AIR FORCE A-A-58028 D-2010 TRUCK FIRE FIGHTING HAZARDOUS MATERIALS (HAZMAT) RESPONSE VEHICLE《消防车 危险物品(有害物质)接警车》.pdf

《AIR FORCE A-A-58028 D-2010 TRUCK FIRE FIGHTING HAZARDOUS MATERIALS (HAZMAT) RESPONSE VEHICLE《消防车 危险物品(有害物质)接警车》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE A-A-58028 D-2010 TRUCK FIRE FIGHTING HAZARDOUS MATERIALS (HAZMAT) RESPONSE VEHICLE《消防车 危险物品(有害物质)接警车》.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: WR-ALC 542 CSW/CBSSS, 295 Byron Street, Robins AFB, GA 31098-1611. Since contact information can change, you may want to verify the currency of this address

2、 information using the ASSIST Online database at https:/assist.daps.dla.mil/online . FSC 4210 INCH-POUND A-A-58028D 23 SEP 2010 SUPERSEDING A-A-58028C 27 May 2009 COMMERCIAL ITEM DESCRIPTION TRUCK, FIRE FIGHTING, HAZARDOUS MATERIALS (HAZMAT) RESPONSE VEHICLE The General Services Administration has a

3、uthorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers a commercial hazardous materials (HazMat) truck. It has a 4x2 or a 4x4 chassis with a diesel engine and an automatic transmission; a cab with at least three doors w

4、hich can accommodate at least four seated persons; and a utility body for equipment storage. The HazMat truck is intended to stow and transport hazardous materials response equipment for the purpose of mitigating chemical leaks, spills, and releases of hazardous substances in both on- and off-road e

5、nvironments. The HazMat truck is also intended to provide a hazardous materials incident command work station area for the purpose of research, command, control, and communications. 2. SALIENT CHARACTERISTICS. The hazardous materials truck shall be in accordance with the applicable requirements of t

6、he following chapters of National Fire Protection Association (NFPA) 1901, Standard for Automotive Fire Apparatus, Current Edition, for Special Service Fire Apparatus: Chapter Title 1 Administration 2 Referenced Publications 4 General Requirements 10 Special Service Fire Apparatus 12 Chassis and Veh

7、icle Components 13 Low-Voltage Electrical Systems and Warning Devices 14 Driving and Crew Area 15 Body, Compartments, and Equipment Mounting 23 Line Voltage Electrical Systems 25 Air Systems Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58028D

8、2 Chapter Title 26 Winches Unless otherwise specified (see 6.2), the vehicle shall have a 4x2 chassis. The 4x2 and 4x4 versions shall be identical except for the driveline differences and as otherwise specified herein. 2.1 Administration. 2.1.1 Environmental conditions. 2.1.1.1 Altitude. Unless othe

9、rwise specified (see 6.2), the vehicle shall be designed for operation at 2,000 feet above sea level. 2.1.1.2 Temperature range. The vehicle shall be capable of satisfactory storage and operation in temperatures ranging from 0 to 125 F. When specified (see 6.2), the vehicle shall be equipped with a

10、winterization system that includes an engine coolant heater and a battery heater (a blanket type battery heater is not acceptable). The winterization system shall be powered through the electrical shoreline connection (see 2.6.2). 2.1.2 Foreign object damage. All loose metal parts, such as pins and

11、valve caps, shall be securely attached to the vehicle with wire ropes or chains. “Dog tag“ style beaded chains shall not be provided. Removable panels, if provided, shall be attached with captive fasteners. 2.1.3 Roadability. 2.1.3.1 Operating terrain. The vehicle shall operate on paved and graded g

12、ravel roads; the 4x4 version shall also operate on off-road (cross country) terrain. 2.1.3.2 Acceleration. The fully loaded vehicle shall accelerate from 0 to 50 miles per hour (mph) within 60 seconds on a level, paved road. 2.1.3.3 Maximum speed. The fully loaded vehicle shall attain a minimum top

13、speed of 65 mph on a level, paved road. 2.1.3.4 Gradeability. The fully loaded vehicle shall be able to maintain a speed of at least 30 mph while ascending any paved slope up to and including 8.0 percent. The fully loaded 4x4 version shall also be able to maintain a speed of at least 5.0 mph while a

14、scending any paved slope up to and including 30 percent. 2.1.4 Overall dimensions. Overall dimensions shall be the minimum consistent with the operational performance and the design constraints necessary to achieve the specified performance. Overall dimensions shall not exceed: Length 390 inches Wid

15、th 100 inches (excluding mirrors) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58028D 3 Height 130 inches (44) 2.1.5 Turning diameter. The fully loaded vehicle shall have a wall to wall turning diameter of less than three times the length of t

