AIR FORCE MIL-J-25718 B-1969 JUG INSULATED TYPE CNU-2 C《CNU-2 C型隔热罐》.pdf

《AIR FORCE MIL-J-25718 B-1969 JUG INSULATED TYPE CNU-2 C《CNU-2 C型隔热罐》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-J-25718 B-1969 JUG INSULATED TYPE CNU-2 C《CNU-2 C型隔热罐》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-J-257l8B(USAF) .4 November 1969 SUPERSEDING .-. MIL-J-257 approval involves testing and evaluating the first article for conformance with the requirements herein before, or in the initial stage of, production under a contract. Approval of the first article shall not relieve the supplier of the r

2、esponsibility to furnish equipment in accordance with the requirements of this specification. 3.2 Design. The jug shall be designed to conform to Figure 1. It shall consist of an inner and outer case to form the body. cases shall be filled with insulation to provide the proper heat retention charact

3、eristics. The entire assembly shall provide for maximum sanitation and ease of cleaning. be held to a minimum. liquids, internal radii shall be a minimum of 3/16 inch. shall have a removabe cover or lid that has a carrying handle. shall be provided for draining the contents. Contamhation of the cont

4、ents by foreign materials collecting on %op of the container body shall be mini- mized-by either sloping the top of the jug from the inner periphery to the The space between the The total number and length of joints and radii shall Where necessary and where normally in contact with The top of the ju

5、g A spigot 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-25718B 73 777770b 0458013 O U MIL- J- 2 57l8B ( USAF) outer periphery or by a. cover and gasket which are both sufficiently large enough to cover the entire top of the container body.

6、 equipped with thermostatically controlled, electrical heating elements. The design shall permit, where possible, disassembly, reassembly, and service maintenance by tools and maintenance equipment normally available as ccmmer- ciai standards. Special and commercial standard tools are defined in MIL

7、-S- 8512. The jug shall be 3.2.1 Capacity. lons. The jug shall have a minimum internal capacity of two gal- 3.2.2 Weight. The weight ofthe complete jug, including the heating elements, shall not exceed 16 pounds. 3.2.3 Interchangeability. All parts having the same manufacturer*s part nuniber shall b

8、e functionally and dimensionally interchangeable. All parts shall be manufactured to such standards as will permit replacement without modification of parts or equipnent. 3.2.4 Material. specified for each component, shall be new, and of the quality necessary to meet the requirements specified herei

9、n. All material used in the manufacture of the jug shall be as 3.2.5 Threads. All threaded parts Shan be in the inch system and shall con- form to Handbook 1128. 3.3 Construction. The jug shall be complete and ready for use when connected to a suitable source of power. The jug shall be fabricated of

10、 parts which are sound and free from repair. Joints, where necessary, shall be smooth, even, and made by inert gas shielded arc welding in accordance witin MIL-W-8611. 3.3.1 Fasteniw devices. Al1 screws, pins, and similar parts shall be in- stalled with means to prevent loss of tightness. adjustment

11、 shall not be swaged, peened, or otherwise permanently deformed. 3.3.2 Dissimilar metals. Dissimilar metals shall not be used in intimate contact with each other unless suitably protected against electrolytic cor- rosion. 3.3.3 Surfaces. finish. standard polish No. 4 or No. 6 of QQ-S-766. 3.4 Compon

12、ents. body, cover, spigot, insulation and electrical equipment to meet the require- ants specified herein. Defective parts shall not be reclaimed for use. Those subject to removal or Dissimilar metals are defined in MS33586. The inner case of the jug shall have an electro-polish The outer case and c

13、over shall have an electro-polish finish or The insulated jug shall consisi essentially of a container 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-257186 73 W 7777706 0458044 2 = MIL- J -2 5 7 18B (USAF) 3.4.1 Container body. The inner an

14、d outer cases shall be fabricated of not less than 0.025 inch thick corrosion-resistant steel conforming to class 201, 202, 301, 302, or 304, condition A of C.Q-S-766. The sides of the outer case shall be reinforced by stiffening ribs or any other suitable means to prevent buckling. through the oute

15、r case, shall be straight and smooth, and have provisions for attaching the spigot. Corrosion-resistant steel surfaces shall be finished in accordance with 3.3.3. A spigot tube shall connect with the inner case, shall extend 3.4.2 Insulation. The space between the inner and outer cases of the con- t

16、ainer body and cover shall be lined with sufficient insulation to enable the container to satisfy the requirements of this specification, The insula- tion shall be polyurethane foam, glass wool, or equal and arranged so that it will remain in place throughout the life of the jug. 3.4.3 Spigot. The s

