0.866 0.239 0.208 0.312 0.273 0.478 0.418 0.191 0.250 0.382 0.500 1.060 1.250 1.380 0.690 0.810 0.880 0.080 1 1 2 1.935 1.915 1.640 1.580 1.368 1.308 1.130 1.070 0.250 0.218 0.351 0.307 0.500 0.438 0.200 0.281 0.400 0.500 1.250 1.500 1.500 0.

25、810 1.000 1.000 0.080 2 2.426 2.406 2.097 2.037 1.717 1.657 1.533 1.473 0.273 0.238 0.430 0.374 0.545 0.477 0.218 0.344 0.436 0.620 1.500 1.620 2.120 1.000 1.120 1.120 0.080 2 1 2 2.931 2.906 2.529 2.409 0.345 0.302 0.276 0.620 1.620 1.120 0.100 3 3.560 3.535 3.128 3.008 0.375 0.327 0.300 0.620 2.25

26、0 1.250 0.100 4 4.570 4.545 4.086 3.966 0.421 0.368 0.337 0.750 2.620 1.620 0.100 GENERAL NOTE: Dimensions are in inches. NOTE: (1) Average of socket wall thickness around periphery shall not be less than listed values. The minimum values are permitted in localized areas.Table I-2 Socket-Welding Cou

27、plings, Bosses, Caps, and Couplets Nominal Pipe Size Socket Bore Dia., B Bore Diameter of Fittings, D Socket Wall Thickness, Note (1), C Outside Dia. Couplet, G Tol. Socket Depth, J Laying Lgth., E Tol. Laying Lgth., F Tol. End Wall Thickness, K End to End Couplet, M Weld Ring Diameter, N Weld Ring

28、Length, Q Tol. 3000 6000 9000 3000 6000 9000 3000 6000 9000 Tol. Tol. Max. Min. Max. Min. Max. Min. Max. Min. Avg. Min. Avg. Min. Avg. Min. 3000 6000 Min. Min. Min. Min. 3000/ 6000 1 8 0.440 0.420 0.299 0.239 0.189 0.126 0.125 0.125 0.156 0.135 +0.06/ 0.00 0.38 0.25 0.06 0.62 0.03 0.19 0.25 1 4 0.57

29、5 0.555 0.394 0.334 0.280 0.220 0.149 0.130 0.181 0.158 0.94 1.00 +0.06/ 0.00 0.38 0.25 0.06 0.62 0.03 0.19 0.25 1.19 +0.030/ 0.000 0.688 +0.060/ 0.000 0.375 0.03 3 8 0.710 0.690 0.523 0.463 0.389 0.329 0.158 0.138 0.198 0.172 1.06 1.25 +0.06/ 0.00 0.38 0.25 0.12 0.69 0.06 0.19 0.25 1.19 +0.030/ 0.0

30、00 0.813 +0.060/ 0.000 0.375 0.03 1 2 0.875 0.855 0.652 0.592 0.494 0.434 0.282 0.222 0.184 0.161 0.235 0.204 0.368 0.322 1.31 1.50 +0.06/ 0.00 0.38 0.38 0.12 0.88 0.06 0.25 0.31 0.44 1.31 +0.030/ 0.000 0.938 +0.060/ 0.000 0.375 0.03 3 4 1.085 1.065 0.854 0.794 0.642 0.582 0.464 0.404 0.193 0.168 0.

31、274 0.238 0.385 0.337 1.50 1.75 +0.06/ 0.00 0.50 0.38 0.12 0.94 0.06 0.25 0.31 0.50 1.38 +0.030/ 0.000 1.063 +0.060/ 0.000 0.375 0.03 1 1.350 1.330 1.079 1.019 0.845 0.785 0.629 0.569 0.224 0.196 0.312 0.273 0.448 0.392 1.81 2.25 +0.06/ 0.00 0.50 0.50 0.16 1.12 0.08 0.38 0.44 0.56 1.69 +0.030/ 0.000