16、he vehicle. 2.1.6 Angles of approach and departure. The fully loaded vehicle shall have angles of approach and departure of not less than 11. 2.1.7 Vehicle Stability. Vehicle shall comply with roll over stability criteria as defined by NFPA 1901, paragraph 4.13. 2.1.8 Manuals. 2.1.8.1 Technical manu

17、als. The overall format for the manuals may be military specification, commercial, or a combination of both. Each technical manual shall have a title page. a. The contractor shall validate the technical manuals for accuracy prior to submission to the procuring activity for verification. The contract

18、or shall submit one complete set to the procuring activity for verification 30 days before the first production test. Any changes or corrections noted by the procuring activity shall be corrected and updated pages or manuals shall be submitted to the procuring activity. b. Once approved by the procu

19、ring activity, the contractor shall pack two complete sets of technical manuals with each vehicle. An additional two complete sets shall be submitted to the procuring activity for stock. c. Once approved by the procuring activity and a Technical Order number is assigned, the contractor shall pack tw

20、o complete sets of both hard copy and CDs with each vehicle and one complete set of both hard copy and CDs shall be submitted to the procuring activity for stock. The procuring activitys address will be provided. d. The contractor shall grant the United States Air Force a non-exclusive, non-assignab

21、le, royalty free U.S. Government (Government) Purpose License, to scan into CENTRA (the USAF repository) and to reproduce and distribute (either electronically or via hard medium) copies or facsimiles of manuals produced and distributed by the contractor for this CID. These rights extend to Governme

22、nt agencies only, and the data contained in the technical manuals is not to be sold, disclosed or otherwise provided to any other entity or entities outside the Government. The license shall remain in effect as long as the vehicles described in the required technical manuals remain under Government

23、control and usage. In addition, the contractor shall grant permission for the Government to place an Air Force TO (Technical Order) number and publication date as well as distribution, warning, handling and destruction statements on the cover / title pages of the TO. Provided by IHSNot for ResaleNo

24、reproduction or networking permitted without license from IHS-,-,-A-A-58028D 4 2.1.8.1.1 Operators manuals. The operators manual shall include all information required for the safe and efficient operation of the vehicle, including any special attachments or auxiliary equipment. The operators manual

25、shall include at least the following: a. Location and function of all controls and instruments shall be illustrated and fully described. b. Safety information that is consistent with the safety standards established by the Occupational Safety and Health Administration (OSHA). c. Checks and adjustmen

26、ts in preparation for placing the vehicle for service upon receipt from the contractor. d. Preparation for shipment or storage. e. Warranty information and period of the warranty for the complete vehicle and for any component warranty that exceeds the warranty of the complete vehicle. Addresses and

27、telephone numbers shall be provided for all warranty providers. f. General description of and step-by-step instructions for the operation of the vehicle and its auxiliary equipment. g. Description of the post-operational procedures (draining, flushing, et cetera). h. Checklists for the daily mainten

28、ance inspection and mission readiness checks that the operator is expected to perform. i. Procedures for towing the HazMat truck if it becomes disabled. j. Schedules for required preventative maintenance and required periodic maintenance. 2.1.8.1.2 Service manuals. The service manual shall identify

29、any special tools and test equipment required and shall cover troubleshooting and maintenance as well as minor and major repair procedures. The text shall contain performance specifications, tolerances, and fluid capacities; current, voltage, and resistance data; test procedures; and such illustrati

30、ons and exploded views as may be required to permit proper maintenance by qualified mechanics. The manual shall contain an alphabetical subject index as well as a table of contents. The service manual shall contain at least the following, where applicable: a. Hydraulic schematic. b. Pneumatic schema

31、tic. c. Electrical schematic. d. Winterization schematic. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58028D 5 e. Schedules for required preventative maintenance and required periodic maintenance. f. Location, procedure, and interval for part

32、s of the truck and equipment which require lubrication. 2.1.8.1.3 Parts manual. The parts manual shall include illustrations and exploded views, as needed, to properly identify all parts, assemblies, subassemblies, and special equipment. All components of assemblies shown in illustrations or explode

33、d views shall be identified by reference numbers which correspond to the reference numbers in the parts lists. All purchased parts shall be cross-referenced with the original manufacturers name and part number. The parts identification manual shall provide the description, length, dimensions, and qu

34、antity of each item used per vehicle. The manual shall contain a numerical index. The parts manual shall contain a list of all of the component vendor names, addresses, and telephone numbers referenced in the parts list. 2.1.9 Painting, plating, and corrosion control. 2.1.9.1 Dissimilar metals. Diss