17、pigot shall be quick-flow, push type with provisions to prevent accidental discharge of liquid by bumping and shall be attached to the spigot adapter on the container body. detached, assembled, and disassembled for cleaning and sterilization, The spigot shall be of simple construction and shall cont

18、ain a minimum number of parts and a minimum number and length of joints. The metal parts of the spigot shall be made of corrosion-resistant steel, conforming to class 202, 302, or 304, condition A of qc-S-763 or of nickel-chromium plated brass. The parts of the spigot that must be handled to operate

19、 the flow control mechanism shall be made of a suitable non-metallic material of low thermal conductivity, having a minimum impact strength of 0.6 foot-pound per square inch of notch (hod). If a lock-ring, push-button arrangemenr: is used, the lock ring shall be threaded to the spigot barrel with a

20、standard acme thread conforming to Handbook H28. To facilitate cleaning and sanitation, the con- figuration shall provide maximum ease of disassembly and reassembly and mini- mum accumulation of food deposit. The spigot shall be easily attached, 3.4.4 Cover. The cover shall be fabricated of the same

21、 material as the con- tainer body. The cover shall have suitable quick connect and disconnect latches or clamps for attaching the cover to the body. The latches or clamps shall be specifically approved by the procuring activity, The cover shall have an indentation to accommodate the handle when it i

22、s not in Che carrying position. A suitable diameter metal tube, fabricated of the same material as the container, shall be inserted through the cover to equalize the pressure inside the container with the atmosphere. 3.4.5 Handle. A handle as shown in Figure 1, shall be provided on the cover and sha

23、ll be fabricated of either round or flat stock steel. If round stock is used, it shall conform to class 202, 302, or 304, condition A of Qt-S-763 with cold rolled surfaces. The handle shall have a minimum diameter of 3/16 inch except for the hand grip which shall have a minimum diameter of 318 inch.

24、 The hand grip shall have a minimum length of 3 112 inches, If flat stock is used, it shall conform to class 201, 202, 301, 302, or 304, condition A of QpS-766 with standard polish on both sides. thickness of 0.055 inch and a minimum width of 112 inch, The handle shall have a minimum 4 Provided by I

25、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M i k J-2 5 7 I 8 B (U SA F) t 1 I I WDJlT STUD UO. AR2- 3-4, ADAMS RITE MFG. CO. L : 2.3 3 O STELL. OR EQUAL, 5H: CADMIUM. I I _- Li +O 8 13- Provided by IHSNot for ResaleNo reproduction or networking permitted wit

26、hout license from IHS-,-,- MIL-J-257LB 73 7779906 0458046 b W f 3.4.6 Dry-ice well. When specified (see 6.2), a dry-ice well shall be pro- vided in the container cover or lid. The well shall be fabricated of the same material as the cover and shall have sufficient capacity to hold at least 1 112 pou

27、nds of dry ice, A screw-cap shall be provided on the lid for adding the dry ice. 3.4.7 Washers, gaskets and seals. The materials used for the lid gasket, spigot washer, and spigot shaft seal shall not become sticky in normal ser- vice, shall not swell to limit the functionability of the spigot, and

28、shall not be attacked by or impart toxic properties, tastes, or odors to liquid foods during the service life of the container. 3.4.8 Thermostat. The jug shall haue a thermostat of suitable power rating to maintain the temperature of the contents within the range specified when the container is oper

29、ating at any point within the ambient temperature range of plus 10 degrees to plus 180 degrees Fahrenheit. The thermostat shall be either a snap-action type or shall be equipped with a condenser of 0.5 MFD, lOO-volt, direct current capacitance to insure proper operation of the thermostat and to prev

30、ent burning and fusion of the thermostat contacts. 3.4.9 Electrical. All wiring and electrical connections shall be made in accordance with the applicable portions of MIL-W-5088. The jug shall con- form to the electrical interference requirements of MIL-STD-461 and MIL-STD- 462. 3.4.9.1 Heating elem

31、ents. Each jug shall be equipped with standard 130- watt, maximum, output heating elements for use with 28-volt (within limits of 25 to 29 volts) direct current and also for use with a 115-volt (within limits of 102 to 124 volts) alternating-current power supply. 3.4.9.2 Plug and receptacle. manufac

32、tured by the Cannon Electric Co., Los Angeles, California, or equal. The plug shall mate with receptacle part number 16707 manufactured by the Cannon Electric Co., or equal. The plug shall conform to part number 16706-1 3.5 Performance, Each jug shall meet the following performance criteria. 3.5.1 T