32、 1.313 +0.060/ 0.000 0.375 0.03 1 1 4 1.695 1.675 1.410 1.350 1.190 1.130 0.926 0.866 0.239 0.208 0.312 0.273 0.478 0.418 2.19 2.50 +0.06/ 0.00 0.50 0.50 0.16 1.19 0.08 0.38 0.44 0.56 1.88 +0.030/ 0.000 1.688 +0.060/ 0.000 0.375 0.03 1 1 2 1.935 1.915 1.640 1.580 1.368 1.308 1.130 1.070 0.250 0.218

33、0.351 0.307 0.500 0.438 2.50 3.00 +0.06/ 0.00 0.50 0.50 0.16 1.25 0.08 0.44 0.50 0.62 2.00 +0.030/ 0.000 1.938 +0.060/ 0.000 0.375 0.03 2 2.426 2.406 2.097 2.037 1.717 1.657 1.533 1.473 0.273 0.238 0.430 0.374 0.545 0.477 3.13 3.63 +0.06/ 0.00 0.62 0.75 0.16 1.62 0.08 0.50 0.62 0.75 2.25 +0.060/ 0.0

34、00 2.438 +0.060/ 0.000 0.375 0.03 2 1 2 2.931 2.906 2.529 2.409 0.345 0.302 3.63 4.25 +0.06/ 0.00 0.62 0.75 0.20 1.69 0.10 0.62 0.75 2.50 +0.060/ 0.000 2.875 +0.060/ 0.000 0.375 0.03 3 3.560 3.535 3.128 3.008 0.375 0.327 4.38 5.00 +0.06/ 0.00 0.62 0.75 0.20 1.75 0.10 0.75 0.88 2.75 +0.060/ 0.000 3.5

35、00 +0.060/ 0.000 0.375 0.03 4 4.570 4.545 4.086 3.966 0.421 0.368 5.56 6.25 +0.06/ 0.00 0.75 0.75 0.20 1.88 0.10 0.88 1.12 3.00 +0.060/ 0.000 4.500 +0.060/ 0.000 0.375 0.03 GENERAL NOTE: Dimensions are in inches. NOTE: (1) Average of socket wall thickness around periphery shall not be less than list

36、ed values. The minimum values are permitted in localized areas.Table I-5 Threaded Couplings, Bosses, Caps, and Couplets Nominal Pipe Size Outside Diameter, D Outside Diameter Couplet, E Tol. End-to- End Coupling, W End-to- End Caps, P End-to-End Coupling, M Tol. Minimum End Wall Thickness, G Weld Ri

37、ng Length, Q Tol. Weld Ring Diameter, N Tol. Minimum Length of Thread Note (1) 3000 6000 3000 6000 3000/ 6000 3000 6000 3000/ 6000 3000 6000 3000/ 6000 3000/ 6000 3000/6000 B L 2 1 8 0.62 0.88 1.25 0.75 0.88 0.19 0.25 0.25 0.2639 1 4 0.75 1.00 0.928 1.000 +0.06/0.00 1.38 1.00 1.06 1.188 +0.03/0.00 0

38、.19 0.25 0.375 0.03 0.688 +0.06/0.00 0.32 0.4018 3 8 0.88 1.25 1.063 1.250 +0.06/0.00 1.50 1.00 1.06 1.188 +0.03/0.00 0.19 0.25 0.375 0.03 0.813 +0.06/0.00 0.36 0.4078 1 2 1.12 1.50 1.313 1.500 +0.06/0.00 1.88 1.25 1.31 1.313 +0.03/0.00 0.25 0.31 0.375 0.03 0.938 +0.06/0.00 0.43 0.5337 3 4 1.38 1.75

39、 1.500 1.750 +0.06/0.00 2.00 1.44 1.50 1.375 +0.03/0.00 0.25 0.31 0.375 0.03 1.063 +0.06/0.00 0.50 0.5457 1 1.75 2.25 1.813 2.250 +0.06/0.00 2.38 1.62 1.69 1.688 +0.03/0.00 0.38 0.44 0.375 0.03 1.313 +0.06/0.00 0.58 0.6828 1 1 4 2.25 2.50 2.188 2.500 +0.06/0.00 2.62 1.75 1.81 1.875 +0.03/0.00 0.38 0

40、.44 0.375 0.03 1.688 +0.06/0.00 0.67 0.7068 1 1 2 2.50 3.00 2.500 3.000 +0.06/0.00 3.12 1.75 1.88 2.000 +0.03/0.00 0.44 0.50 0.375 0.03 1.938 +0.06/0.00 0.70 0.7235 2 3.00 3.62 3.125 3.625 +0.06/0.00 3.38 1.88 2.00 2.250 +0.06/0.00 0.50 0.62 0.375 0.03 2.438 +0.06/0.00 0.75 0.7565 2 1 2 3.62 4.25 3.