35、imilar metals, as defined in MIL-STD-889, shall not be used in intimate contact with each other. 2.1.9.2 Finish. Exterior surfaces shall be prepared, primed, and painted with polyurethane paint in accordance with all of the paint manufacturers instructions and recommendations. Unless otherwise speci

36、fied (see 6.2), the exterior finish color shall be Candy Apple Red, Sikkens Color Number FLNA3021, DuPont Color Number 97902U or 4737U, PPG Color Number 71528 (the PPG name for this color is Cardinal Red), or equal. When specified, the exterior finish color shall be Desert Sand, Color Number 30313 o

37、f FED-STD-595. a. For vehicles painted Candy Apple Red, the cab upper body (from the bottom of the windshield) and roof shall be painted White, Color Number 17875 of FED-STD-595. Compartment interiors shall have a standard commercial finish. All bright metal and anodized parts, such as mirrors, horn

38、s, light bezels, and tread plates, shall not be painted. Roll-up compartment doors may be painted or unpainted. b. For vehicles painted Desert Sand, all exterior surfaces, excluding all normally bright metal and anodized parts and any interior surfaces visible with any compartment door open (but not

39、 the interior of the cab), shall be painted body color. This includes compartment shelves and mounting hardware, but does not include items mounted in the compartments. Non-metallic materials may be black or gray. 2.1.9.3 Reflective stripes. Vehicles shall be uniformly marked with reflective stripin

40、g to comply with the surface area of coverage as prescribed by, and 15.9.3 of NFPA Standard 1901, Automotive Fire Apparatus. Perimeter horizontal striping will be located below the body centerline, covering at least 60 percent of the length (or as space permits) of each facing surface (length or wid

41、th). Bright metal trim or anodized parts may interrupt the reflective stripes. The pattern shall be a 7-inch pattern: 1-inch stripe, 1-inch body color, 3-inch stripe, 1-inch body Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58028D 6 color, 1-i

42、nch stripe (1-3-1). The reflective stripes shall be white for vehicles painted Candy Apple Red and Desert Sand. 2.1.9.4 Chevron Striping. In accordance with 15.9.3.2 of NFPA 1901 at least 50 percent of the rear-facing vertical surfaces, visible from the rear of the apparatus, excluding any pump pane

43、l areas not covered by a door, shall be equipped with retroreflective striping in a chevron pattern sloping downward and away from the centerline of the vehicle at an angle of 45 degrees. 3M part number 983-17 (red) and 983 -23 (florescent yellow/green) reflective diamond grade or equivalent shall b

44、e utilized. stripe in the chevron shall be a single color alternating between red and fluorescent yellow in accordance with 15.9.3.2.1. Each stripe shall be 6-inches (150 mm) in width in accordance with 15.9.3.2.2 of NFPA 1901 and the example provided below. 2.1.9.5 Lettering. Vehicles painted Candy

45、 Apple Red shall have the letters UNITED STATES and AIR FORCE applied in synthetic or encapsulated gold leaf, with outline and black shadow, on the front door on both sides in long radius elliptical arches above and below the lettering center line. The size of the lettering shall be a minimum of 2-i

46、nches to a maximum of 6-inches. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58028D 7 Vehicles painted Desert Sand shall not have lettering. 2.1.10 Identification plate. A permanently marked identification plate shall be securely mounted at th

47、e drivers compartment. The identification plate shall contain the following information: a. NOMENCLATURE b. MANUFACTURERS MAKE AND MODEL c. MANUFACTURERS SERIAL NUMBER d. USAF VEHICLE REGISTRATION NUMBER e. NATIONAL STOCK NUMBER (NSN) f. VEHICLE CURB WEIGHT: kg (pounds) g. PAYLOAD, MAXIMUM: kg (poun

48、ds) h. GROSS VEHICLE WEIGHT (GVW): kg (pounds) i. FUEL CAPACITY AND TYPE: gal (gallons) / L (liters) j. DATE OF DELIVERY (month and year) k. WARRANTY (months and km (miles) l. CONTRACT NUMBER m. PAINT COLOR AND NUMBER n. LENGTH, WIDTH, AND HEIGHT OF VEHICLE IN INCHES AND CENTIMETERS. 2.2 Chassis and

49、 vehicle components. 2.2.1 Capacity. The vehicle shall have a payload capacity of 8,000 pounds of equipment and an additional allowance for two crew members and shall have a minimum Gross Vehicle Weight Rating (GVWR) of 34,500 pounds. 2.2.2 Engine. The truck shall have a diesel engine that is certified to comply with the Environmental Protection Agency (EPA) on-highway emission requir