AIR FORCE MIL-C-26339 C-1982 CARRIER PASSENGER CARGO UTILITY FULL TRACK OVER-THE-SNOW TYPE《积雪型全面跟踪客运货运承运人的公用设施》.pdf

《AIR FORCE MIL-C-26339 C-1982 CARRIER PASSENGER CARGO UTILITY FULL TRACK OVER-THE-SNOW TYPE《积雪型全面跟踪客运货运承运人的公用设施》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-C-26339 C-1982 CARRIER PASSENGER CARGO UTILITY FULL TRACK OVER-THE-SNOW TYPE《积雪型全面跟踪客运货运承运人的公用设施》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-C-26339C 23 m 999990b 0333999 B I-, beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: HQ AFLC CASO/LODSAC, Federal Center, Battle Creek, MI 49016 by using the self-addressed Standardization D

2、ocument Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. M L-C-26 9C 6 Dec 8% SUPERSEDING MIL-C-2633 9B 25 May 1967 MILITARY SPECIFICATION CARRIER, PASSENGER, CARGO, UTILITY, FULL TRACKED, OVER-THE-SNOW TYPE This specification is approved for use by all Departm

3、ents and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers five sizes of cargo, utility and pas- senger carrying, full tracked, arctic tracklaying vehicles. 1.2 Classification. Cargo carriers shall be of the size specified (see 6.2). Size 1 - Carrier, Cargo, Flatbe

4、d, With Cab, 2 Passenger Size 2 - Carrier, Cargo, Flatbed, With Cab, 4 Passenger Size 3 - Carrier, Cargo, Flatbed, With Cab, 6 Passenger Size 4 - Carrier, Combination Cab and Cargo Type Body, 10 Passenger Size 5 - Carrier, Utility, With Cab, With Snow Plow Blade (see 3.12). 2. APPLICABLE DOCUMENTS 2

5、.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS Federal F-P-666 W-B-131 O-E-91 5 Militarv Primer, Pressure, Internal Combustion Engine (Cold Starting Aid) and Pr

6、imer , Cartridges Battery, Storage; Vehicular, Ignition, Lighting and Starting Extinguisher, Fire, Dry-Chemical (Hand Portable) MIL-A-11755 Antifreeze, Arctic Type MIL-A-2730 2 Arrestor, Spark, Exhaust, Internal Combustion MIL-C-1283 Can, Gasoline, Military, 5-Gallon MIL-P-5 14 Plate, Identification

7、 and Plate, Identification Eng i ne Transportation Data STANDARDS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-26339C 23 m 7999906 0194000 9 W . MIL-C-26339C Military MIL-STD- 8 1 O MIL-STD-1223 Administrative Wheeled Vehicle Treatment, Pain

8、ting MIL-STD-1472 MS 51335 Pintle Assembly, Towina Environmental Test Methods and Data Plate Standard Human Engineering Design Criteria for Military Sys- tems, Equipment and Facilities (Copies of specifications, standards, drawings and publications required by suppliers in connection with specific p

9、rocurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications. cation to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply. The follo

10、wing documents form a part of this specifi- SOCIETY OF AUTOMOTIVE ENGINEERS, INC. (SAE) CAE Standards and Recommended Practices 5551 5552 55 37 Measurement of Electromagnetic Radiation from Motor Vehicles (20-1000 Mhz) External Electromagnetic Radiation Suppressors Storage Batteries (Information as

11、to the availability of this handbook may be obtained from the Society of Automotive Engineers, Inc., Two Pennsylvania Plaza, New York, NY 10001.) THE TIRE AND RIM ASSOCIATION, INC. (TRA) Year book (Application for copies should be addressed to the Tire and Rim Association, Inc., 200 W. Market St., A

12、kron, OH 44313.) DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regulations (FMCSR) (Application for copies should be addressed to the US Department of Transporta- tion, Federal Highway Administration, Washington, M: 20591.) 3. REQUIREMENTS 3.1 First article. When specified (see 6.2

13、), the contractor shall furnish a carrier for first article inspection (see 4.2.1). 3.2 Standard chassis components and accessories. Except as specified in this specification, the chassis components, assemblies, and accessories to be de- livered under this contract shall be standard or optional item

14、s which meet or exceed the requirements of this specification. All chassis items shall be as represented in the chassis manufacturers technical data. All chssis items considered standard equipnent on the vehicle model to be supplied under appli- cable contract shall be furnished except when optional

15、 equipnent is required. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-Zb339C 23 9999906 0194001 O = _1 I MIL-C-26339C 3.3 Rustproofing. The vehicle shall be rustproofed in accordance with the requirements of MIL-STD-1223. 3.4 Drain plugs. A