41、625 4.250 +0.06/0.00 3.62 2.38 2.50 2.500 +0.06/0.00 0.62 0.75 0.375 0.03 2.875 +0.06/0.00 0.93 1.1380 3 4.25 5.00 4.375 5.000 +0.06/0.00 4.25 2.56 2.69 2.750 +0.06/0.00 0.75 0.88 0.375 0.03 3.500 +0.06/0.00 1.02 1.2000 4 5.50 6.25 5.563 6.250 +0.06/0.00 4.75 2.69 2.94 3.000 +0.06/0.00 0.88 1.12 0.3

42、75 0.03 4.500 +0.06/0.00 1.09 1.3000 GENERAL NOTES: (a) Dimensions are in inches. (b) The wall thickness away from the threaded ends shall meet the minimum wall thickness requirements of Table I-2 for the appropriate NPS and Class Designation fitting. NOTE: (1) Dimension B is minimum length of perfe

43、ct thread. The length of useful thread (B plus threads with fully formed roots and flat crests) shall be less than L 2 (effective length of external thread) required by American National Standard for Pipe Threads (ASME B1.20.1; see para. 6.3).ASME B16.11-2016 (Revision of ASME B16.11-2011) Forged Fi

44、ttings, Socket-Welding and Threaded AN AMERICAN NATIONAL STANDARD xDate of Issuance: January 20, 2017 The next edition of this Standard is scheduled for publication in 2021. ASME issues writt en replies to inquiries concerning interpre tations of technical aspects of this Standard. Periodically cert

45、ain actions of the ASME B16 Committ ee may be published as Cases. Cases and interpre tations are published on the ASME Web site under the Committ ee Pages at htt p:/cstools.asme.org/ as they are issued. Errata to codes and s tandards may be post ed on the ASME Web site under the Committ ee Pages to

46、pr ovide corrections to incorrectly published item s, or to correct typographical or grammatical err ors in codes and s tandards. Such errata shall be used on the date post ed. The Committ ee Pages can be found at htt p:/cstools.asme.org/. There is an option available to automatically receive an e-m

47、ail notification when errata are post ed to a particular code or sta ndard. This option can be found on the appr opriate Committ ee Page after selecting “Errata” in the “Publication Information” section. ASME is the regis tered trademark of The American Society of Mechanical Engineers. This code or standard was developed under proc edures accredited as meeting the criteria for American National Standards. The Standards Commit tee that approved the code or standard was balanced to assure tha

下载提示：本站仅提供存储空间/不修改/不编辑

1.请仔细阅读文档，确保文档完整性，对于不预览、不比对内容而直接下载带来的问题本站不予受理。
2.下载的文档，不会出现我们的网址水印。
3、该文档所得收入（下载+内容+预览）归上传者、原创作者；如果您是本文档原作者，请点此认领！既往收益都归您。

同意并开始全文预览

文档包含非法信息？点此举报后获取现金奖励！

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

5000 积分 0人已下载

下载	加入VIP,交流精品资源

版权申诉 word格式文档无特别注明外均可编辑修改；预览文档经过压缩，下载后原文更清晰！ 立即下载

配套讲稿：: 如PPT文件的首页显示word图标，表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
特殊限制：: 部分文档作品中含有的国旗、国徽等图片，仅作为作品整体效果示例展示，禁止商用。设计者仅对作品中独创性部分享有著作权。
关键词：: ANSIASMEB16112016FORGEDFITTINGSSOCKETWELDINGANDTHREADEDINCLUDESERRATAJUNE2017PDF

麦多课文档分享所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。

关于本文

本文标题：ANSI ASME B16.11-2016 Forged Fittings Socket-Welding and Threaded (Includes Errata June 2017).pdf
链接地址：http://www.mydoc123.com/p-431698.html