33、emperature control and operation. The thermostat and heater shall maintain the water temperature within the range of 170 to 190 degrees Fahren- heit when tested in accordance with 4.5.1. 3.5.2 Heat retention, perature of not more than 200 degrees Fahrenheit, the temperature of the con- tents shall n

34、ot decrease more than 65 degrees when tested in accordance with 4.5.2. With the jug filled with water preheated to a tem- 3.5.3 Thermal shock. The jug shall show no signs of damage when subjected ta thermal ehock and tested in accordance with 4.5.3. 6 Provided by IHSNot for ResaleNo reproduction or

35、networking permitted without license from IHS-,-,-MIL-J-25718B(USAF) 3.5.4 Overload. The jug shall function satisfactorily after 32 volts are applied to the 28-volt terminal and 125 volts are applied to the 115-volt terminal in accordance with 4.5.4. 3.5.5 Leakage. of the jug when tested in accordan

36、ce with 4.5.5. There shall be no leakage between the inner and outer cases 3.5.6 Dielectric. The jug shall withstand the application of 900-volts between the live parts and dead neta1 parts when tested in accordance with 4.5.6. 3.5.7 Handle and cover. There shall be no distortion, bending, cracking,

37、 or fastener failure of the handle or the cover when the jug is loaded and tested in accordance with 4.5.7. 3.5.8 Drainage. o liquid when tested in accordance with 4.5.8. 3.6 Identification. Eqiiipment, assemblies, and parts shall be mrked for identification in accordance with MIL-STD-130. Identific

38、ation shall include the following information: The jug shall drain all but a maximum of six fluid ounces Nomenclature Manufacturers Name Manufacturer s Model Designation Manufacturers Serial Number Contract or Order Number Federal Stock Number Date of Manufacture us 3.7 Workmanship. The container sh

39、all be uniform in quality and all compo- nents shall be assembled in a neat workmanlike manner. Parts shall be free from fractures, splits, punctures, dents, deterioration and shall not be bowed or malformed. Each unit shall be free of corrosion and all welds shall be smooth and complete. 4, QUALITY

40、 ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the con- tract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise speci- fied, the supplier may use his own or any facilities

41、 suitable for the per- formance of the inspection requirements specified herein, unless disapproved by the Government. inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. The Government reserves th

42、e right to perform any of the 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.2 Classification of inspection. The inspection requirements specified herein are classified as follows: MIL-J-25718B 73 7779706 0458048 T / r a. First article inspectio

43、n (see 4.2.1) b. Quality conformance inspection (see 4.2.2). 4.2.1 First article inspection. When first article approval is required under 3.1, first article inspection shall be performed. Unless otherwise specified (see 6.2), first article inspection shall comprise the examinations in 4.4.1 and 4.4

44、.2 and all tests in 4.5. Failure of the item to pass any examination or test shall be cause for disapproval of the first article. 4.2.2 uality conformance inspection. Quality conformance inspection shall be performed on sample units selected in accordance with 4.3. Unless other- wise specified (see

45、6.2), quality conformance inspection shall consist of the examination in 4.4.2 and the tests in 4.5.1, 4.5.4,.4.5.5, and 4.5.6, The acceptable quality levei shall be as specified in 4.3.1 for the examinations and 4.3.2 for the tests. 4.3 Sampling. Sampling lots for examinations and tests shall be se

46、lected in accordance with the provisions set forth in MIL-STD-105, except where other- wise indicated herein. For sampling purposes, a lot shall consist of all insulated jugs offered for delivery to the Government at one time under a specific contract. insulated jug. A sample unit shall consist of o

47、ne completely fabricated 4.3.1 SamplinP for examinations. A random sample of insulated jugs shall be selected from each lot in accordance with inspection level II of MIL-STO-105. The sampling level and acceptable quality level shall be as specified for each examina tion. 4.3.2 ted from each lot in a

48、ccordance with inspection level S-3 of MIL-STD-105. The acceptable quality level shall be 4.0 defects per 100 units. Sampling for tests. A random sample of insulated jugs shall be selec- 4.4 Examinations. 4.4.1 Component and material examination. In accordance with 4.1, canponents and materials shal

49、l be examined and tested in accordance with all the require- ments specified in reference specifications, drawings, and standards unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. 4.4.2 End product examination. The end product examination shall consist of a visual examination (see 4.k.2.1) and a weight and dimension examination (see 4.4.2.2). 8 Provided by IHSNot for ResaleNo reproductio