16、ll drain plugs installed throughout the vehicle for the purpose of draining lubricants shall be the permanent/magnet type and shall be readily accessible. Lubrication system shall permit use of arctic lubricants. 3.5 Design and construction. The carrier shall be a gasoline or diesel engine driven tr

17、acklaying vehicle designed for carrying cargo and passengers and shall be capable of meeting the requirements specified herein. 3.5.1 Weights and dimensions. The vehicle shall provide for weights and dimen- sions as follows:. Size 1 a. b. C. d. e. f. 4. h. i. Curb weight, lbs (Max) 8,660 lbs (Min) G

18、round Pressure, lbs per sq inch (Max) at curb wt. .98 Overall Width, Inches (Max) 118 Overall Height, Inches (Max) 102 Overall Length in (Max) 19 o Ground Clearance, Inches (Min) 11 Inside Body Height, Inches (Min) 44 Inside Body Width, Inches (Min) 70 Load Space: Width, Inches (Min) 70 Length, Inch

19、es (Min) 70 Size 2 8,660 98 118 10 2 19 o 11 44 70 70 48 Size 3 Size 4 Size 5 8,660 98 11 8 102 190 11 44 70 70 48 8,660 .98 118 10 2 190 11 44 70 70 96 11,000 9,500 .98 150 10 2 190 11 44 30 N/A N/A 3.5.2 Maintainability. The carrier shall be designed so that normal adjust- ments, repairs, lubricat

20、ion and overhaul can be readily accomplished by the use of general purpose tools with a minimum removal of or disturbance of other ele- ments of the carrier . 3.5 Performance. The carrier shall meet the load carrying, load towing and mobility requirements under the environmental conditions specified

21、 herein with the engine derated to 6,000 feet altitude (engine manufacturers data shall be fur ni shed. 3.6.1 Environmental conditions. The carrier shall be capable of satisfactory operation and storage in ambient temperatures ranging from -30F to +65“F and shall be capable of withstanding rain as e

22、ncountered in any locale. When win- terization is specified (see 3.13), the carrier shall be capable of satisfac- tory operation and storage in ambient temperatures ranging from -70F to +65“F. 3.6.2 Load carrying and towing capability. The carrier shall be capable of 3 Provided by IHSNot for ResaleN

23、o reproduction or networking permitted without license from IHS-,-,- - MIL-C-2b337C 23 m 777770b 0374002 2 m MIL-C-26339C carrying the following cargo and passengers. Size 1 - Operator, one passenger, and cargo load of 2000 pounds minimum evenly distributed over the cargo space. Size 2 - Operator, t

24、hree passengers, and cargo load of 1650 pounds mini- mum evenly distributed over the cargo space. Size 3 - Operator, 5 passengers and a cargo load of 1300 pounds minimum evenly distributed over the cargo space. Size 4 - Operator and 9 passengers and operator and a cargo load of 1575 pounds minimum e

25、venly distributed over the cargo space. Size 5 - Operator only. The carriers shall be capable of towing a trailer and cargo sled having a gross weight of 1500 pounds. Full load consists of curb weight, operator, passengers, and payload. For purposes of this specification, operator weight is equivale

26、nt to 175 pounds. 3.6.3 Mobility. When fully loaded, the carrier shall be capable of operating satisfactorily over hard packed level snow and smooth level ground at a speed of not less than 15 miles per hour (mph) (11 mph for size 5 vehicles) and not more than 25 mph for at least 120 miles without d

27、amage or refueling. Vehicle shall be capable of being operated at medium speeds (4-10 mph) for extended periods of time in mountainous terrain without overheating the engine and with- out failure. The vehicle shall develop a drawbar pull of not less than 13,000 pounds on snow surface, for size 5. 3.

28、6.3.1 Turning. Carrier turning radius for left and right turns shall not exceed 15 feet and shall be measured from the pivot point to inside edge of inner track . 3.6.3.2 Gradeability. and descending continuous grades of not less than 80 percent (%). loaded carrier shall be capable of operating, sto

29、pping and starting on a side slope of not less than 60%. The fully loaded carrier shall be capable of ascending The fully 3.7 Chassis. 3.7.1 Engine. The engine, complete with all necessary components and acces- sories, shall be a commercial industrial class, liquid cooled, internal com- bustion, fou

30、r-stroke cycle, gasoline type or a liquid cooled, internal combus- tion four-stroke cycle, diesel type. If gasoline engine is furnished, it shall produce the required vehicle performance when operated on unleaded fuel with a research octane rating of 91, at engine speed not more than the manu- factu

31、rers recommended operating speed. The engine shall have not less than 6 cylinders if gas type and four cylinders if diesel type and shall incorpo- rate a crankcase ventilation system. requirements contained herein, including the side slope ability. The engine shall be equipped with a locking hand th

32、rottle located on the instrument pan- el. The engine shall start within five minutes and be ready for full load operation within fifteen minutes in any ambient temperature specified in 3.6.1. When specified (see 6.2), a fluid priming system, conforming to F-P-666, Type The engine shall meet the oper

33、ational 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-26339C 23 m 997990b 0194003 4 m MIL-C-26339C I, size 2, shall be completely installed; only steel clad, corrosion-resistant cartridges shall be used. A lubricating oil filter of the full

34、 flaw type shall be furnished. when the cleaner is of the oil bath type, its oil capacity shall be not less than one pint. The thermostat furnished for the engine cooling system shall be of the range from 170F to 195F. The engine shall be furnished with an intake air cleaner and 3.7.2 Fuel tank. The

35、 fuel tank furnished shall be located rearward of the cab on sizes 1, 2, 3 and 5 and rearward of the operators seat on size 4 vehicles, and shall provide capacity necessary to conform to 3.6.3. The tank vent and filler lines shall be conveniently located so as to prevent gasoline fumes and leakage i

36、nside the vehicle. 3.7.3 Transmission. An automatic or hydrostatic transmission shall be pro- vided. The automatic transmission shall have a minimum of three forward speeds and 1 reverse speed and shall provide for driver selection of indivi- dual gears and ranges of gears. speeds that are infinitel

37、y variable for the entire speed range in forward and reverse direction. The transmission shall have a torque capacity adequate to transmit the maximum gross torque of the engine through all gear reductions. The hydrostatic transmission shall provide 3.7.4 Heater and defroster. Vehicle cab shall be p

38、rovided with a 12 volt hot water heater with fresh air intakes and discharge outlets to the floor and to the windshield defroster louvers. Heater shall be complete with blower and mounted controls convenient to the driver. Heater shall be capable of maintaining the temperature of the cab air at the

39、carrier floor above 40F when the ambient temperature is -25F with no solar input. When winterization is specified (see 3.13), the heater shall be capable of maintaining the temp- erature of the cab air at the carrier floor above 40F when the ambient temp- erature is -60F with no solar input. 3.7.5 T

40、rack control assembly. The track control shall consist of a lever(s), or steering wheel and column which shall be suitable located for left hand dr ive. 3.7.6 Drive line assembly. The drive line components shall be of adequate strength to transmit the maximum torque developed through all gear train

41、re- duc t ions. 3.7.7 Tracks. The carrier shall be equipped with two full driving tracks designed to provide continuous support to the carrier at all ground contact points. The track assemblies shall operate in varied terrain such as sand, mud, snow, ice and bare ground without excessive wear and br

42、eakage. The track design shall provide for repair of track, and for removal and replace- ment of track cleats. The track width and the length of the track contacting the ground shall provide a ground pressure not more than that specified in 3.5.1. Track mounting shall provide for not less than 4 inc

43、hes of track tension adjustment or shall be continuous spring tension type providing self adjustment of track tension. Track design shall provide independent control of each track. 3.7.8 Suspension system. The suspension system shall consist of axles and automotive tire assemblies independently moun

44、ted on each side of the carrier to avoid lateral stresses through the frame. The design of the linkage as- sembly shall permit the articulation in a vertical plane of the wheel and 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-26339C tire a

45、ssemblies so that a constant downward pressure is applied when the ye- hicle is operated on uneven surfaces and the track guides are retained in one vertical plane. 3.7.8.1 Axles. The axles shall provide for mounting of the wheel and tire assemblies. The axles shall be adequate for the loads imposed

46、 by the fully equipped and fully loaded carrier under the operating conditions specified herein. 3.7.8.2 Wheel and tire assemblies. The wheel and tire assemblies furnished shall be the Manufacturers recommended wheel and tire assemblies. Tires serv- ing as track tensioning surfaces shall be hard rub

47、ber. Tires shall provide adequate support for the vehicle and to the tracks when the vehicle is fully loaded to rated GVM. Tires and rims shall be in accordance with the requirements of the Tire and Rim As soci at ion recommend at ions. Pneumatic tires shall be Urethane foam filled type. 3.7.9 Braki

48、ng system. The braking system furnished shall be capable of com- pletely locking the tracks under all conditions of use. A separate emergency brake shall be incorporated in the drive system and shall be capable of hold- ing the fully loaded carrier stationary on a slope headed either direction equal

49、 to its grade climbing ability. The emergency brake handle shall be lo- cated so as to be easily operated by the driver. 3.7.10 Exhaust system. Exhaust system shall conform to Vehicle Motor Car- rier Safety Regulation 393.83. the vehicle or at least ten inches above the cab and be so located as to minimize the possibility of exhaust fumes entering the body of the vehicle. A spark arrestor, conforming to the material and performance requirements of MIL-A-27302, shall be f